Enablement Kit Version: 6.0.0.0-14 ---------------------------------- v6.04 build56: ------------- Defect/Enhancement: Defect Problem: LUN QoS API returns "Not Supported" Solution: Fixed QoS value read issue in BSG path Introduced: v6.04 build21 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 ISP2071, ISP2271, ISP2261, ISP2871, ISP2971, ISP2A61, ISP2031 OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.0-15 ---------------------------------- v6.04 build57: ------------- Defect/Enhancement: Defect Problem: Delay seen in Application bringup on some inbox drivers Solution: Do not perform retries for newer features if driver returns not supported error Introduced: v6.04 build28 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 ISP2071, ISP2271, ISP2261, ISP2871, ISP2971, ISP2A61 OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.0-16 ---------------------------------- v6.04 build63: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Allow NVMe specific APIs for newer ISPs Introduced: v6.04 build63 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 ISP2071, ISP2271, ISP2261, ISP2871, ISP2971, ISP2A61 OS: All supported Linux flavors Protocol: FC v6.04 build62: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added ISP FW and MPI FW lockdown bits Introduced: v6.04 build62 Impact: HW: ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build61: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Provide lockdown mode error codes to apps Introduced: v6.04 build61 Impact: HW: ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build60: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added adapter firmware lockdown support Introduced: v6.04 build60 Impact: HW: ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build59: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added EP2989 support Introduced: v6.04 build59 Impact: HW: EP2989 OS: All supported Linux flavors Protocol: FC v6.04 build58: ------------- Defect/Enhancement: Defect Problem: HBA Parameters read fails for newer adapters for inbox drivers Solution: Read active HBA Parameters region set from flash Introduced: v6.04 build24 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.0-17 ---------------------------------- v6.04 build75: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Mailbox passthru support Introduced: v6.04 build75 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build74: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added NVRAM parameters for SCMR Profile support Introduced: v6.04 build74 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build73: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added SCMR Profile support Introduced: v6.04 build73 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build72: ------------- Defect/Enhancement: Defect Problem: Random apps crash seen when large number of vports present Solution: Validate vport memory pointers before accessing it Introduced: v6.04 build24 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build71: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added EP2881 and EP2981 support Introduced: v6.04 build71 Impact: HW: EP2881, EP2981 OS: All supported Linux flavors Protocol: FC v6.04 build70: ------------- Defect/Enhancement: Defect Problem: Flash update failure on UOS on ARM (aarch64) Solution: Corrected BSG pointers for UOS on ARM Introduced: v6.04 build24 Impact: HW: ISP2071, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build69: ------------- Defect/Enhancement: Defect Problem: Invalid LUN size display for small sized (In MBs) and large sized (in TBs) NVMe LUNs Solution: Use correct read capacity format to get LUN size of NVMe LUNs Introduced: v6.04 build52 Impact: HW: ISP2071, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build68: ------------- Defect/Enhancement: Defect Problem: Apps delay seen with NVMe targets Solution: Cache common NVMe target data to avoid multiple calls to NVMe targets Introduced: v6.04 build52 Impact: HW: ISP2071, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build67: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Session shutdown state macro support Introduced: v6.04 build67 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build66: ------------- Defect/Enhancement: Defect Problem: Apps crash seen with HBA_RemoveCallback SNIA API Solution: Avoid double free of memory freed in HBA_RemoveCallback SNIA API Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build65: ------------- Defect/Enhancement: Defect Problem: Apps delay seen with disabled/isolated port Solution: Avoid apps retries for disabled/isolated port Introduced: v6.04 build24 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build64: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added USCM Phase 2 support Introduced: v6.04 build64 Impact: HW: ISP2071, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Defect Problem: Apps crash seen with disabled/isolated port Solution: Fixed apps crash with disabled/isolated port Introduced: v6.04 build24 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.0-18 ---------------------------------- v6.04 build81: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added NVRAM parameters for UEFI boot support Introduced: v6.04 build81 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build80: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added additional USCM statistics info Introduced: v6.04 build80 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build79: ------------- Defect/Enhancement: Defect Problem: Port reset seen on all ports of the adapter after HBA parameter update Solution: Allowed reset only in HBA parameter modified port Introduced: v6.04 build24 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289, ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build78: ------------- Defect/Enhancement: Defect Problem: Apps crash seen with DPort test with newer firmware Solution: Increase response buffer size to read extra data provided by FW Introduced: v6.04 build24 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build77: ------------- Defect/Enhancement: Defect Problem: NPIV port seen as physical port on newer OSes Solution: Corrected host number list Introduced: v6.04 build24 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build76: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added FC-GS-8 based speed definitions Introduced: v6.04 build76 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.0-19 ---------------------------------- v6.05 build7: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Use 32bit buffer size of SFP FW update Introduced: v6.05 build7 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.05 build6: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added 64G FC SFP FW update support Introduced: v6.05 build6 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.05 build5: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Remote Port API support Introduced: v6.05 build5 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.05 build4: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Secure Port V2 API support Introduced: v6.05 build4 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.05 build3: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Klocwork static analysis fixes Introduced: v6.05 build3 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.05 build2: ------------- Defect/Enhancement: Defect Problem: Feature API confilct seen FOAPI Solution: Removed conflicting duplicate feature APIs Introduced: v6.05 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.05 build1: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Klocwork static analysis fixes Introduced: v6.05 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build90: ------------- Defect/Enhancement: Defect Problem: Incorrect NVMe portID seen when multiple targets present Solution: Provide valid PortIDs for NVMe targets Introduced: v6.04 build85 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289, ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build89: ------------- Defect/Enhancement: Defect Problem: Incorrect secure target fields seen Solution: Provide valid info for secure targets Introduced: v6.04 build54 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build88: ------------- Defect/Enhancement: Defect Problem: NVRAM dat file update failure on 8G adapter Solution: Fixed dat file update on 8G adapter Introduced: v6.04 build2 Impact: HW: ISP2532 OS: All supported Linux flavors Protocol: FC v6.04 build87: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Uncorrectable FEC error count support in USCM stats Introduced: v6.04 build87 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289, ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build86: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added I/O Throttling support Introduced: v6.04 build86 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289, ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build85: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added PortID support for NVMe targets Introduced: v6.04 build85 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289, ISP2071, ISP2271, ISP2261 OS: All supported Linux flavors Protocol: FC v6.04 build84: ------------- Defect/Enhancement: Defect Problem: Boot code valid bit is set for all boot codes Solution: Set boot code valid bit only when valid boot code is found Introduced: v6.04 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v6.04 build83: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added Virtual Lane support Introduced: v6.04 build83 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v6.04 build82: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added new NVRAM parameters Introduced: v6.04 build82 Impact: HW: ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.1-1 ---------------------------------- v7.00 build1: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Use OS provided libsysfs library Introduced: v7.00 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC Defect/Enhancement: Enhancement Problem: N/A Solution: Added Klocwork static analysis fixes Introduced: v7.00 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.1-2 ---------------------------------- v7.00 build3: ------------- Defect/Enhancement: Defect Problem: Apps issue seen with static library Solution: Fixed static library issue Introduced: v7.00 build2 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v7.00 build2: ------------- Defect/Enhancement: Defect Problem: Apps runtime failure on RHEL 9 due to libsysfs function Solution: Removed dependency of libsysfs function Introduced: v7.00 build1 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.1-3 ---------------------------------- v7.00 build6: ------------- Defect/Enhancement: Defect Problem: checksec.sh reported security property issues Solution: Fixed checksec.sh reported security property issues Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v7.00 build5: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added driver maintenamce mode support for FW load error Introduced: v7.00 build5 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v7.00 build4: ------------- Defect/Enhancement: Defect Problem: Debug symbols present in library binary Solution: Removed debug symbols from library binary Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC Enablement Kit Version: 6.0.0.1-4 ---------------------------------- v7.00 build11: ------------- Defect/Enhancement: Defect Problem: Incorrect USCM congestion severity value seen with USCM phase 2 support Solution: Read USCM congestion severity value in USCM phase 2 support Introduced: v6.04 build64 Impact: HW: ISP2071, ISP2261, ISP2081, ISP2281, ISP2089, ISP2289 OS: All supported Linux flavors Protocol: FC v7.00 build10: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Updated SNIA HBA API speed definitions Introduced: v7.00 build10 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v7.00 build9: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Updated SFP read enhancements macros Introduced: v7.00 build9 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v7.00 build8: ------------- Defect/Enhancement: Enhancement Problem: N/A Solution: Added SFP read enhancements Introduced: v7.00 build8 Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC v7.00 build7: ------------- Defect/Enhancement: Defect Problem: Invalid error seen when multiple SG's failed at driver level Solution: Added new error code for multiple SG failure Introduced: Day One Impact: HW: All adapters OS: All supported Linux flavors Protocol: FC - ENHANCEMENTS - ENHANCEMENTS - ENHANCEMENTS - Removed support for RHEL 8U6 - Removed support for RHEL 8U7 - Added support for SLES 15 SP6 - Added support for RHEL 9U4 - Added support for RHEL 8U10 - Removed support for ALP SP0 - Added support for RHEL 9U5 - Added support for RHEL 10u0 - Added support for SLES 15 SP7 - Removed support for RHEL 9U2 - Added support for RHEL 9U6 - Removed support for RHEL 8U6 - Removed support for RHEL 8U7 - Added support for SLES 15 SP6 - Added support for RHEL 9U4 - Added support for RHEL 8U10 - Removed support for ALP SP0 - Added support for RHEL 9U5 - Added support for RHEL 10u0 - Added support for SLES 15 SP7 - Removed support for RHEL 9U2 - Added support for RHEL 9U6 - Improved the fan calibration during server power-on. * Improved the format of the Chassis CPLD version reported in Integrated Lights-Out 5 (iLO 5) and the Chassis Controller CLI. * Improved the fan behavior when a server blade stops communicating with the Chassis Controller. * Added support for Murata Power Supply Kits. - None - Added Fan-FailSafe which continually checks to see if an installed, powered blade is communicating with the HPE Edgeline Chassis Controller. If there is no communication for 90 seconds or more, the fans will go to full blow. When the blade begins to communicate again, the fans will return to normal. - N/A - - Added support for HPE Compute Edge Server e930t - SHA384 fix - SHA384 fix - Signed with SHA384 - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.16 (01/30/2024) or later. **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may enter standby mode on Power-On Self-Test (POST) during warm reset cycle. Addressed an issue where system may stop responding at "Memory Initialization - Start" during Power-On Self-Test (POST). **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - Resolved various issues to improve system stability and performance. - Firmware contains fix for bug that may cause drive to perform self-initiated reset in systems where maximum queue depth of 128 is exceeded. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - High Security Enablement support FIPs - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Assert fixes, logging enhancements and all current firmware improvements and bug fixes. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixed flashing issue through SDR method - Fix to Assert fixes, current firmware improvements and bug fixes. - - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - This component provides support only for VMD enabled Intel VROC platform. - Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Fixed Reset issue and regular maintenance firmware update. - Fixed Reset issue and regular maintenance firmware update. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Update maximum continuous operation temperature values for host thermal management and reporting. * Assert fixes, logging enhancements and all current firmware improvements. * Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixed flashing issue through SDR method - Fix to Assert fixes, current firmware improvements and bug fixes. - - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - This component provides support only for VMD enabled Intel VROC platform. - Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Fixed Reset issue and regular maintenance firmware update. - Fixed Reset issue and regular maintenance firmware update. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixes Maximum Temperature Reporting in system log. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS. - - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing. * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform. * Fix NVMe drive component which shows wrong behavior message against the flash result. * Fix SPP force upgrade flash component problem on certain drive family. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Maintenance firmware release to introduce fixes from previous firmware. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Maintenance firmware release to introduce fixes from previous firmware. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Added fix to address a rare case where drive health queries can trigger false drive predictive failure. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 9 - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Update maximum continuous operation temperature values for host thermal management and reporting. * Assert fixes, logging enhancements and all current firmware improvements. * Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Regular Firmware changes included: * corner case performance enhance. * Servo change that resolves issue with early heat application from Idle sweep seek terminated that may cause read errors. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - This component provides support only for VMD enabled Intel VROC platform. - Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Fixed Reset issue and regular maintenance firmware update. - Fixed Reset issue and regular maintenance firmware update. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Firmware addresses a hot plug reporting concern - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Firmware addresses a hot plug reporting concern - Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Assert fixes, logging enhancements and all current firmware improvements and bug fixes. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixed flashing issue through SDR method - A Drive Firmware enhancement has been made for Primera 600 products to reduce the probability of infrequent, unexpected power loss on some backed drives. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Improves data integrity * Decreases possibility of data corruption in certain error and timing conditions * Reduces the probability of hangs - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Improves performance in certain file systems and implements fixes for several of the previous firmware's shortcomings. * The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions. * Several maintenance items are included in this firmware revision that reduce the probability of hangs. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure. * The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events. * Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - This maintenance revision improves data integrity. * The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions. - - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager - Improve the FW about data mismatch after SPL issued. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Fix for unrecovered errors which may occur on the targeted Blocks of Wear-leveling process when host issues Read command. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Fix contains optimization to increase the time for Recovery operation and few checks for maintenance. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Fixes an intermittent issue where the incorrect model number can be reported during spin-up. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - This component provides support only for VMD enabled Intel VROC platform. - Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6. * For more information, CA is published at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us> - Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS. - This component provides support only for VMD enabled Intel VROC platform. - Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6. * For more information, CA is published at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us> - - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Fix contains optimization to increase the time for Recovery operation and few checks for maintenance. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - High Security Enablement support FIPs - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Firmware addresses a hot plug reporting concern - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing. * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform. * Fix NVMe drive component which shows wrong behavior message against the flash result. * Fix SPP force upgrade flash component problem on certain drive family. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing. * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform. * Fix NVMe drive component which shows wrong behavior message against the flash result. * Fix SPP force upgrade flash component problem on certain drive family. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert. * Adding other logging and FW enhancements. - Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert. * Adding other logging and FW enhancements. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Firmware changes aligned for future FIPS code release and one assert fix. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configuratioans. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Fixes the Firmware version HPDB adds compatibility with the latest NAND generation for continuity of supply. - Fixes the Firmware version HPDB adds compatibility with the latest NAND generation for continuity of supply. - Firmware adds support for new humidity sensor - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Regular FW maintenance release. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Improve the FW about data mismatch after SPL - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Fixes a false indication of rare capacitor test failure - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing. * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform. * Fix NVMe drive component which shows wrong behavior message against the flash result. * Fix SPP force upgrade flash component problem on certain drive family. * High Security Enablement support FIPs. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Addresses a hot plug reporting concern * Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Addresses a hot plug reporting concern * Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - High Security Enablement support FIPs - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing. * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform. * Fix NVMe drive component which shows wrong behavior message against the flash result. * Fix SPP force upgrade flash component problem on certain drive family. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Fixed flashing issue through SDR method - Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert. * Adding other logging and FW enhancements. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 10. - Firmware changes aligned for future FIPS code release and one assert fix. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 9. - Firmware contains fix for bug that may cause drive to perform self-initiated reset in systems where maximum queue depth of 128 is exceeded. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - High Security Enablement support FIPs - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Improves data integrity * Decreases possibility of data corruption in certain error and timing conditions * Reduces the probability of hangs and provide a minor performance improvement - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - Improves data integrity. * The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions. * Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide a minor performance improvement. * Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. - This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure. * The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events. * Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Fixes an intermittent issue where the incorrect model number can be reported during spin-up - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Added support for RHEL 9 - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Support firmware flash in OS FIPS enabled mode. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Firmware addresses a hot plug reporting concern - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.. - Added support for RHEL 9. - Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations. * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing. * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform. * Fix NVMe drive component which shows wrong behavior message against the flash result. * Fix SPP force upgrade flash component problem on certain drive family. * Support firmware flash in OS FIPS enabled mode. - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc. - Fixed flashing issue through SDR method - - Initial release - Initial release - Latest FW for PM9A3 drivers - SHA384 fix - SHA384 fix - SHA384 fix - Fixed a BundleUpdate issue for Smart components of size greater than 32MB size. - Ability of HPE iLO to report standard RAS errors for processor, memory, and PCI for HPE Compute ProLiant DL384 Gen12 servers. * Ability of the HPE iLO interface to set and obtain the thermal configuration setting called Smooth Cooling along with the other existing configurations. * Enabled the Compute Utilization Per Second (CUPS) metrics for Intel Sierra Forest processors. This includes CPU, memory, and I/O utilization and CPU power per socket and CPU average frequency per socket. * Added an option using REST API to rotate the ESKM password. * Added IML, Redfish and SNMP alerts to report cases of invalid Power Distribution Board (PDB) on ProLiant DL320 Gen12 platform * Added support for digit validation in PIN based onboarding of iLO to COM - Fixed an issue where param2 check-in challenge_auth response for NVIDIA adapter failed during SPDM authentication. * Fixed an issue where the Kerberos client advertised insecure encryption (RC4, DES) types and rejected the deprecated ones. As a part of this fix, RC4, DES, and 3DES algorithms are removed from the Kerberos requests. * Fixed an issue where the MCTP retry mechanism in i2c communication failed. * Fixed an issue where a low value of the HPE iLO reset progress bar time caused mismatch in the configuration during the HPE iLO reset time. * Fixed an issue where the IPMI fan's pwm values were set to a default of 255 to calculate dutycycle percentage. * Fixed an issue with the time delay between retries for PCIe VDM transmit buffer. * Fixed an issue for the sensor values that were reported in the GET_SENSOR response though these sensors were marked as non-supported in the PDR table. - Renamed the front OCPA and OCPB labeling in REST and HPE iLO UI to OCP Slot A and OCP Slot B. Renamed the rear OCPA and OCPB labeling in REST and HPE iLO UI to OCP Slot A and OCP Slot B. Ability of HPE iLO Redfish to raise a clear event notification for an air filter replacement. Support for Azure Stack HCI 23H2 OS. Adhered to HPE branding guidelines. Addition of HPE ProLiant Advanced License to HPE iLO with HPE Compute Ops Management. Support for the Virtual Media Mount URL length increased to 1023 characters. - Fixed an issue where there was no VSP output on DL360 Gen11 HPE iLO6 due to stack overflow on VSP log buffer handling. Fixed an issue where the memory health status on HPE ProLiant Compute DL384 platforms appeared to be degraded. Fixed an issue where the fan speed was not set as per the thermal configuration due to server device discovery not reaching vMainDeviceDiscoveryComplete. Fixed an issue that did not allow to enable mTLS for subscription and returned error in loading client private key. - Support for SHA2 algorithm with public key authentication method of logging into HPE iLO SSH and is applicable to all security modes. Ability to display the Transceiver Information for the Qualcomm X100 Accelerator. Availability of FRU-data for the Nokia rinline card for identification, discovery, and persistence. Ability to maintain Nokia RINLINE card MCTP-PLDM when the card is nonresponsive . Ability to add 96GB GH200 to HPE ProLiant DL384 Gen11 Server. Support for Domain name server (RDNSS) configuration from Router Advertisements. Support for configuring rsyslog with Transport Layer Security (TLS) using the Redfish interface. Support for TcgEventLogs and HardwareDataBlob in the Redfish ComponentIntegrity. Support for Signed SystemTPM Measurements. Availability of PowerWatts and InputPowerWatts metrics in EnvironmentMetrics and PowerSupplyMetrics schemas. Enhanced the early and critical reminder of air filter change notification range to 30-175 and 30-180. - Fixed an issue that did not allow SNMP packet requests greater than 32 bytes. Fixed an issue where even after an HPE iLO factory default reset and BIOS restoring default manufacturing settings, the DL560 Gen11 server fans were frequently ramping high for short bursts and creating a noise. Fixed an issue where DHE-RSA ciphers are enabled with **Disable Weak Ciphers **and in **High Security **mode setting making HPE iLO vulnerable. Fixed an issue where the get_email_details failed if the user domain name had a **\ **character. Fixed an issue where a PMCI transactional error due to MCTP over I2C communication timed out. Fixed an issue where a certificate import failed on some servers with the **SSL certificate could not be imported since the input certificate is not intended for this server **error. Fixed an issue where HPE iLO6 System Information Storage tab displayed drives without any order. - Enabled RTX 6000 Pro Accelerator on HPE ProLiant DL385 Gen11 servers. Enabled HPE iLO 6 support for NVIDIA RTX A1000 Accelerator. Enabled HPE iLO 6 support for UBM11. Enabled HPE iLO 6 support for fallback sensor enablement or dis-enablement of OCP/PCI card main temperature sensors. Enabled HPE iLO 6 support for NVMe-MI firmware updates. Support for LDAP session persistence. Ability to retain Virtual Serial Port (VSP) logs upon host power cycle. Support for configuring remote syslog with Transport Layer Security (TLS) using the HPE iLO GUI. Added an option to rotate ESKM password from GUI. Added an AC power-cycle as a button in the GUI. Added support to allow boot order modifications during server POST state. Added support to enable or disable fallback temperature sensors for OCP/PCI card. - Fixed an issue of HPE iLO Intelligent Platform Management Interface (IPMI) command (SDR type memory) not listing some of the memory sensor records. Fixed an issue where SFIC generation failed and the URIs in the redfish /v1/ResourceDirectory did not get populated. Fixed an issue where an LDAP/Directory user was unable create a local user. Fixed the repeated characters' issue when Japanese Keyboard Layout is used and Kanji key [English Keyboard ` eq key] was pressed. Fixed an issue where HPE iLO6 Web GUI did not show the correct processor 2 status. Fixed an issue where the OID for power supply redundancy was only returning a value of (1) for Apollo server. Fixed an issue where SSH connections from later versions of PuTTY were not allowed. - Initial Build - This product addresses an issue where network loses IP Address Randomly during AC/DC cycle and idling. - This product addressed abnormal fan behavior when BCM5719 OCP3 installed. * This product addressed the failure of IP dispatch when using BCM5719 LOM as shared iLO networking. * This product addressed that platform might encounter a POST failure when NX1-based controllers and some storage controllers combines. - This product now supports GetPackageStatus NCSI Command. - This product fixed error checking sequence for Firmware Management Protocol API. * This product fixed NC-SI commands to interoperate more benefit with iLO. - This product addresses a problem that might cause a BSOD when trying to reboot the system from operating Windows systems due to NIC internal software mutex problem. * This product addresses an issue where a random missing DHCP IP address occurs when the iLO shared NIC port is used, due to NIC internal software mutex problem. * This product addresses an issue that might cause the POST to get stuck due to NIC internal software mutex problem. - This product enhances libfwupg to improve NVRAM configuration updates. - This product fixes an issue where a dummy Serial Number is seen immediately after update the adapter firmware to version 2.30 (or earlier). * This product fixes an issue where Wake-on-LAN not working is seen. - This product enhances libfwupg to improve NVRAM configuration updates. - This product fixes where MBA configuration reset to defaults after updating firmware. - TBD - This product addresses an issue where the adaters isn't recongized with HPE Ethernet 10Gb 2-port SFP+ OCP3 X710-DA2 Adapter and HPE Ethernet 10Gb 2-port SFP+ X710-DA2 Adapter - This product now supports HPE ProLiant Gen11 Platforms with Intel processors - TBD - This product now supports Red Hat Enterprise Linux 9 Update 1. - This product enhanced the compatibility with the latest drivers. - This product now supports Red Hat Enterprise Linux 9 Update 3. * For more product details, please refer to the latest document in https://www.intel.com/content/www/us/en/download/19622/ - This product enhanced the compatibility with the latest drivers. - This product enhanced the compatibility with the latest drivers. - This product enhanced the compatibility with the latest drivers. - TBD - *Important Notes:** Ver. 1.0.2(C) contains updates to the firmware packaging and is functionally equivalent to ver. 1.0.2. It is not necessary to upgrade with Revision C if a previous component revision was used to upgrade the firmware to version 1.0.2. **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial verison of the firmware. **Known Issues:** None - *Important Notes:** Ver. 1.0.4(C) contains updates to the firmware packaging and is functionally equivalent to ver. 1.0.4. It is not necessary to upgrade with Revision C if a previous component revision was used to upgrade the firmware to version 1.0.4. **Firmware Dependencies:** None **Enhancements/New Features:** Modified the ADC conversion formula based on the new layout design of Gen11 AMD platforms. Improved the accuracy of Fast Platform Triggering mechanism on AMD platforms. **Known Issues:** None - - *Important Notes:** Ver. 1.2.2(C) contains updates to the firmware packaging and is functionally equivalent to ver. 1.2.2. It is not necessary to upgrade with Revision C if a previous component revision was used to upgrade the firmware to version 1.2.2. **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial verison of the firmware. **Known Issues:** None - - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter an SMI storm when PCIe error disconnect recover (EDR) failed. Addressed an issue where the system may fail to update NVMe drive firmware. Addressed an issue where NVMe-oF may not be detected during VMWare installation. Addressed an issue where the system may reboot continuously when PCIE resource need to reallocate. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.4 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update. Addressed an issue where the system may encounter RSOD if NVMe-oF target did not have partitions. Addressed an issue where System Power Supply information in SMBIOS type39 is incorrect when there are more than 2 PSUs. **Known Issues:** None - Added help text for "Smooth Cooling" RBSU option. Added the System Configuration (RBSU) option "PCIe Device Configuration/Advanced PCIe Configuration/PCIe Hot-Plug Error Control" and set to "Hot-Plug Surprise" by default. This setting has the following Redfish property: /redfish/v1/systems/1/bios/settings/PcieHotPlugErrControl - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.4 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where some GPUs may encounter a PCIe lane drop when an NS204i-u is installed. **Known Issues:** None - Updated multi-language translation. Added the help text for RBSU knob "Smooth Cooling". - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.5 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where some options are missing for RBSU knob "Enabled Cores per Processor". Addressed an issue where SMT was not enabled if Enabled Cores per Processor is set to less than 8 cores. Addressed an issue where certain GPU may encounter lane drop issue with NS204i-u installed. Addressed an issue where OCP device cannot be disabled by RBSU. **Known Issues:** None - An IML will be logged if the DIMM serial number is identified as "00000000" - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.6 for AMD 5th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may hang when Microsoft secure-core support is enabled. Addressed an issue where system may hang at RBSU while switch pages in Japanese language. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.G for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where incorrect Structure Boot Name may show in the OS boot option. Addressed an issue where the UUID of HostNqn disappeared after reconfiguring the NVMe-oF initiator name. Addressed an issue where BIOS settings may not be applied while upgrading BIOS and changing BIOS settings at the same time. Addressed an issue where the IML for DIMM mapped out may not be not logged. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter an SMI storm when PCIe error disconnect recover (EDR) failed. Addressed an issue where the system may fail to update NVMe drive firmware. Addressed an issue where NVMe-oF may not be detected during VMWare installation. Addressed an issue where the system may reboot continuously when PCIE resource need to reallocate. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.4 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update. Addressed an issue where the system may encounter RSOD if NVMe-oF target did not have partitions. Addressed an issue where System Power Supply information in SMBIOS type39 is incorrect when there are more than 2 PSUs. **Known Issues:** None - Added help text for "Smooth Cooling" RBSU option. Added the System Configuration (RBSU) option "PCIe Device Configuration/Advanced PCIe Configuration/PCIe Hot-Plug Error Control" and set to "Hot-Plug Surprise" by default. This setting has the following Redfish property: /redfish/v1/systems/1/bios/settings/PcieHotPlugErrControl - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.4 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where some GPUs may encounter a PCIe lane drop when an NS204i-u is installed. **Known Issues:** None - Updated multi-language translation. Added the help text for RBSU knob "Smooth Cooling". - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.5 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where some options are missing for RBSU knob "Enabled Cores per Processor". Addressed an issue where SMT was not enabled if Enabled Cores per Processor is set to less than 8 cores. Addressed an issue where certain GPU may encounter lane drop issue with NS204i-u installed. Addressed an issue where OCP device cannot be disabled by RBSU. **Known Issues:** None - An IML will be logged if the DIMM serial number is identified as "00000000" - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.6 for AMD 5th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may hang when Microsoft secure-core support is enabled. Addressed an issue where system may hang at RBSU while switch pages in Japanese language. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.G for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where incorrect Structure Boot Name may show in the OS boot option. Addressed an issue where the UUID of HostNqn disappeared after reconfiguring the NVMe-oF initiator name. Addressed an issue where BIOS settings may not be applied while upgrading BIOS and changing BIOS settings at the same time. Addressed an issue where the IML for DIMM mapped out may not be not logged. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.D for AMD 4th Generation EPYC processors. **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where System Information\Device Inventory in iLO web may show unknown entries after enabling bifurcation. Addressed an issue where One button secure erase (OBSE) report may show incorrect Drive Port Number and Box Number for MicroChip SR controllers. Addressed an issue where system may become stuck after enrolling many certificates and signatures. **Known Issues:** None - Added new Microsoft Option Rom UEFI CA 2023 secure boot key. Added the "Smooth Cooling" selection to the Thermal Configuration option in the RBSU\Advanced Options\Fan and Thermal Options. This selection modifies the fan speed response to improve acoustics by reducing the rate of fan speed changes. This can improve acoustics for workloads which significantly vary CPU utilization. Note that this option can result in a small reduction in performance due to the short durations of CPU thermal throttling and some operating systems, such as Linux, may log CPU thermal throttling events. These events do not indicate an issue with the system and can be ignored. - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when "RBSU\Network Options\Network Boot Options\IPv6 DHCP Unique Identifier\DUID- LLT" is selected. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where some strings of "NVMe-oF Configuration and Attempt pages" in system RBSU menu are still in English after switching the language to a non-English one. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where the "Server Boot Order" in iLO web is not aligned with "UEFI Boot Order Control" in RBSU. Addressed an issue where an error message in Linux would indicate TCG log size is not compatible. **Known Issues:** None - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter an SMI storm when PCIe error disconnect recover (EDR) failed. Addressed an issue where the system may fail to update NVMe drive firmware. Addressed an issue where NVMe-oF may not be detected during VMWare installation. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Added help text for "Smooth Cooling" in system configuration (RBSU) option. Added the System Configuration (RBSU) option "PCIe Device Configuration/Advanced PCIe Configuration/PCIe Hot-Plug Error Control" and set to "Hot-Plug Surprise" by default. This setting has the following Redfish property: /redfish/v1/systems/1/bios/settings/PcieHotPlugErrControl - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update. Addressed an issue where the system may encounter RSOD if NVMe-oF target did not have partitions. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.G for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where Redfish BIOS settings might not be applied when upgrading the BIOS and changing BIOS settings simultaneously. Addressed an issue where the NVMe-oF target UUID could disappear after modifying the NVMe-oF Initiator name in RBSU. Addressed an issue where an incorrect Structured Boot Name appeared in the OS boot options. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.G for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where Redfish BIOS settings might not be applied when upgrading the BIOS and changing BIOS settings simultaneously. Addressed an issue where the NVMe-oF target UUID could disappear after modifying the NVMe-oF Initiator name in RBSU. Addressed an issue where an incorrect Structured Boot Name appeared in the OS boot options. **Known Issues:** None - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** Removed dynamic power capping support for this release. It is not supported for now. Enabled Spread Spectrum. **Known Issues:** None - Added back dynamic power capping support for B200. - *Important Notes:** Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Swaped PCIe Slot 7 and Slot 8 identifiers. Fixed SMBIOS to support 12 power supplies. **Known Issues:** None - Updated multi-language translation. - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.5 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where some options are missing for RBSU knob "Enabled Cores per Processor". Addressed an issue where SMT was not enabled if Enabled Cores per Processor is set to less than 8 cores. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.5 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where PCIe devices might be missing due to system overheating. **Known Issues:** None - *Important Notes:** This revision of the System ROM includes AMD reference code TurinPI 1.0.0.5 for AMD 5th Generation EPYC processors. This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC processors. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue with temperature reporting for H200. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. Introduced an enhancement to prevent potential system shutdowns caused by specific CPU temperature errors. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. Addressed an unexpected fan control issue that triggered sustained high speeds on Alletra 4120 LFF SKU. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. **Known Issues:** None - Resolved various issues to improve system stability and performance. - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - Added new Microsoft Option ROM UEFI CA 2023 secure boot key. Updated the boot device string rules to include the case when VMD is enabled. Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal Options". - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might detect memory uncorrectable error while system has been idle for extended period of time. Addressed an issue where the system might hang at memory initialization after restoring system setting to factory default. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where some strings of in the System Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are still in English after switching the language to non-English version. Addressed an issue where the NVMe image description in RBSU might be incorrect when VROC is enabled. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where fans might rapidly ramp up and then back down. **Known Issues:** None - Enhanced Chinese and Japanese strings translation support in RBSU pages. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT is selected. Addressed an issue where the system would report Unsupported DIMM Configuration when having 16+0 DIMM mixed rank population. Addressed an issue where the system Consistent Device Naming (CDN) is not working in Windows Server. Addressed an issue where the system memory address translation did not match with system limitation. Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Addressed an issue where the system Max/Min Uncore Frequency value did not be set to default value after loading default settings. **Known Issues:** None. - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when both TXT and TDX are enabled. Addressed an issue where the system might fail to update NVMe drive firmware. Addressed an issue where the system might not be able to detect disk removal via NVMe-oF during VMware installation. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS Settings for FlexRAN v2.0. Added help text for "Smooth Cooling" in system configuration (RBSU) option. - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. Addressed an issue where the Intel PCH model name might be unknown in system configuration (RBSU) -> System information. Addressed an issue where the system might fail to detect EDSFF SED drives with Intel VROC. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel EagleStream IPU2025.3 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.01.04.204.0 (2.60_07_28_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where the system might not be able apply server profile when boot option is enabled for Smart Array Controller. Addressed an issue where the system might be halted at RBSU menu during page switching when working in Japanese language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel Catlow PLR1 guidance. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.02.04.042.0 (1.60_09_05_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where One button secure erase (OBSE) report may show incorrect Drive Port Number and Box Number for MicroChip SR controllers. Addressed an issue where system may stuck after enrolling many certificates and signatures. Addressed an issue where Driver Health Message may show twice in POST when drive is removed and cold boot. Addressed an issue where NS204i may not be identified as NVMe device. Addressed an issue where the virtual serial port may still have message output when the serial port is set to 'Disabled' or 'Physical Port'. **Known Issues:** None - This version always set "RBSU\Power and Performance option\Enhance C state" to "Enabled" to mitigate processor Vmin shift instability issue per Intel's recommendation. Added new Microsoft Option Rom UEFI CA 2023 secure boot key. Added "Smooth Cooling option" in the RBSU\Advanced Options\Fan and Thermal Options. - *Important Notes:** This is the initial version to support Intel Xeon 6300 series processors. This version of the System ROM contains updates aligned with the Intel Catlow Refresh BKC CWL.1.A.4420.00. This version always set "RBSU\Power and Performance option\Enhance C state" to "Enabled" to mitigate processor Vmin shift instability issue per Intel's recommendation. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.03.04.048.0 (2.10_12_03_2024). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where some strings of "NVMe-oF Configuration and Attempt pages" in system RBSU menu are still in English after switching the language to non-English version. Addressed an issue where system RBSU menu might list duplicate or incorrect network interfaces in the selection page. Addressed an issue where the system RBSU menu might not display clear drive location information. Addressed an issue where the "Server Boot Order" in iLO web is not aligned with "UEFI Boot Order Control" in RBSU. Addressed an issue where an error message in Linux would indicate TCG log size is not compatible. Addressed an issue where the "Pending Change light" may be on even if there is no option has been modified in RBSU. **Known Issues:** None - Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss. - *Important Notes:** This version of the System ROM contains updates aligned with the Intel Catlow Refresh BKC CWL.1.A.4420.00. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.03.04.048.0 (2.10_12_03_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the PSU fan keeps running at high speed after system shutdown. Addressed an issue where system may fail to update NVMe drive firmware. Addressed an issue where NvmeOf system may not be detected during VMWare installation. Addressed an issue where the maximum frequency of the processor shows incorrectly after enable or disable Intel Turbo Boost. Addressed an issue where the system would use UUID for IPV6 DHCP when "RBSU\Network Options\Network Boot Options\IPv6 DHCP Unique Identifier\DUID- LLT" is selected. Addressed an issue where the Consistent Device Naming (CDN) may not work. Addressed an issue where the RBSU value is not aligned with the actual C1E setting. Addressed an issue where the system might bring up a warning message ("ERST: [Firmware Warn]: too many record IDs!") in the Linux environment during boot up. Updated SMBIOS type 4 processor max speed to 5700 MHz. Addressed an issue where the PSU fan would keep running at high speed after system shutdown. **Known Issues:** None - *Important Notes:** This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.03.04.048.0 (2.10_12_03_2024). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel Catlow Refresh MR1 BKC. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.03.04.058.0 (2.20_03_03_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update. Addressed an issue where the system may encounter RSOD if NVMe-oF target did not have partitions. **Known Issues:** None - Updated multi-language translation. Added the help text for "Smooth Cooling" RBSU option. - *Important Notes:** This version of the System ROM contains updates aligned with the Intel Catlow Refresh MR1 BKC. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.03.04.058.0 (2.20_03_03_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page. Addressed an issue where the messages of "HPE Intelligent Provisioning" is incorrect for OEM customers. **Known Issues:** None - *Important Notes:** This version of the System ROM contains updates aligned with the Intel Catlow Refresh MR2 BKC. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.03.04.058.0 (2.20_03_03_2025). Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system RBSU setting change might not take effect when the System ROM is being updated. Addressed an issue where the NVMe-oF target UUID might disappear after changing the NVMe-oF Initiator name in RBSU. Addressed an issue where incorrect Structure Boot Name showed in the OS boot option. Addressed an issue where system may hang while switching RBSU pages in multi- language mode. Addressed an issue where the system might encounter "Uncorrectable Machine Check Exception" with "Bank 0x4" during system reboot in SUSE Linux Xen OS environment. **Known Issues:** None - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Best Known Configuration (BKC) WW09. **Firmware Dependencies:** None **Problems Fixed:** Updated Server Platform Services (SPS) Firmware to 06.00.04.033.0 to align with the Intel Best Known Configuration (BKC) WW09. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids. **Firmware Dependencies:** None **Enhancements/New Features:** This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors. **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th Generation Intel Xeon Scalable Processors. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.10 (11/28/2023). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may enter standby mode on Power-On Self-Test (POST) during warm reset cycle. Addressed an issue where system may stop responding at "Memory Initialization - Start" during Power-On Self-Test (POST). **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - Resolved various issues to improve system stability and performance. - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - Resolved various issues to improve system stability and performance. - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Best Known Configuration (BKC) WW09. **Firmware Dependencies:** None **Problems Fixed:** Updated Server Platform Services (SPS) Firmware to 06.00.04.033.0 to align with the Intel Best Known Configuration (BKC) WW09. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids. **Firmware Dependencies:** None **Enhancements/New Features:** This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors. **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th Generation Intel Xeon Scalable Processors. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.10 (11/28/2023). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may enter standby mode on Power-On Self-Test (POST) during warm reset cycle. Addressed an issue where system may stop responding at "Memory Initialization - Start" during Power-On Self-Test (POST). **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - Resolved various issues to improve system stability and performance. - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids. **Firmware Dependencies:** None **Enhancements/New Features:** This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors. **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th Generation Intel Xeon Scalable Processors. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.10 (11/28/2023). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may enter standby mode on Power-On Self-Test (POST) during warm reset cycle. Addressed an issue where system may stop responding at "Memory Initialization - Start" during Power-On Self-Test (POST). **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - Resolved various issues to improve system stability and performance. - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors. **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th Generation Intel Xeon Scalable Processors. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.10 (11/28/2023). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may enter standby mode on Power-On Self-Test (POST) during warm reset cycle. Addressed an issue where system may stop responding at "Memory Initialization - Start" during Power-On Self-Test (POST). **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - Resolved various issues to improve system stability and performance. - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Best Known Configuration (BKC) WW09. **Firmware Dependencies:** None **Problems Fixed:** Updated Server Platform Services (SPS) Firmware to 06.00.04.033.0 to align with the Intel Best Known Configuration (BKC) WW09. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids. **Firmware Dependencies:** None **Enhancements/New Features:** This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors. **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th Generation Intel Xeon Scalable Processors. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel Xeon Scalable Processors and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.10 (11/28/2023). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where system may enter standby mode on Power-On Self-Test (POST) during warm reset cycle. Addressed an issue where system may stop responding at "Memory Initialization - Start" during Power-On Self-Test (POST). **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.20. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.40. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel uPLR3 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.50. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version contains the latest Server Platform Services firmware for 4th and 5th Generation Intel Xeon Scalable Processors. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This version of the SPS should be paired with System ROM 2.60 (08/07/2025) or later. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** This version is in compliance with Intel IPU 2025.3 guidance. **Known Issues:** None - *Important Notes:** None **Firmware Dependencies:** None **Enhancements/New Features:** This is the initial version of the firmware. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for the Intel Raptor-Lake PCH-S based systems. This version of the SPS should be paired with System ROM 1.44 (01/18/2024) or later. **Firmware Dependencies:** None **Enhancements/New Features:** This version contains the latest Server Platform Services firmware for the Intel Raptor-Lake PCH-S based systems. **Known Issues:** None - This version contains the latest Server Platform Services firmware for the Intel Xeon E-2400 series processors. - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for the Intel Xeon E-2400 series processors. This version of the SPS should be paired with System ROM 1.50 (05/16/2024) or later. **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where Intel(R) SPS Firmware may assign duplicate MCTP EIDs for adapters. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for the Intel Xeon E-2400 series processors. This version of the SPS should be paired with System ROM 1.60_09-05-2024. **Firmware Dependencies:** None **Enhancements/New Features:** This version contains the latest Server Platform Services firmware for the Intel Xeon E-2400 series processors. This version is in compliance with Intel PLR1 guidance. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for the Intel Xeon E-2400 series processors. This version of the SPS 06.03.04.048.0 (2.10_12_03_2024) should be paired with System ROM 2.10_12-06-2024. **Firmware Dependencies:** None **Enhancements/New Features:** This version is in compliance with Intel Catlow RPL-E PLR2 and Intel Catlow RPL-E Refresh PV guidance. **Known Issues:** None - This version is in compliance with Intel Catlow RPL-E Refresh MR1 Unify BKC guidance. - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for the Intel Xeon E-2400 series processors. This version of the SPS 06.03.04.058.0 (2.20_03_03_2025) should be paired with System ROM 2.20_03-21-2025. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter reset loop after updating ME/SPS firmware using smart components. **Known Issues:** None - *Important Notes:** This version of the Server Platform Services (SPS) Firmware contains the latest package for the Intel Xeon E-2400 series processors. This version of the SPS 06.03.04.058.0 (2.20_03_03_2025) should be paired with System ROM 2.20_03-21-2025. Details about reported security vulnerabilities and their mitigation can be found at the following link [Security Bulletin Library | HPE Support](https:// support.hpe.com/connect/s/securitybulletinlibrary?language=en_US). **Firmware Dependencies:** None **Problems Fixed:** Addressed an issue where the system may encounter reset loop after updating ME/SPS firmware using smart components. **Known Issues:** None - Initial package which is renamed from i40evf driver - Creating CVL SW1.1 release candidate build. - Add SLES15 SP2 support - This driver fix system freezes when trying to create TCs on VF with no more VSIs available. - Add RHEL8.3 support - Add support to compile on Linux kernel >= 5.9.0 - Added RHEL 6.8 support - Fix the issue of getting crash dump when loading igb module(modprobe igb) - Fix unable to disable the offload property in rhel6u6 - Added SLES12SP2 support - Added RHEL 7.3 support - Added SLES12SP3 support - Added RHEL 7.4 support - Fix for the issue of unable to set MTU value more than 1500 in SUSE12SP3 with Intel NICs - Fixed build on updated kernels of SLES12SP2 - This driver fixes the Spectre/Meltdown issue. - Added SLES15 Support. - Added RHEL6.10 Support. - Added RHEL7.5 Support. - This driver fixes an issue of driver crash with ethtool command. - This driver fixes an issue of Klocwork hits. - Added RHEL7u6 Support. - Added SLES12SP4 Support. - Add SLES15 SP2 support - Add RHEL8.3 support. - v6.1.0 is mainly targeted for iLO 6 1.10 high security state. - Initial package - Fix return values and prints in VF MAC add/del flow - Fix kernel panic after transiting FW LLDP from on to off and restarting lldpad - Fix Throughput lower than expected. - Add SLES15 SP2 support - Add RHEL8u3 support - Add RHEL7u9 support - Addressing the issue of system reboot on unloading iavf driver with maxvfs enabled in switchdev mode - Removed support for RHEL 8U6 - Removed support for RHEL 8U7 - Added support for SLES 15 SP6 - Added support for RHEL 9U4 - Added support for RHEL 8U10 - Removed support for ALP SP0 - Added support for RHEL 9U5 - Added support for RHEL 10u0 - Added support for SLES 15 SP7 - Removed support for RHEL 9U2 - Added support for RHEL 9U6 - Removed support for RHEL 8U6 - Removed support for RHEL 8U7 - Added support for SLES 15 SP6 - Added support for RHEL 9U4 - Added support for RHEL 8U10 - Removed support for ALP SP0 - Added support for RHEL 9U5 - Added support for RHEL 10u0 - Added support for SLES 15 SP7 - Removed support for RHEL 9U2 - Added support for RHEL 9U6 - Removed support for RHEL 8U6 - Removed support for RHEL 8U7 - Added support for SLES 15 SP6 - Added support for RHEL 9U4 - Added support for RHEL 8U10 - Removed support for ALP SP0 - Added support for RHEL 9U5 - Added support for RHEL 10u0 - Added support for SLES 15 SP7 - Removed support for RHEL 9U2 - Added support for RHEL 9U6 - Initial package which is renamed from i40evf driver - Creating CVL SW1.1 release candidate build. - Add SLES15 SP2 support - This driver fix system freezes when trying to create TCs on VF with no more VSIs available. - Add RHEL8.3 support - Add support to compile on Linux kernel >= 5.9.0 - Initial package which is renamed from i40evf driver - Creating CVL SW1.1 release candidate build. - Add SLES15 SP2 support - This driver fix system freezes when trying to create TCs on VF with no more VSIs available. - Add RHEL8.3 support - Add support to compile on Linux kernel >= 5.9.0 - This driver fixes an issue of driver crash with ethtool command. - This driver fixes an issue of Klocwork hits. - Added RHEL7u6 Support. - Added SLES12SP4 Support. - Add SLES15 SP2 support - Add RHEL8.3 support. - This driver fixes an issue of driver crash with ethtool command. - This driver fixes an issue of Klocwork hits. - Added RHEL7u6 Support. - Added SLES12SP4 Support. - Add SLES15 SP2 support - Add RHEL8.3 support. - Initial package - Fix return values and prints in VF MAC add/del flow - Fix kernel panic after transiting FW LLDP from on to off and restarting lldpad - Fix Throughput lower than expected. - Add SLES15 SP2 support - Add RHEL8u3 support - Add RHEL7u9 support - Addressing the issue of system reboot on unloading iavf driver with maxvfs enabled in switchdev mode - Initial package - Fix return values and prints in VF MAC add/del flow - Fix kernel panic after transiting FW LLDP from on to off and restarting lldpad - Fix Throughput lower than expected. - Add SLES15 SP2 support - Add RHEL8u3 support - Add RHEL7u9 support - Addressing the issue of system reboot on unloading iavf driver with maxvfs enabled in switchdev mode - Use one spec for KMP and non-KMP OS's. - Add QoS utils. - Renamed kernel-ib package to mlnx-ofa_kernel-modules - Use one spec for KMP and non-KMP OS's. - Add QoS utils. - Renamed kernel-ib package to mlnx-ofa_kernel-modules - Use one spec for KMP and non-KMP OS's. - Add QoS utils. - Renamed kernel-ib package to mlnx-ofa_kernel-modules - 10.02.14.00-k1 AG 05/21/2025 - - 10.02.14.00.a4-k1 AG 02/27/2025 [FCD-4186] : Device discovery fails on continuous reboot (Hitachi) Resolution : In a fabric topo when there is mismatch in state of login between driver and FW, query FW again and proceed with login Scope : 27xx/28xx Adapters [FCD-XXX] : Make functions local to a file static Resolution : Make functions local to a file static Scope : 27xx, 28xx series Adapters [FCD-XXX] : Remove unused function Resolution : Function qla25xx_set_purex is unused - remove it Scope : All adapters [FCD-4729] : Compilation errors with Sles15sp6 Resolution : Fix compilation errors on Sles15 SP6 Scope : Series Adapters [FCD-4536] : Compilation errors on RHEL10 Resolution : RHEL 10 has rebased to the latest kernel resulting in several build issues. Fix them and ensure that it builds on older kernels as well. Scope : Series Adapters [FCD-4676] : Add support for RH 9.6 (compilation) Resolution : Fix compilation errors on RH 9.6 Scope : Series Adapters [FCD-XXX] : Update README to reflect the supported distros Resolution : Update README to reflect the supported distros Scope : All Adapters Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com> Change-Id: Ic4af035fd48a3137923c7d3590be4271b0a7fd32 commit e22ea0921e20bcf93db0fae2b8dd579005686908 Author: Anil Gurumurthy <agurumurthy@marvell.com> Date: Fri Jan 10 11:06:14 2025 +0530 qla2xxx: Update driver version to 10.02.13.03-k1. - 10.02.13.03-k1 AG 01/10/2025 [FCD-4627] : HPSD5.10-BFS RHEL9.5 system crash on Nimble-HF40 failover test. Resolution : Check for sp being valid, before freeing associated memory Scope : All - 10.02.13.02-k1 MR 01/07/2025 [FCD-4657] : Fix SCSI INQ issue for supporting T10 DIF. Resolution : Replace sp completion with qpair completion call.. Scope : 28XX - 10.02.13.01-k1 MR 01/02/2025 [FCD-1040] : Call scsi done and nvme done with good completion without lock. Resolution : Done changes to move scsi done and nvme done without lock. Scope : 27xx and above - 10.02.13.00-k1 AG 10/22/2024 - - 10.02.13.00.a3-k1 SD 10/09/2024 [FCD-XXX] : Crash seen during load/unload test in a loop Resolution : Delay module unload when there is a fabric scan going on Scope : All adapters [FCD-4193] : SCSI device never recovers after RSCN Resolution : Remove tape specific checks which prevented recovery Scope : All adapters - 10.02.12.01-k1 MR 05/29/2024 [FCD-3465] : Server got crashed while running port toggle test. Resolution : During vport_delete send async_logout explicitly. Scope : 28XX - 10.02.12.00-k1 SD 05/20/2024 - - 10.02.12.00.a5-k1 SD 05/07/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a4-k1 SD 04/25/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a3-k1 SD 03/15/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : SFP cache on legacy adapter Scope : all - 10.02.12.00.a2-k1 SK 02/08/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : Fix NVME + NPIV connect issue Resolution : Initialize irq offset Scope : ALL - 10.02.12.00.a1-k1 QT 01/09/2024 scsi: qla2xxx: Drop redundant pci_enable_pcie_error_reporting() Resolution : Fix RHEL 9.4 compile issue Scope : ALL [FCD-3515] : API support for SFP data cache Scope : 27xx, 28xx [FCD-xxx] : Fix SLES15.6 compile issue Resolution : Remove stale fields Scope : ALL [FCD-3634] : Remove check req_sg_cnt should be equal to rsp_sg_cnt. Resolution : Firmware supports multiple sg_cnt for request and response for CT commands, so remove the redundant check. Scope : All Adapters [FCD-717] : Move FCE Trace buffer allocation to user control Resolution : Modify existing DFS knob to allow user to enable|disable this feature. Scope : Any [FCD-xxx] : Remove del_work work from qla_schedule_sess_for_deletion. Resolution : Remove del_work work from qla_schedule_sess_for_deletion. Scope : All [FCD-xxx] : Additional target mode code cleanup. Resolution : Additional target mode code cleanup. Scope : All [FCD-xxx] : Update copyright information. Resolution : Update copyright information. Scope : All [FCD-xxx] : Remove target code from qla_target files. Resolution : Remove target code from qla_target files. Scope : All [FCD-xxx] : Remove target mode code from initiator specific files. Resolution : Remove target mode code from initiator specific files. Scope : All [FCD-xxx] : Move common code to initiator specific files. Resolution : Move common code to initiator specific files. Scope : All [FCD-3751] : Fix use after free on unload Resolution : Remove duplicate signals on freeing dpc_thread Scope : ALL [FCD-3515] : Caching SFP data Scope : 27xx, 28xx [FCD-xxx] : Exec FW with delay Resolution : Add delay before command retry Scope : 28xx [FCD-xxx] : fix abort in bsg timeout Resolution : Wait for bsg to return before abort exit Scope : ALL [FCD-xxx] : Use QP lock to search for bsg. Resolution : use correct lock to protect search Scope : ALL [FCD-xxx] : Remove SQ in queuecommand Resolution : Remove duplicate code. Scope : ALL [FCD-xxx] : Reduce fabric scan duplicate code. Resolution : Consolidate routines that handle GPNFT & GNNFT. Scope : ALL [FCP-743] : Remove ql2xstay_attach_on_load_failure Resolution : Remove driver parameter used as part of feature test. Scope : 27xx, 28xx - 10.02.11.00-k1 NJ 10/25/2023 [FCD-xxx] : Remove PCI ID 0x2971 Resolution : Remove PCI ID 0x2971 Scope : [FCD-3661] : Remove 8031 from deprecate and unmaintained list. Resolution : Remove 8031 from deprecate and unmaintained list. Scope : 8031 [FCD-3571] : Unable to resume FW dump collection Resolution : send notification to udev Scope : 27xx, 28xx [FCD-3631] : Convert Port disable state to maintenance mode Resolution : Rename state and turn flag indicator Scope : 27xx + 28xx - 10.02.11.00.a8-k1 NJ 10/13/2023 [FCD-3632] : Remove support for FCoE device ids. Resolution : Remove FCoE ids from pci table. Scope : 8xxx [FCD-3624] : Fix optrom version displayed in FDMI Resolution : Populate EFI version Scope : Series Adapters [FCD-3632] : Remove CNA reference from README. Resolution : Remove CNA reference from README. Scope : 8xxx - 10.02.11.00.a7-k1 NJ 09/22/2023 [FCD-3195] : Fix flash read failure Resolution : Check return code for each flash read. Scope : Series Adapters [FCD-3571] : System flood by fw dumps Resolution : udev script to pause fw dump collection Scope : Any [FCD-3566] : Limit FW dump improvement to 27xx + 28xx Resolution : Add filter for 27xx + 28xx adapters Scope : 27xx+ [FCD-3497] : Return ENOBUFS if sg_cnt is more than one for ELS cmds. Resolution : This error is because FW support single sg element for ELS Pass-through IOCB (0x53h). This particular error code will help API and Apps to display appropriate message to the user. Scope : All Adapters [FCD-3510] : RHEL & SLES OOB driver request: deprecate L8/Hilda HW Resolution : Added a frame work to display the message based on device and OS. Scope : L8 and L16 (Hilda and CNA) [FCD-3269] : Init Control Block is dereferenced incorrectly Resolution : Correctly dereference ICB Scope : 20xx [FCD-3421] : Add Support to collect fw_dump on system crash or panic. Resolution : Add Support to collect fw_dump on system crash or panic Scope : 27xx, 28xx - 10.02.11.00.a6-k1 MR 09/08/2023 [FCD-XXX] : Modify error code handling for sfp fw upgrade mbx. Resolution : Modify error code handling for sfp fw upgrade mbx. Scope : 28xx [FCD-XXX] : Block sysfs resets and fw_dump during sfp fw upgrade Resolution : Block sysfs resets and fw_dump during sfp fw upgrade Scope : 28xx [FCP-743] : Block sysfs access during maintenance mode Resolution : Add check for maintenance mode. Scope : Any [FCD-3506] : Fix double free of dsd_list during driver load. Resolution : add pointer check before access Scope : Any - 10.02.11.00.a5-k1 MR 08/18/2023 [RH BZ 2039422] : NVMe-FC kernel crash during reload driver test Resolution : validate nvme_local_port correctly Scope : Any [FCD-XXX] : Fix for potential Null pointer dereferenced Resolution : Check before dereferencing pointer Scope : Any [FCP-743] : Enable driver attach to bad HW Resolution : turn on ql2xstay_attach_on_load_failure option Scope : 27xx, 28xx - 10.02.11.00.a4-k1 MR 08/11/2023 [FCD-xxx] : Update README file for zio information Resolution : Update readme file with zio information Scope : Any [FCD-3415] : Std-DIF is not working with HPe K1 driver Resolution : Reset the protect bit in the INQ response only when pDIF is enabled and negotiated. Scope : 26xx/27xx/28xx - 10.02.11.00.a3-k1 AG 08/03/2023 [FCP-743] : Allow only selective BSG requests in maintenance mode Resolution : Allow certain BSG to go through during maintenance mode Scope : Any [FCP-743] : FW dump improvement Resolution : Improve data capture Scope : 27XX, 28XX [FCD-3252] : Unable to act on RSCN for port online. Resolution : Clear RSCN flag only when driver is acting on the notification Scope : Any [FCD-xxx] : 32 Bytes CDB Resolution : Use Type 6 IOCB for CDB bigger than 16Bytes Scope : Any Unit Test : i) force IO to use Type6 only for over the weekend run. ii) force error path(s) to make sure no crash. [FCD-xxx] : Move resource to allow code reuse. Resolution : relocate dsd_list to qpair Scope : Any - 10.02.11.00.a2-k1 AG 07/27/2023 [FCD-3411] : CS_DMA Error observed while running DIF IO Resolution : While running DIF enabled IO, a CS_DMA error was observed. A FW dump is needed to better debug this. So take a FW dump on encountering this. Scope : 27xx/288 series of adapters [FCD-3406] : Modifiy default zio threshold value. Resolution : Modifiy default zio threshold value. Scope : 27xx/28xx Series Adapters [FCD-3314] : Delay IO Abort on PCI error Resolution : On detection of PCI error, allow IO's to wind down. Scope : Any [FCD-3314] : Fix system crash due to bad pointer access Resolution : Check SRB type before access. Scope : 27xx+ - 10.02.11.00.a1-k1 AG 07/14/2023 - FCP-749: qla2xxx: Add support for build for RH 9.3 and RH 8.9 distro Resolution : Build on RH 9.3 was failing owing to change of definition of fc_host_fpin_rcv and removal of DID_TARGET_FAILURE. Fix part of it by updating to latest upstream code. Scope : 27xx/28xx series of adapters - FCD-3302 : During unload Error detected messages is seen. Resolution : Change the wording of the message as its not an error. Scope : Series Adapters - FCD-3293 : Initiator sever getting crashed after LOGO. Resolution : Fix double free of fcport Scope : Any - Revert "scsi: qla2xxx: Change default ZIO threshold." This reverts commit 8812bcc1b7a25494ec8755ff3b61412a9993ff5b. The ZIO threshold now is 64. - FCD-xxx : Fix unreachable code Resolution : Remove dead code Scope : 28xx+ - FCD-3232 : Potential risk of double free pointer detected in Coverity scan by ran by Citrix Resolution : NULL the pointer after first free. Scope : All - 10.02.10.00-k1 SK 06/14/2023 Non-alpha build - 10.02.10.00.a2-k1 BH 05/12/2023 - FCD-3140: qla2xxx: Fix command flush on cable pull. Changes: Add wait for commands to return. - FCD-XXX: qla2xxx: NVME|FCP prefer flag not being honored. Changes: Reread prefer flag on chip reset - FCD-XXX: qla2xxx: Update readme file - 10.02.10.00.a1-k1 BH 05/02/2023 - FCD-XXX: qla2xxx: Update Copyright Changes: Update Copyright for Marvell. - FCD-XXX: qla2xxx: Update manufacturer detail Changes: Update manufacturer detail to "Marvell" - FCD-3140: qla2xxx: Host crash during StressAndHostPortReset test Changes: Remove unused nvme_ls_waitq wait queue. - FCD-XXX: qla2xxx: [RH-BZ 2167274]: Wait for io return on terminate rport. Changes: dd wait to terminate_rport_io - 10.02.09.00.a11-k1 BH 03/27/2023 - FCD-XXX: qla2xxx: Add link down + logo rx stat counts Changes: Add counters to track link down and Logo receive. - 10.02.09.00.a10-k1 BH 03/17/2023 - FCD-XXX: qla2xxx: Support for update SFP firmware of ACCELINK Changes: [New Feature] Support for update SFP FW of ACCELINK WTD 64G - FCD-717: qla2xxx: Split FCE|EFT trace control Changes: Split buffer alloc and enable of feature into individual step. - BZ-2093878: qla2xxx: perform lockless command completion in abort path Changes: Perform lockless command completion in abort path - 10.02.09.00.a9-k1 BH 03/06/2023 - FCD-2390: qla2xxx: Fix N2N stuck connection. Changes: Clear the blocking flag. - FCD-2496: qla2xxx: Prevent command send on chip reset Changes: Check for chip reset before sending IOCB. - FCD-2035: qla2xxx: Fix mem access after free. Changes: Remove access of memory - FCD-2720: qla2xxx: Move cmd_to_req_q latency counter before processing response. - FCD-XXX: qla2xxx: Update readme file for current program - 10.02.09.00.a8-k1 BH 02/27/2023 - FCD-2585: qla2xxx: Remove unsupported ql2xenabledif option. Changes: Removed unsupported ql2xenabledif=1 option and validate the user input. - FCD-2305: qla2xxx: Error code did not return to upper layer Changes: Preserve error code from TMF and return it to upper layer. - FCD-2035: qla2xxx: fix inconsistent TMF timeout. Changes: Allow TMF error to return to upper layer without session tear down. - FCD-2035: qla2xxx: Fix TMF leak through. Changes: Check for chip reset or session change before sending Task management. - 10.02.09.00.a7-k1 BH 02/17/2023 - FCD-2858: qla2xxx: USCM: Check for vp_idx before setting EDC and RDF set flags. Changes: Add check for vp_idx before setting EDC and RDF set flags when processing RIDA. Revert patch: - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition. - 10.02.09.00.a6-k1 BH 02/13/2023 - FCD-2750: qla2xxx: IO's are failing on Standard DIF enabled 3PAR LUN Changes: Revert an offending patch and work on an issue with upstream. - 10.02.09.00.a5-k1 BH 02/06/2023 - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition Changes: Remove EDC and RDF set flags on Report ID Acquisition. - FCD-2879: qla2xxx: Compilation errors on SLES15SP5 Beta3-202301 Changes: Write generic code to find tag of scsi cmnd - FCD-2846: qla2xxx: Correct bsg_reply size in bsg interface Changes: Fix the bsg_job->reply_len with size of "struct fc_bsg_reply" - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the invariant expression in the condition - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the expression flogi_acc_pld_remaining == 0 - FCD-XXXX: qla2xxx: Changes of logs level for SFP temperature monitoring - 10.02.09.00.a4-k1 BH 01/29/2023 - FCD-2308: qla2xxx: Add bsg call to read port information Changes: Add bsg interface to allow app to read remote port information. - FCD-XXX: qla2xxx: KW-97439: unreachable code Changes: Return void if return value is not needed - FCD-XXX: qla2xxx: Add logs for SFP temperature monitoring Changes: Add debug log for Temperature Alert (8070h) Asynchronous Event - 10.02.09.00.a3-k1 BH 01/19/2023 - FCD-XXX: qla2xxx: Add support of RHEL9.2 - FCD-XXX: qla2xxx: Add support of RHEL8.8 - FCD-XXX: qla2xxx: Add support of SLES15 SP5 - FCD-2800: qla2xxx: Add support of OpenEuler-22.03 - 10.02.09.00.a2-k1 BH 01/10/2023 - FCD-XXX: qla2xxx: kw: unreachable code, SRB type is 0 just before latency counter incremented. Changes: SRB type is 0 just before latency counter incremented. - FCD-XXX: qla2xxx: kw: reset current_topology much later Changes: Reset current_topology much later on detecting - FCD-XXX: qla2xxx: kw: unreachable code, CS_COMPLETE is 0 and its already checked. Changes: Remove unreachable - FCD-XXX: qla2xxx: kw: Checking for port_state always yields zero Changes: Instead of bitwise AND check for port_state directly - FCD-1569: qla2xxx: Fix fw resource tracking Changes: Use global counter - FCD-XXX: qla2xxx: [ER-144639]: Flush mailbox commands on chip reset Changes: Use lock to prevent race condition. - FCD-2735: qla2xxx: USCM-VL: NVRAM VL disabled logins with extend FLOGI (VL enabled) Changes: Reset the spl. features control block flag to avoid logging in with ER_RDY. - FCD-XXX: qla2xxx: klockwork: Fix buffer over flow Changes: Use correct buffer size. - FCD-XXX: qla2xxx: EDIF: kw: remove unnecessary bit field - FCD-2563: qla2xxx: Turn off noisy message log. - FCD-XXX: qla2xxx: kw: remove dead code in qla24xx_config_rings - 10.02.09.00.a1-k1 BH 01/10/2023 - FCD-717: qla2xxx: allow FW dump extraction if load fail Changes: Add knob to force driver to stay attached to the fail adapter. - FCD-717: qla2xxx: Initialize FW buffer size with seed value Changes: Initialize FW Buffer size with seed value - FCD-XXX: qla2xxx: klockwork: Remove QLA_COMMAND_ERROR check in qla2x00_execute_fw. Changes: Remove the unnecessary QLA_COMMAND_ERROR check - FCD-2390: qla2xxx: Fix session hang in gnl Changes: Clear this flag to prevent blockage. - FCD-2390: qla2xxx: Fix erroneous link up failure Changes: Set fw_started flag early to prevent interrupts being dropped - FCD-2496: qla2xxx: Fix command flush during TMF Changes: Wait for commands flush before closing TMF - FCD-2035: qla2xxx: Limit TMF to 8 per function Changes: Limit TMF to 8 per function - FCD-XXX: qla2xxx: Add NVMe Disconnect support. Changes: Add support for NVMe Disconnect feature. - FCD-XXX: qla2xxx: Modify qla27xx_copy_fpin_pkt to support PURLS IOCB. Changes: Modified qla27xx_copy_fpin_pkt to support both PUREX and PURLS IOCBs. - FCD-717: qla2xxx: Adjust iocb resource on qpair create Changes: Add call to readjust iocb + exchange limit. - FCD-2390: qla2xxx: Fix deletion race condition Changes: Move check field behind lock - FCD-XXX: qla2xxx: klockwork: Pointer checked for NULL at linx x will be dereferenced at linx x+y. Changes: Remove the unnecessary Null check. The pointer will likely be valid. - FCD-XXX: qla2xxx: Observed call trace in smp_processor_id() with debug kernel Changes: Use raw_smp_processor_id API - FCD-2275: qla2xxx: USCM: Cleanup code related to IOPS based throttling Changes: IOPS and BW based throttling is not used. Remove those code. - FCD-2273: qla2xxx: USCM: Code cleanup w.r.t module params (ql2x_scmr_flow_ctl_tgt, ql2x_scmr_flow_ctl_host) Changes: Remove the redundant module parameters - FCD-2408: qla2xxx: USCM: Driver doesn't honor the adapter port Restore Default Settings Changes: Update the nvram values to the host as well as fcport - FCD-2363: qla2xxx: USCM: Slow Queue usage changes Changes: Use Slow queue only under specific scenarios - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Don't increment the counter for under-run. - FCD-2291: qla2xxx: Erroneous link down. Changes: Allow adapter reset to complete before discovery - FCD-2035: qla2xxx: Fix hang in task management Changes: Bail out of TMF on error - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path - FCD-XXX: qla2xxx: USCM: Debug log message improvement Changes: Log target WWPN for peer congestion - FCD-2164: qla2xxx: Fix stall session after app start Changes: Use session delete to avoid the accidental clearing of scan_flag - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Check fcport state before invoking the mailbox - FCD-XXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: Set throughput baseline on 1st FPIN - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix parsing the fpin when multiple descriptors are present - FCD-XXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCD-XXX: qla2xxx: USCM: Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: Fix for KW-97392 Changes :Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: Remove dead code - flagged by klocwork - FCD-847: qla2xxx: fixup: Fix exchange over subscription. - FCD-2434: qla2xxx: Fix crash when IO abort times out - FCD-XXX: qla2xxx: Rearrange scm rx path handling code. - 10.02.08.01-k1 BH 09/28/2022 - FCD-2392: Fix initrd image creation failure in OpenEuler, Kylin and UOS Changes: Add support for creating initrd image on openEuler, Kylin and UOS - 10.02.08.00-k1 BH 09/16/2022 - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Residual under-run is not an interface error, hence no need to increment that count. - FCD-2291: qla2xxx: Fix erroneous link down. Changes: Allow adapter reset to complete before any scan can start. - FCD-2035: qla2xxx: Fix hang in task management Changes: Add additional error check at various point - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced. - 10.02.08.00.a7-k1 BH 08/22/2022 - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path. - FCD-2164: qla2xxx: USCM: Fix stall session after app start Changes: Prevent accidental clearing of flag that blocks re-login - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset. - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Heck fcport state before invoking mailbox - FCDXXX: qla2xxx: USCM: Debug log message improvement - 10.02.08.00.a6-k1 BH 08/09/2022 - FCDXXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: if VL switchreduces the throughput below 50%, we would not throttle any further. - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix the FPIN parsing to take into account multiple descriptors. - FCDXXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCDXXX: qla2xxx: USCM:Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..10 - 10.02.08.00.a5-k1 BH 07/29/2022 - FCD-XXX: qla2xxx: klocwork: Possible Null Pointer Dereference Changes: Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: USCM: Fix mqueuecommand return code during throttle down request. - FCD-XXX: qla2xxx: Revert klockwork: Fix buffer overrun - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h - FCD-2035: qla2xxx: Fix Task Mgmt Cmd fail due to unavailable resource Changes: Limit TM commands to 8 per target. - 10.02.08.00.a4-k1 BH 07/23/2022 - FCD-847: qla2xxx: Fix exchange over subscription. Changes: check for exchange availability before command submission - FCD-XXX: qla2xxx: Remove unintended flag clearing Changes: Remove unintended flag clearing. - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h Changes: Add wait for completion of Marker! - FCD-XXX: Fix performance dip due to lock contention Changes: Save the allocated memory for reuse and avoid the lock - FCDXXX: qla2xxx: USCM: Do not send EDC and RDF for NPIV ports Changes: Disable sending USCM ELS for vports - FCDXXX: qla2xxx: USCM: VL: Do not set target speed to 1G for slow lane Changes: Do not set the target speed while changing lanes. - FCD-2012: qla2xxx: Throttling up messages seen when profile is changed Changes: Set the new profile for each fcport (along with the host). - FCD-XXX: qla2xxx: USCM: VL - Clean up FLOGI_ACC parsing Changes: structure that could be used to parse the FLOGI_ACC by using offsets - FCD-1990: qla2xxx: Fix nvram load config error Changes: Remove re-definition of port flags while enabling virtual lane support - FCD-XXX: qla2xxx: USCM:VL, I/O does not move back to the normal lane Changes: Check if I/O throttling is being done, before deciding to move the normal lane. - FCD-XXX: qla2xxx: Fix stall login Changes: Reset session state to allow relogin logic to re-drive the connection. - FCD-847: qla2xxx: Fix exchange over subscription for mgt cmd. Changes: would check for exchange availability before command submission. - FCD-847: qla2xxx: Fix exchange over subscription. Changes: would check for exchange availability before command submission. - FCD-XXX: qla2xxx: relocate/rename vp map. - FCD-XXX: qla2xxx: Klocwork: Fix for Unexpected type of a scan function parameter - 10.02.08.00.a3-k1 BH 07/01/2022 - FCD-1818: qla2xxx: Fix call trace in debug kernel due to missing spinlock init Changes: Fix the call trace by initializing trace lock. - FCD-1923: qla2xxx: USCM: VL - After disabling VL via CLI, status shows "Non-operational" Changes: Return VL status appropropriately - FCD-1922: qla2xxx: Fix discovery issues in FC-AL topology Changes: Checks FC loop map when Get ID list returns no device - FCD-1831: qla2xxx: Fix link failure in NIPV environment. Changes: Remove NPIV host from directly being able to chip reset. - FCD-XXX: qla2xxx: Fix DMA-API call trace on NVME LS requests with debug kernel Changes: Remove DMA mapping from the driver - FCD-XXX: qla2xxx: Fix KASAN use-after-free warning in qla24xx_sp_unmap Changes: Remove stale fcport access in qla2x00_rel_sp - FCD-XXX: qla2xxx: Fix KASAN out-of-bounds warning in qla_update_sp Changes: Size for memcpy was corrected to use the right length. - FCD-XXX: qla2xxx: Fix imbalance vha->vref_count Chnages: Add an extra ref count for the task management paths. - FCD-XXX: qla2xxx: Tweak Latency measurement Changes: Move the time read further ahead to the start of queuecommand and later to the point where it is just before scsi_done. - FCD-XXX: qla2xxx: klockwork: Silent superfluous warning. Changes: Remove superfluous Null check. - FCD-XXX: qla2xxx: klockwork: Fix buffer overrun Changes: Replace structure name to allow proper size calculation - FCD-XXX: qla2xxx: Remove dead code (GNN ID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code (GPNID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code. Changes: Removing drport field and FCPORT_UPDATE_NEEDED, and EDIF_TICK_NEEDED signals - FCD-XXX: qla2xxx: Do not select slow queue if USCM is enabled Changes: Do not select slow queue whilie initializing cpu map - FCD-XXX: Select HW queue depending on Tx CPU Changes: Select qpair which is in correlation with Tx CPU - FCD-XXX: qla2xxx: Add support for displaying I/O throttle information Changes: Display the driver I/O throttle information along with VL information - FCD-XXX: qla2xxx: USCM: Throttle only R/W commands for NVME Changes: Throttle only read/write IOs. - Bring back following reverted changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.08.00.a2-k1 BH 06/19/2022 - FCD-XXX: qla2xxx: klockwork - Check valid rport returned by fc_bsg_to_rport Changes: Check valid rport returned by fc_bsg_to_rport - FCD-XXX: qla2xxx: klockwork - Check for a valid fcport pointer Changes: Add a check for a valid fcport pointer at the time of exit - FCD-XXX: qla2xxx: klockwork - Move fcport NULL check to avoid dereference Changes: Move the fcport NULL check to avoid the dereference. - FCD-1883: qla2xxx: USCM: Adapter shows "RDF Complete" when Link is down Changes: Reset the flag, so that when USCM is negotiated, the CLI shows the correct status - FCD-1846: qla2xxx: USCM: A log message while clearing stats Changes: Add a log message while clearing USCM stats - FCD-XXX: qla2xxx: USCM: VL-Reset FC device virtual lane priority to normal on a port flap Changes: Reset the virtual lane to normal on a port flap, ISP reset - FCD-XXX: qla2xxx: USCM: VL-Set target congestion before switching lanes Changes: Set the target state before the lane switch. - FCD-1752: qla2xxx: USCM: VL-Sysfs does not show Virtual Lane as enabled Changes: extended flogi_acc can also be parsed correctly. - FCD-1652: qla2xxx: Check if port is online before sending ELS Changes: Check if port is online before sending ELS - FCD-XXX: scsi: qla2xxx: Synchronize rport dev_loss_tmo setting - 10.02.08.00.a1-k1 BH 05/27/2022 - FCD-XXX: qla2xxx: USCM: Virtual Lane, Fix PUN handling Changes: Have a default priority range for each lane and ensure that the range is programmed correctly - FCD-XXX: qla2xxx: USCM: Support for Virtual Lanes Changes: Enable Virtual Lane support for Cisco switch - 10.02.07.00-k1 BH 05/27/2022 - Non-alpha build - 10.02.07.00.a19-k1 BH 05/21/2022 - FCD-XXX : qla2xxx: USCM: Throttling is not honored for NVMe Changes: Enable NVMe READ/WRITE commands to be throttled - FCD-XXX: qla2xxx: USCM: Add counters to track directional throttling Changes: Add sysfs counters to have stats displayed for busy status returns. - FCD-1801: qla2xxx: USCM: CP reads go to zero while doing directional throttling Changes: Take into account the directional queue depth while returning a busy status to the stack. - FCD-1809: qla2xxx: USCM: Restoring USCM Profile to default result in driver - FCD-1798: qla2xxx: USCM: Profiles are not honored for peer congestion Chnages: Apply the profile to each target (fcport) when the profile is changed. Reverting the following changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.07.00.a18-k1 BH 05/12/2022 - FCD-1484: qla2xxx: Manufacturer details should be "Marvell Semiconductor, Inc." Changes: Update Manufacturer details to indicate Marvell Semiconductors - FCD-XXX: qla2xxx: USCM: Throttle only read and write commands Changes: Throttle only read and write commands. - FCD-XXX: qla2xxx: USCM: Do not clear throttle for Clear Cong FPIN. Changes: Do not clear throttle when Clear Congestion FPIN is received. - FCD-XXX: qla2xxx: USCM: Change default profile to Monitor Changes: Set the default throttle profile as Monitor. - FCD-XXX: qla2xxx: Fix few issues reported by klocwork tool - 10.02.07.00.a17-k1 BH 05/06/2022 - FCD-1522: qla2xxx: USCM: Throughput drops to zero in Monitor mode Changes: Restore qdepth based on monitor mode - FCD-1315: qla2xxx: Fix erroneous mailbox timeout after pci error inject. Changes: Clear wait for MB interrupt flag to prevent stale MB completion arriving - FCD-1424: Remove verbose IO debug messages Changes: Remove the IOCB debug messages for every IO - FCD-XXX: Support for NVMe parameters in Auxiliary Image Status Changes: Added new structure member, bit define and image status check. - 10.02.07.00.a16-k1 BH 04/08/2022 - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - FCD-1221: qla2xxx: USCM: Switch does not send FPINs after a EDC re-negotiation Changes: Send Link Service Request Information wih the EDC response, along with the other descriptors. - 10.02.07.00.a15-k1 BH 03/25/2022 - FCD-1249: qla2xxx: edif: Fix dropped IKE message. Changes: Fixes IKE message being dropped due to error in processing Purex IOCB and Continuation IOCBs. - FCD-1457: qla2xxx: Zero undefined mailbox IN registers Changes: Set zero to unuse register's value while requesting a new MB command. - FCD-1425: qla2xxx: USCM: Seconds since last event showing incorrect value Changes: Calculate delta time correctly - FCD-1287: qla2xxx: Fix incorrect display of max frame size. Changes: Save off the field of interest into separate location and convert into words. - FCD-XXX: qla2xxx: Fix memory leak when reading tgt_port_database debugfs file - FCD-XXX: qla2xxx: USCM: Do not reset SCM stats on a link bounce/ISP reset - 10.02.07.00.a14-k1 BH 03/14/2022 - FCD-XXX: qla2xxx: Fix losing FCP-2 targets on long port disable with IOs Changes: Fix this by accepting RSCN when the device is not online. - FCD-XXX: qla2xxx: Fix losing target when it reappears during delete Changes: Fix the issue by adding state checks before proceeding. - FCD-XXX: qla2xxx: Fix losing FCP-2 targets during port perturbation tests Changes: Fix was to ignore delete for FCP-2 devices in certain sequence. - FCD-119: qla2xxx: Fix crash due to stale srb access around IO timeouts Changes: Ensure srb is either returned during error IO timeout error escalation. If that is not possible fail the escalation path. - FCD-1132: qla2xxx: HPE3PAR: Fix IOCB resource count leak Changes: Decrement FW IOCB resource count. - FCD-1132: qla2xxx: Turn off MQ for 8G adapter. Changes: For 8G adapter, multi queue was enabled accidentally. - FCD-1385: Wind down adapter after pcie error. Changes: Detect the PCIE error and returns all IO's to upper layers. - FCD-1412: qla2xxx: Reset Congestion Warning/Alarm signals count. Changes: Reset signals at every signal check boundary (1 sec). - 10.02.07.00.a13-k1 BH 02/17/2022 - FCD-1353: qla2xx: a12/a11 driver compilation gives warning messages Changes: Fix the fall through warning - FCD-1342: qla2xxx: SL12SP5 a12 driver compilation issue observed Changes: fallthrough macro is defined based on gcc version. - 10.02.07.00.a12-k1 BH 02/09/2022 - FCD-XXX: qla2xxx: Reset USCM stats/state and throttling on RSCN Changes: Reset USCM stats on getting an RSCN indicating a target port down. - FCD-XXX: qla2xxx: Increase max limit of ql2xnvme_queues Changes: Increase max limit of ql2xnvme_queues to (max_qpair-1) - FCD-478: qla2xxx: Fix missing devices on a LOGO from F-Port Changes: A call to logo all ports is made upon a F-Port LOGO. - FCD-XXX: qla2xxx: Move NVMe traffic to the slow queue on target congestion Changes: Steer the NVMe traffic to the slow Q on encountering target congestion - FCD-348: qla2xxx: edif: Fix slow session tear down. Changes: As a work around, driver would trigger a session tear down where it tell the local authentication application to also tear down. - FCD-XXX: qla2xxx: edif: Tweak debug log. Changes: Print AUTH ELS header to assist in debugging session's state of authentication app. - FCD-207: qla2xxx: Fix stuck session of prli reject Changes: Remove the stale code that cause the unintentional short cut. - FCD-1197: qla2xxx: Throttling up is seen when port is down Changes: Reset the stats/congestion state and the throttling algorithm on a link down event. - FCD-348: qla2xxx: Reduce false trigger to login Changes: Reduce the extra trigger to prevent multiple login to the same session. - FCD-207: qla2xxx: edif : Reduce N2N thrashing at app_start time Changes: make sure the old session is torn down before triggering a relogin. - FCD-207: qla2xxx: Fix laggy FC remote port session recovery Changes: allows the higher priority error recovery to run first before running the lower priority heart beat check. - FCD-XXX: qla2xxx: edif: Fix no logout on delete for n2n Changes: Set a flag to turn on implicit logout early in the session recovery to make sure it would go out in case of error. - FCD-348: qla2xxx: edif: fix session thrash 2 Changes: prevents prli from going out before authentication app gives the ok - FCD-348: qla2xxx: edif: tear down session if keys has been removed Changes: If all keys for a session has been deleted then trigger a session tear down. - FCD-348: qla2xxx: edif: fix no login after app start Changes: Add a re-login trigger to relogin. - FCD-207: qla2xxx: Fix hang due to session stuck Changes: Break the requeue cycle and exit. The session deletion code will trigger a session relogin. - FCD-348: qla2xxx: edif: reduce disruption due to multiple app start Changes: Driver will skip over session tear down if app start is seen more than once. - FCD-348: qla2xxx: edif: send logo for unexpected ike msg Changes: Terminate/cleanup the AUTH ELS exchange.Follow with a pass through LOGO. - FCD-348: qla2xxx: edif: Fix IO timeout due to over subscription Changes: Track IOCB resources to prevent over subscription of IOCB resources - FCD-207: qla2xxx: edif: fix n2n login retry for secure device Changes: Add a few more login retries to revive the connection. - FCD-1205: qla2xxx: Fix disk failure to rediscover Changes: Set the online state before reporting to UL of the availability of the session. - FCD-207: qla2xxx: Fix n2n inconsistent plogi Changes: Delete the session to restart the connection, where ELS pass through PLOGI would be used consistently. - FCD-1267: qla2xxx: Fix crash during module load unload test Changes: Driver correctly freeing a pre-allocated structure for purex packet handling - FCD-XXX: qla2xxx: Fix missed DMA unmap for NVME ls requests. Changes: Add an unmap call during ELS completion. - FCD-1266: qla2xxx: Fix loss of NVME namespaces after driver reload test Changes: Calling the localport registration under a mutex - FCD-1212: qla2xxx: Host does not retry RDF when retries are exhausted and there is an incoming RDF Changes: Reset the SCM ELS counters to zero once an RDF is received. - FCD-XXX: qla2xxx: Restrict CPU-qpair mapping to work for NVMe only - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. - FCD-XXX: qla2xxx: SCM: Add a bitmap for FPIN events. - 10.02.07.00.a11-k1 BH 01/17/2022 - FCD-738: Fix T10 DIF performance on high end setup Changes: Added high performing CRC-1 interface - FCD-1182: qla2xxx: Fix initrd build error on RHEL 9 Changes: Updated the build script specific to RHEL 9 - FCD-XXX: qla2xxx: Fix incorrect latency counter display Changes: Fix this by ignoring I/Os with unusually high latencies. - FCD-207: qla2xxx: Fix n2n discovery issue with secure target Changes: On app_start, driver will reset the login retry attempt count. - FCD-1180: qla2xxx: Use correct feature type field during rffid processing Changes: Driver sends RFF_ID for initiator type 28 i.e. NVMe insteads of SCSI two times - FCD-1159: qla2xxx: Host doesn't retry the RDF/EDC when jammed with idle/CRC Changes: Wake up the DPC thread from the timer context when EDC/RDF needs to be - FCD-XXXX: qla2xxx: Build module with "-mindirect-branch=thunk-extern" option on RHEL 9 - 10.02.07.00.a10-k1 BH 01/06/2022 - FCD-XXX: qla2xxx: Support for changes in kernel 5.6 and above(rhel9.0) Changes: Changes made specific to rhel9.0 - FCD-1136: qla2xxx: Throttling occurs even when USCM is disabled via CLI Changes: Update flags that control USCM features, correctly on ISP reset - FCD-1160: USCM continues to be active even if RDF response is jammed (and failed) Changes: USCM flags are updated properly when port toggle and RDF completion happen - 10.02.07.00.a9-k1 BH 01/03/2022 - FCD-1154: qla2xxx: Fix incorrect reporting of task management failure Changes: Corrected endianness. - 10.02.07.00.a8-k1 BH 12/23/2021 - FCD-814 : qla2xxx: Add a new v2 dport diagnostic feature. Changes: Buffer size is increased to 1024 bytes and handle START/RESTART command received from SDMAPI. - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. Changes: Ramp up to faster initially, to get closer to the sweet spot quicker. Be less prone to operating at lower bandwidth in case of a sudden workload spike. Operate more conservatively (prioritize self over the network). - FCD-XXX: qla2xxx: Do not track SCM stats for all ports in the zone Changes: Track SCM stats just for the host and the target - FCD-XXX: qla2xxx: Stats for FPIN with event type "Lost Credit" not incremented. Changes: Add incrementing of "Lost Credit" stats. - FCD-684: qla2xxx: Fix link down when connected to AG fabric with FAA enabled Changes: Remove setting PUN and VL support bits in init control block. - FCD-1004: qla2xxx: Debug message improvement when changing SCM profile. Changes: Use profile names when changing profiles - FCD-868: qla2xxx: lockdown: "Unsupported Firmware" message Changes: checked different BITs for checking lockdown feature. - FCD-682: qla2xxx: tcm_qla2xxx driver load fails with "Invalid argument" error Changes: As tcm_qla2xxx is untested/unused, make it a dummy driver and reduce unncessary noise created by this. - FCD-886: qla2xxx: Hard Lockup on Unload/Load task with serial log enabled Changes: Hard lockup is seen because serial console driver crashed because of excessive logging. It was finalized to document this as known issues. - FCD-XXX: qla2xxx: Apply USCM profile change immediately - 10.02.07.00.a7-k1 BH 11/05/2021 - FCD-926: qla2xxx: lockdown: lower debug severity messages - FCD-824: qla2xxx: lower debug severity message for fw lockdown Changes: This patch lower the severity of various log messages. - FCD-XXX: qla2xxx: Send LS_ACC for an incoming RDF Changes: Send the LS_ACC and the new RDF separately - FCD-721: qla2xxx: Set Max queue depth based on data direction. Changes: Max q depth for Initiator tracks Reads (per port) and Fcport tracks Writes (per fcport). - FCD-701: qla2xxx: Fix device reconnect in loop topology Changes: Fix by taking the main login path that acquires device handle. - FCD-XXX: qla2xxx: Add ql2xnvme_queues module parameter to configure number of NVME queues - 10.02.07.00.a6-k1 BH 10/08/2021 - FCD-786: Shown wrong FDMI data for 64G adaptor Changes: qla2xxx: Corrected transmission speed mask values for FC - FCD-717: add retry for exe fw Changes: qla2xxx: Driver will retry Exec FW command up to 4 retries - FCD-XXX: qla2xxx: Compile out map queue changes if present in nvme-fc - 10.02.07.00.a5-k1 BH 10/01/2021 - FCD-740: Fix scheduling while atomic Changes: qla2xxx: schedule the call to fc_remote_port_delete in non-interrupt context - FCD-691: Fix premature hw access after pci error Changes: qla2xxx: Check error condition still persist and/or wait until the OS to give the resume signal - FCD-756: Fix excessive messages during device logout Changes: qla2xxx: disable printing IO error messages by default - FCD-XXX: qla2xxx: abort fw dump if soft reset fail - FCD-XXX: qla2xxx: USCM: Retry USCM ELS for Logical busy error code - FCD-XXX: qla2xxx: USCM: USCM profile reset to Driver defaults - FCD-XXX: qla2xxx: Fix warning message due to adisc is being flush at /var/log/messages - 10.02.07.00.a4-k1 BH 09/20/2021 - FCD-721: Revert code that keeps track of queue-depth directionally. Reason: Observing issue while q-depth accounting - FCD-XXX: Cleanup stale code. Changes: qla2xxx: Remove unused experimental code that uses explicit PRLO as a way to tear down session. - FCD-XXX: edif: remove old doorbell interface Changes: qla2xxx:driver has implemented a new doorbell mechanism via bsg. - FCD-348: edif: add retry for els pass through Changes: qla2xxx: edif: Add additional retries to reduce higher level recovery. - FCD-XXX: edif: Synchronize NPIV deletion with authentication application Changes: qla2xxx: Notify authentication application of a NPIV deletion event is about to occur. - FCD-XXX: edif: Fix potential stuck session in sa update Changes: qla2xxx: Set flag properly for any attempt to relogin. - FCD-704: The external flag for tcm_qla2xxx was not set. qla2xxx: Add tcm_qla2xxx to externally supported module list. - 10.02.07.00.a3-k1 BH 09/08/2021 - FCD-XXX: qla2xxx: edif: wait for app to ack on sess down Changes: On session deletion, wait for app to acknowledge before moving on. - FCD-XXX: qla2xxx: edif: fix edif bsg Changes: Properly fill out the reply_payload_rcv_len field. - FCD-XXX: qla2xxx: edif: fix inconsistent check of db_flags Changes: Replace value check with bit flag check. - FCD-XXX: qla2xxx: edif: increase ELS payload Changes: Adjust memory buffer size to be able to handle max ELS payload. - FCD-343: qla2xxx: turn off target reset during issue_lip Changes: driver sends additional target reset to remote device before resetting the link. - FCD-XXX: qla2xxx: edif: Reduce Initiator-Initiator thrashing. Changes: Reduce unnecessary stress for authentication application to deal with unused connections. - FCD-XXX: qla2xxx: fix gnl list corruption Changes: move lock deletion behind lock. - FCD-XXX: qla2xxx: edif: flush stale events and msgs on session down Changes: Prevents authentication application from having to process stale data. - FCD-XXX: qla2xxx: edif: reduces thrashing of the connection. - FCD-XXX: qla2xxx: edif: tweak trace message - FCD-XXX: qla2xxx: edif: fix app start delay - FCD-XXX: qla2xxx: USCM: Handle SCM ELS from switch - FCD-XXX: qla2xxx: edif: fix app start fail - 10.02.07.00.a2-k1 BH 09/02/2021 - FCD-156: qla2xxx: 3PAR: Fix out of bound mem access Changes: Add additional check to make sure the range of memory - FCD-624: qla2xxx: Source driver gives compilation error on RHEL8.5 Changes: Offending code on tcm_qla2xxx module has been removed - FCD-xxx: qla2xxx: Fix use after free Changes: Would check for command is aborted / completed by FW before exiting the call. - ER148553: qla2xxx: relogin during fabric disturbance Changes : Set the scan_need flag to indicate a session - FCD-464: qla2xxx: Fix race between timeout handler and completion handler Changes: One reference is taken for the normal code path and one for the timeout path - FCD-453: Fix FC-NVME register localport failure. Changes: Module initialization is added to nvme_fc_port_template - FCD-XXX: qla2xxx: Process responses in Tx path if any available for better performance Changes: Call process_response_queue() in Tx path - FCD-492: Kernel crashes when accessing port_speed sysfs file Changes: CNA: Fix this by changing the lookup. - FCD-XXX: qla2xxx: Refactor asynchronous command initialization - FCD-XXX: qla2xxx: USCM - Add profile support for throttling IO - FCD-XXX: qla2xxx: Move heart beat handling from dpc thread to workqueue - FCD-XXX: USCM: Enhancement to throttle only read traffic during host congestion and write traffic during target congestion. - 10.02.07.00.a1-k1 BH 08/22/2021 - FCD-124: qla2xxx: edif: Use link event to wake up app Changes: The link up event would notify app of the present of a new SCSI Host. - FCD-299: qla2xxx: Fix crash in NVME abort path Changes: Fixed the issue by removing stale access. - FCD-XXX: qla2xxx: Display 16G only as supported speeds for 3830c card. Changes: This card doesn't support lower speeds, hence, update the fdmi and sysfs fields to display 16G only. - FCD-226: qla2xxx: Update details for building kdump initrd in NVMe BFS. Changes: Currently inbox driver doesn't support kdump/kexec kernel, hence user need to update kdump initrd to have OOB driver part of it. - FCD-372: qla2xxx: Anomaly in the congestion stats Changes: Clear the signal counter on a qaucli clear - FCD-279: Request QCC to check/report adapter's MCTP state Changes: qla2xxx: Add support for mailbox passthru - FCD-XXX: Perf improvement: Pick qpair such that Tx and Rx are processed on same CPU. Changes: qla2xxx: Select qpair depending on which CPU post_cmd() gets called - FCD-XXX: scsi: qla2xxx: Reserve extra IRQ vectors - 10.02.06.02-k1 BH 08/11/2021 - FCD-511: Path does not go into "Marginal" state on receiving FPIN-LI Change: qla2xxx: Pass the LI events to the scsi_transport_fc - 10.02.06.01-k1 BH 07/27/2021 - ERXXXXXX: qla2xxx: Check for firmware capability before creating QPair. Change: Move the check for FW attributes to right location. This check is specific for ISP25XX. - 10.02.06.00-k1 BH 07/21/2021 - ERXXXXXX: qla2xxx: Version number is changed from 10.02.06.00.a1-k1 to 10.02.06.00-k1 - 10.02.06.00.a1-k1 BH 06/29/2021 - FCD-297: Fix NVME session down detection Change: qla2xxx: Session tear down and allow relogin to re-drive the connection under condition - ER148553/FCD-156: Fix NVME retry Change: qla2xxx: Alternate back and forth on every PRLI failure until login retry count has depleted or it is succeeded. - FCD-316: System crash when number of CPUs forced to 2 - Change: qla2xxx: Sync queue idx with queue_pair_map idx. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - ERXXXXXX: qla2xxx: Readme: Remove workaround of forcing of INTa mode for kdump kernel. - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - FCD-316: System crash when number of CPUs forced to 2 Changes : qla2xxx: prevents unbalanced QP allocation where nr_hw_queues is two less than the number of CPUs. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - FCD-268: Multiple USCM ELS are sent - FCD-280: Fix issues reported by running a few Jammer tests Changes: qla2xxx: Retry the USCM ELS 3 times when there are failures. - FCD-172: build.sh: Fix udev script installation error - ER148402: Install restrictions when binary rpm is already installed. Changes: qla2xxx: Updated README file for documentation - ERXXXXXX: qla2xxx: Support kdump kernel for NVMe BFS. - ERXXXXXX: qla2xxx: Update README file for building kdump initrd in NVMe BFS. - ER148402: Disallow install if qla2xxx rpm is installed. Changes: qla2xxx: Prevent install from source if rpm is installed. - FCD-230: Add additional debug logs Changes: qla2xxx: Add additional logs to differentiate between FW driver and driver driven ELS -FCD-XXXX: Changes to support kdump kernel. Changes: qla2xxx: Don't allocate fw dump for kexec kernel and Allocate single Q for kexec kernel. - FCD-227: Linux Driver order of RDF to follow EDC ELS - FCD-225 - Qaucli fails to list scm stats for Qlipper - FCD-172: fix udev rule Changes: qla2xxx: permission of the rule file set to 644 - ER148529: NVMe initiator connected to brocade fabric are down Changes: qla2xxx: Fix hang on NVME command timeouts. - ER148531: SN1600Q/SN1610Q, Gen10PlusSnap4 - Async-login failed errors on BFS boot-up-QXCR1001796980 Changes: qla2xxx: Suppress unnecessary log messages during login - ER148578: Observed that initiator is sending prli type 0x8 for for nvme ports Changes: qla2xxx: fix NVME | FCP personality change. - ER148141: Driver vmkmgt: Don't differentiate Signals and FPIN's for the Congestion counters when they detected. Changes: qla2xxx: Split congestion warnings and alarms based on signals and FPINs - ERXXXXXX: Add support for marginal path. Changes: qla2xxx: Added support for eh_should_retry_cmd callback in qla2xxx host template. - ERXXXXXX: scsi: qla2xxx: Flush all sessions on zone disable - ERXXXXXX: scsi: qla2xxx: Fix memory size truncation - ERXXXXXX: scsi: qla2xxx: Fix a NULL pointer dereference in an error path - ERXXXXXX: qla2xxx: fix sparse warning. - ERXXXXXX: qla2xxx: edif: do secure plogi when auth app is present - ERXXXXXX: qla2xxx: Add license. - ERXXXXXX: qla2xxx: USCM - Do not send EDC/RDF ELS when firmware has already sent it - ERXXXXXX: qla2xxx: Inclusion words are applied on release note and readme file - ERXXXXXX: qla2xxx: edif: add N2N support for EDIF - ERXXXXXX: qla2xxx: Updated drelease.notes header - ERXXXXXX: qla2xxx: Fix hang during NVME session tear down. - ERXXXXXX: qla2xxx: USCM: Cleaned up a few debug messages - ERXXXXXX: qla2xxx: edif: fix edif enable flag - ER148546: USCM: QCC Cong Mgmt not available on port with FW:v9.07.00 and DVR:v10.02.05.00.a6-k Changes: qla2xxx: setting the flags to indicate to the application that the RDF is complete and SCM is supported. - ERXXXXXX: Add heartbeat check Changes: qla2xxx: Use 'no-op' mailbox command to check to see if FW is still responsive. - ERXXXXXX: DEBUG: simulate FW hang. Changes: qla2xxx: Driver will detect the hang and recover via hearbeat check. - ERXXXXXX: qla2xxx: Check for FW attributes before enabling MQ. - ERXXXXXX: qla2xxx: USCM Handle ELS errors from switch by retrying 3 times - ERXXXXXX: scsi: qla2xxx: Correct the supported speeds for 16G Mezz card. - ER148472: With NPIV ports, link bounce causes loss of strongSwan session at the target. Changes: qla2xxx: : fix npiv create errorneous error qla2xxx: EDIF: reject AUTH ELS on session down. qla2xxx: edif: Fix stale session - ER148478: System Crash while NPIV RAW IO ON VPORT LUNS on SLES15 SP3 + QLE 2692 + R7525 Changes: qla2xxx: fix unsafe removal from link list. - ERXXXXXX: qla2xxx: USCM - Send EDC and RDF ELS from the driver - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: v2: fix crash in PCIe error handling - ER148123: Issue with Max secure connection with override_lower_limits Changes: qla2xxx: v2: fix stuck session - ER148402: SLES, Driver Install location is inconsistent. Changes: qla2xxx: Fix driver install location for SLES - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Changes: qla2xxx: edif: doorbell tweak - ER148448: Issue w.r.t qaucli, where Remote type "Unknown" for eDIF env. for qaucli2.4.0.build 20 Changes: qla2xxx: fix port type info - ER148433: The log does not show a valid data rate while the link speed is 64G. Changes: qla2xxx: fix debug print of 64G link speed. - ER147650: 'show fdmi? command does not list ? OS Name and Version? parameter for SLES12SP4-QXCR1001771822 Changes: qla2xxx: Show OS name and version in FDMI-1 - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: fix mailbox recovery during PCIE error qla2xxx: v2: fix crash in PCIe error handling - ERXXXXXX: qla2xxx: Changes to support FCP2 Target. - ERXXXXXX: qla2xxx: include AER debug mask to default - ERXXXXXX: qla2xxx: fixes for compilation on RH8.4 - ERXXXXXX: qla2xxx: Do logout even if fabric scan retries got exhausted. - 10.02.05.00.a1-k1 BH 02/27/2021 - EDIF Changes: - ER148247: issue with nvme-npiv env, once we delete npivs, after a while, it is reducing strongswan connections. Change: free sa index during npiv delete - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Change: adjust online|offline notification to app and tweak LOGO on session down. - ERXXXXXX: qla2xxx: edif: tweak log message - ERXXXXXX: qla2xxx: edif: Redundant code (already set in qla_edb_node_alloc) - ER147707: qla2xxx: Device recovery not happening and OS hungs on qla2xxx Change: Fix RISC RESET completion polling. - ER148111: qla2xxx: FCPowerKit reflects huge delays in CMDlets execution. Change: Check lockdown functionality before requesting lockdown feature. - ER148277: USCM: Linux Peer showing misleading 'Congested, throttling down, permitted: 1', prior to 'Reached low watermark, permitted: 2': - Change: Fix misleading debug message - ERXXXXXX: adjust request/respond queue size for 28xx - ERXXXXXX: qla2xxx: Change %p to %px in the log messages. - 10.02.01.00.a15-k1 BH 11/12/2020 ERXXXXXX: qla2xxx: Updated README file for new module parameters - 10.02.01.00.a14-k1 BH 11/06/2020 - ER146725: eDIF another driver panic running script: ./test_target_no_unload.sh Change: qla2xxx: Fix crash in qla_nvme_abort_set_option. - ER147771: Call Trace while shutting down the adapter ports (LINK DOWN). Change: qla2xxx: Handle aborts correctly for port undergoing deletion. - ERXXXXXX: qla2xxx: Add scsi_change_queue_depth to slave configure. - 10.02.01.00.a13-k1 BH 10/28/2020 - ER147600: Cisco: rpd ELS cmd fail to fetch the speed capabilities Change: qla2xxx: Used correct rdp spec, which was broken during code clean-up. - ER147695: FC-NVMe target discovery fails when initator wwpn < target wwpn in an N2N (Direct Attach) config Change: qla2xxx: fix N2N + NVME connect retry fail - ER147832: Issue with uSCM Linux with QCC CLI for some configuration Change: qla2xxx: Show event severity only when device state is congested. - ER147824 : scmr_stat sysfs node runs out of memory Change: qla2xxx: Come up with a compact version of scmr_stat - ER147823: NVMe IO is not getting throttled up or down. Change: qla2xxx: Enable throttle control for NVMe targets for Peer Congestion. - ERXXXXXX: qla2xxx: Count tgt short term link if link comes back before dev_loss_tmo. - ERXXXXXX: qla2xxx: Correct the check for fcport while displaying target counters. - ERXXXXXX: qla2xxx: Change trigger for host short term link down to dev loss tmo. - ERXXXXXX: qla2xxx: Move an SCM log under a debug level. - ERXXXXXX: qla2xxx: Set vendor_rsp[0] value. - ERXXXXXX: qla2xxx: Make throttling messages more informative. - 10.02.01.00.a12-k1 SK 10/15/2020 - ER147625: NVMe IO's are failing with Read/Write after LIP reset. Change: qla2xxx:Return EBUSY until the remote port delete finishes. - ER147653: Target side strongswan start/stop, make initiator crashed. Change: qla2xxx: edif: v2 fix double bsg done. - ER147791: USCM: clear option is not clearing hba alarm/warning, or clear cong or nvme target stats. Change: qla2xxx: Clear Sev and NVMe Target Stats. - ER147793: USCM: Throttling has wrong throttling up info and event period is not honored. Change: qla2xxx: Fix Throttling algorithm regression. - ER147759: NVMe Admin commands are getting throttled and causing admin queue failures. Change: qla2xxx: Throttle NVMe I/O commands only. - ERXXXXXX: qla2xxx: edif: fix aes_gmac mode. - ERXXXXXX: qla2xxx: edif: v2: standardize on port_id_t for bsg api. - ERXXXXXX: qla2xxx: edif: fix 4byte align. - ERXXXXXX: qla2xxx: edif: fix ELS meta data. - ERXXXXXX: qla2xxx: Clear Congestion State/Throttling during chip Reset. - ERXXXXXX: qla2xxx: Clear SCM Severity as part of SCM Stats Clear. - 10.02.00.02.a11-k1 BH 10/09/2020 - ER147734 : Lip reset on the isolated port causes server crash Change: qla2xxx: Don't allow FW, MPI and lip reset on isolated port. - ER147479 - PPC BE RH7.6 - qla2xxx driver loading - machine crashed. Change: qla2xxx: Fixes for big endian machines - ER147646: Call Trace observed while validating a MPI Pause test scenario. Change: qla2xxx: Correct the WARN_ON check in qla_nvme_abort_set_option. - ER147615: Throttling does not work with low I/Os. Change: qla2xxx: Check and round off fractional I/Os to 1 on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: List NVMe targets under scmr_stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Don't check for port isolation during abort isp. - ERXXXXXX: qla2xxx: SCM: Turn off SCM port parameter update mailbox command. - ERXXXXXX: qla2xxx: Fix I/O failures during remote port toggle testing - 10.02.00.02.a10-k1 BH 09/25/2020 SCM Changes: - ERXXXXXX: Changes - qla2xxx: Clear Congestion state when an RSCN is received/target is torn down. qla2xxx: throttling algorithm improvement. qla2xxx: Add throttling support for NVMe targets. EDIF Changes: - ERXXXXX: LUN loss on ipsec stop/start on target side. Change: save Nport on receive of PLOGI - ERXXXXX: fix ELS receive collision between physical and NPIV hosts. Change: remove erroneous source Nport ID search. - ER147570: FCP Performance Drop in latest driver for smaller IOs size. Change: qla2xxx: Change WQ_UNBOUND to WQ_MEM_RECLAIM. WQ_MEM_RECLAIM : wq is guaranteed to have at least one execution context regardless of memory pressure. - ER147632: QLE2774: RHEL 8.2 System crashes while upgrading he FW from 9.6.0 to 9.6.1 with QCC CLI build 12 Change: qla2xxx: Fix system crash on nvme abort path by checking sp of aborting command before accessing it. - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. - ER147645: System panic while trying to capture debugfs stats for EED. Change: qla2xxx: Check rport before accessing target number. - ER147632: Fix potential stale mem access Change: remove stale sp pointer reference - CQXXXXXX: FPIN events are not readily decodable. Change: qla2xxx: Make FPIN events prints human readable. - ER146879: Add support to clear SCM Stats Change: qla2xxx: Added support to clear SCM/SCMR Stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Allow get host stat during reset and sync reset. - ERXXXXXX: qla2xxx: Set reset_cmd_err_cnt on reset failure only. - ERXXXXXX: qla2xxx: Add isolated flag and return EPERM on isolation. - ERXXXXXX: qla2xxx: Count short term link if link comes back in 10 sec. - ERXXXXXX: qla2xxx: Don't check for fw_started while posting nvme command. - ERXXXXXX: qla2xxx: Pass irq_offset to blk_mq_pci_map_queues API. - ERXXXXXX: qla2xxx: lockdown: fix stale sp access. - BZ1868688: qla2xxx: tear down session if FW say its down. - 10.02.00.02.a9-k1 BH 09/03/2020 - ER147554 - sg_reset appears hung iterating over too many Qpairs. Change - qla2xxx: limit interrupt vectors to number of cpu. - ERXXXXX - qla2xxx: klocwork: Fix Bit field 'mpi_-' has one bit and is signed. - ERXXXXX - qla2xxx: Change post del message from debug level to log level. - ERXXXXX - qla2xxx: lockdown: fixup - Change error response as per API test. - ERXXXXX - qla2xxx: Fix map_queue interface to use the correct blk-mq call. - ERXXXXX - Added Structural changes for SCM Phase 2 support. Change : qla2xxx: Update structure definitions for SCM to support backward compatibility. - 10.02.00.02.a8-k1 BH 08/30/2020 - ERXXXXXX - Fix point-to-point (N2N) device discovery issue. Change - qla2xxx: Fix point-to-point (N2N) device discovery issue. - ERXXXXXX - To wait for ABTS response on I/O timeouts for NVMe. Change - qla2xxx: To wait for ABTS response on I/O timeouts for NVMe. - ER147523 - BSG stack trace and SCM display issues. Change - SCM: Functional regression with a6 release. - ER 147413 - edif: Fix issue with DIF enable target discovery. Change - qla2xxx: edif: Fix issue with DIF enable target discovery. - ER147480 clear ASYNC_ACTIVE flag to allow relogin. Change - qla2xxx: fix stuck session. - ERXXXXXX - lockdown: add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support - 10.02.00.02.a7-k1 BH 08/22/2020 - ER147495 - edif changes Change - qla2xxx: edif: fix nvme discovery failure qla2xxx: edif: fix els corruption. - ER147478 - SLES 15sp1 10.02...a6-k compile warning Change - qla2xxx: Compilation changes for sles15sp1 - ERXXXXXX - add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support qla2xxx: lockdown: fix compile problem. do not submit - ERXXXXXX: SCMR changes Change - qla2xxx: SCMR: Correct scmr_outstanding_reqs accounting. qla2xxx: SCM: Changes to separate current_events and current_state. qla2xxx: SCMR: Increase local array size. - ER147298 : USCM "Congestion Warning" counter regression Change - qla2xxx: Correct FPIN Structure Definition (Severity). - 10.02.00.02.a6-k1 BH 08/13/2020 - ERXXXXXX - fix crash on session cleanup + unload. Change - qla2xxx: fix crash on session cleanup + unload. - ER147329 - edif changes Change - qla2xxx: edif: fix compile error. do not submit qla2xxx: edif: fix double free on ELS send failure. qla2xxx: edif: reject els if non secure device. qla2xxx: edif: reject ELS on session down. qla2xxx: edif: redefine purex dest addr to be more consistent. qla2xxx: edif: tweak debug messages. qla2xxx: edif: fix nvme+edif target connect problem. - ER147460 - issue with Diag test on QCC CLI 2.4.0 build 10 with 10.2.00.2-a5 driver Change - qla2xxx: edif: move bsg auth els into separate routine. qla2xxx: edif: Fix error in BSG ELS path that has valid response data. - ER147312 - Add support to report MPI FW state. Change - qla2xxx: Add support to report MPI FW state. qla2xxx: Fix reset of MPI firmware. qla2xxx: Fix MPI reset needed message. - ER147437 - With a5 driver observed warning messages. Change - qla2xxx: Compilation changes for Citrix, rhel and sles. - 10.02.00.02.a5-k1 BH 07/31/2020 - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. Change - qla2xxx: Don't process target debugfs stats if port is isolated. - ERXXXXXX : Add SCM stats to scmr_stats node. Change - qla2xxx: Add SCM stats to scmr_stats node. - ER147419 : Fix crash due to request q pointer extraction failure. Change - qla2xxx: Latency measurement patch. - ERXXXXXX : edif: remove redundant field in port_id_t Change -qla2xxx: edif: remove redundant field in port_id_t - ER147331 - extract bbc from PLOGI template payload. Change -qla2xxx: Fix buffer-buffer credit extraction error - ERXXXXXX : Split qla2x00_configure_local_loop() Change scsi: qla2xxx: Split qla2x00_configure_local_loop() - ERXXXXXX : SCMR - Add I/O flow control. Change - qla2xxx: SCMR - Add I/O flow control. - 10.02.00.02.a4-k1 BH 07/23/2020 - ER147402 - Do not install nvme auto connect script if OS is installing it. Change - qla2xxx: auto-connect scripts are install based on nvme-cli package. - ERXXXXXX - Fixed return status of nvme fcp request. Change - qla2xxx: Set NVME status code for failed NVME FCP request. - ERXXXXXX - Multi-que support for TMF. Change - qla2xxx: Multi-que support for TMF. - ERXXXXXX ? edif changes Change - qla2xxx: edif: simplify reserve/release of sa_index. qla2xxx: edif: tweak debug log. qla2xxx: edif: adjust ELS resp length. qla2xxx: edif: send logo on app stop. qla2xxx: edif: remove prlo in session deletion. qla2xxx: edif: Fix app stop stall. - ER147298 - USCM "Congestion Warning" counter regression w/.65 driver. Change - qla2xxx: Correct fpin_descriptor definition. qla2xxx: Consolidate EDIF & SCM Purex Calls. - ERXXXXXX - Calculate avg. time taken by different components for IO completion. Change - qla2xxx: Latency measurement patch. - 10.02.00.02.a3-k1 BH 07/16/2020 - ER147348 - Observing firmware dump while running qaucli -g post port isolation. Change - qla2xxx: Don't check firmware state in case of chip is down. - ER147338 - SLES: Driver load failed - modprobe: ERROR: module 'qla2xxx' is unsupported. Change - qla2xxx: Add support for loading external modules on SuSE. - ER147361 - System panic after enabling port isolated during TimeOutReset. Change - qla2xxx: Synchronize the update the host counters using lock. - ER147370 - Hardware Error counter not incrementing for MBX command timeout. Change - qla2xxx: Update hardware error count for various error conditions. - ERXXXXXX - The change is to help in debuggging. Change - qla2xxx: Move some messages from debug to normal log level. - ER147346 - Observed a call trace after port isolation. Change - qla2xxx: Fix the call trace for flush workqueue. - ERXXXXXX - For debug purpose. Change - qla2xxx: Add error counters to debugfs node. - 10.02.00.02.a2-k1 AE 07/10/2020 - ERXXXXXX - qla2xxx: Fix TCM compilation issues. Change - Enabled build of tcm_qla2xxx module and fixed compile issues. - ERXXXXXX - qla2xxx: edif : Added back the app_stop wait and avoid if link is down. Change - Added wait during app stop. - ERXXXXXX - qla2xxx: Set BIT_13 for NVMe Async events. Change - Driver changes to skip SLER for Async event command. - ER147323 - qla2xxx: Correct the check for sscanf return value. Change - Driver updated to check version correctly. - ERXXXXXX - qla2xxx: v2: Add EDIF support. Change - Refactoring EDIF code for modularity. - ER147298 - Congestion Warning/Alarm counters fail to increment Change - Update driver to increment the counters for congestion signals. - 10.02.00.02.a1-k1 AE 06/29/2020 - qla2xxx: Enable IOCB throttling by default. - qla2xxx: Implementation to get and manage host, target stats and initiator port. - qla2xxx: Add SLER and PI control support. - qla2xxx: Do not log message when reading port speed via sysfs - qla2xxx: fix null pointer access. - qla2xxx: Use MPI hang trigger to do PEGTUNE halt. - qla2xxx: Reduce erroneous error in link reset path - qla2xxx: v2: fix stalled N2N reconnect. - qla2xxx: Fix warnings on SLES12SP5. - qla2xxx: Fix compilation issues on SLES15 - qla2xxx: Compilation Fixes for SLES15SP1. - qla2xxx: Debugfs compilation issue fix for RH7.6. - qla2xxx: Fix gcc test compile error output being printed. - qla2xxx: Timestamp device online and offline transitions. - qla2xxx: Add rport fields in debugfs. - qla2xxx: Allow dev_loss_tmo setting for FC-NVMe devices. - qla2xxx: Setup debugfs entries for remote ports. - qla2xxx: Fix edif related compilation issue on RH7.6. - Fixes for compilation on hpe branch - qla2xxx: Compilation fixes for RH8.2 - qla2xxx: Compilation changes for RH7.6 - qla2xxx: Fixes for compilation on RH7.x I - qla2xxx: bsg_job to bsg_job_t - qla2xxx: I Unify source code to work with newer kernels. - qla2xxx: Makefile changes from code-uni-devel-10x. - qla2xxx: qla_edif file changes to compile the driver. - qla2xxx: Fix compilation issues. - qla2xxx: Fix Makefile issue. - qla2xxx: fix compile error - qla2xxx: Use explicit LOGO in target mode - qla2xxx: Add EDIF support. - qla2xxx: Addd edif related files. - qla2xxx: Fix MPI failure AEN (8200) handling. - qla2xxx: SCM - Backport optimizations and style changes from upstream work. - qla2xxx: Fix warning in qla_attr.c file. - qla2xxx: Fix nvme compilation error. - qla2xxx: Fix crash in alloc w/GFP_KERNEL + interrupt - Author : Quinn Tran <qutran@marvell.com> qla2xxx: v2: add iocb resource tracking. - qla2xxx: Fix WARN_ON in qla_nvme_register_hba. - qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime. - qla2xxx: Make tgt_port_database available in initiator mode. - qla2xxx: reduce noisy debug message. - qla2xxx: Fix mailbox Ch erroneous error - qla2xxx: fix login timeout. - qla2xxx: Accomodate for SCM FW attribute bit change. - qla2xxx: post FC event (FPIN) to transport FPIN handler. - qla2xxx: Hide fc_host_fpin_rcv kernel dependency. - qla2xxx: Add changes to compile across various kernels. - qla2xxx: Use active targets to update SCM stats. - qla2xxx: Move SCM functions to qla_isr to keep changes local. - qla2xxx: Code to process FLOGI ACC extended payload. - qedf: Fix compilation issue - revisit. - qla2xxx: SCM Phase 1 Implementation + 2 other patches. - qla2xxx: Enable PUREX passthru post ISP reset. - qla2xxx: Fix hang when issuing nvme disconnect-all in NPIV. - qla2xxx: performance tweak - scsi: qla2xxx: fix fcport null pointer access. - fixup! qla2xxx: Fix unbound NVME response length. - scsi: qla2xxx: Fix unbound NVME response length - qla2xxx: Add host attribute to trigger MPI hang. - qla2xxx: ONEOFF: silent dbg messages for good path io. - qla2xxx: ONEOFF: fix pDIF detection - qla2xxx: Snoop inquiry response atleast 168 bytes to determine proprietary DIF. - qla2xxx: ONEOFF: add debug counters for T10-PI/DIF - qla2xxx: ONEOFF: add MQ support for HP3PAR propritary T10-PI - qla2xxx: HPE 3PAR private T10-PI support. - qla2xxx: Check for fabric_priority flag during login - qla2xxx: use iocb_fabric_priority flag - qla2xxx: Fix QoS name and add debug logs - qla2xxx: Correction to tests for iocb fabric and fcport qos. - qla2xxx: Use ->isp_ops->read_optrom() in qla26xx_read_qos_fcport_table(). - qla2xxx: QoS fcport table index initialization improvement. - qla2xxx: Add QoS fcport table index to speed up search. - qla2xxx: Reduce stack on qos fcport priority routines. - qla2xxx: HPE: Register FDMI QOS - qla2xxx: Add bsg interface for qos lun level bitmask. - qla2xxx: Read E2E QoS fcport priority bitmasks from flash. - qla2xxx: Abstract qos lun level mask for iocb cs_ctl field. - qla2xxx: Add fabric priority qos lun iocb mechanism. - qla2xxx: Implement CT command GFO (Get Fabric Object). - qla2xxx: Add support for fabric priority per target. - qla2xxx: fix mtcp dump collection failure. - qla2xxx: Set Nport ID for N2N - qla2xxx: Fix crash during device discovery. - qla2xxx: Handle NVME status iocb correctly. - qla2xxx: Remove restriction of FC T10-PI and NVME - qla2xxx: serialize fc_port alloc in N2N - qla2xxx: NPIV does not come up after FW dump. - qla2xxx: fix RDP respond data format bug. - qla2xxx: force semaphore on flash validation failure. - qla2xxx: add more FW debug information - qla2xxx: Revert: Disable T10-DIF feature with FC-NVMe during probe - qla2xxx: Update BPM enablement semantics. - qla2xxx: fix FW resource print error. - qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs. - qla2xxx: Ensure flash updates return possible failure status through bsg interface. - qla2xxx: Improved secure flash support messages - qla2xxx: fix flag passing error - qla2xxx: Use FC generic update firmware options routine for ISP27xx. - qla2xxx: Avoid setting firmware options twice in 24xx_update_fw_options. - qla2xxX: Add 16.0GT for PCI String - qla2xxx: Use FW_STARTED macro - qla2xxx: Add fixes for mailbox command - qla2xxx: Fix login IOCB flag - qla2xxx: Save rscn_gen for new fcport - qla2xxx: firmware option 3 is clobbered by speed set - qla2xxx: ISP28xx active FW region - qla2xxx: Add portname to print logs in qla24xx_logio_entry(). - qla2xxx: Correction to MB in-direction selection in qla2x00_echo_test(). - qla2xxx: Correction to selection of loopback/echo test. - qla2xxx: Use endian macros to assign static fields in fwdump header. - qla2xxx: Add Speed in SFP print information - qla2xxx: Fix RDP response size - qla2xxx: Handle cases for limiting RDP response payload length. - qla2xxx: Add deferred queue for processing ABTS and RDP. - qla2xxx: Cleanup ELS/PUREX iocb fields. - qla2xxx: Add devid's and conditionals for 28xx. - qla2xxx: Add vendor extended FDMI additions and amendments. - qla2xxx: Provide separate RDP enable. - qla2xxx: Add vendor extended RDP additions and amendments. - qla2xxx: Add changes in preparation for vendor extended FDMI/RDP. - qla2xxx: Add 2061 PCI ID - qla2xxx: Remove all DIX-0 references - qla2xxx: Add endianizer macro calls to fc host stats. - qla2xxx: Add sysfs node for D-Port Diagnostics AEN data. - qla2xxx: Move free of fcport out of interrupt context. - qla2xxx: Add beacon LED config sysfs interface. - qla2xxx: Add sysfs hooks for FC-NVMe autoconnect - 10.01.00.22-k AE 06/29/2020 - Upstream driver as part of Linux 5.6 - 10.02.14.00-k1 AG 05/21/2025 - - 10.02.14.00.a4-k1 AG 02/27/2025 [FCD-4186] : Device discovery fails on continuous reboot (Hitachi) Resolution : In a fabric topo when there is mismatch in state of login between driver and FW, query FW again and proceed with login Scope : 27xx/28xx Adapters [FCD-XXX] : Make functions local to a file static Resolution : Make functions local to a file static Scope : 27xx, 28xx series Adapters [FCD-XXX] : Remove unused function Resolution : Function qla25xx_set_purex is unused - remove it Scope : All adapters [FCD-4729] : Compilation errors with Sles15sp6 Resolution : Fix compilation errors on Sles15 SP6 Scope : Series Adapters [FCD-4536] : Compilation errors on RHEL10 Resolution : RHEL 10 has rebased to the latest kernel resulting in several build issues. Fix them and ensure that it builds on older kernels as well. Scope : Series Adapters [FCD-4676] : Add support for RH 9.6 (compilation) Resolution : Fix compilation errors on RH 9.6 Scope : Series Adapters [FCD-XXX] : Update README to reflect the supported distros Resolution : Update README to reflect the supported distros Scope : All Adapters Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com> Change-Id: Ic4af035fd48a3137923c7d3590be4271b0a7fd32 commit e22ea0921e20bcf93db0fae2b8dd579005686908 Author: Anil Gurumurthy <agurumurthy@marvell.com> Date: Fri Jan 10 11:06:14 2025 +0530 qla2xxx: Update driver version to 10.02.13.03-k1. - 10.02.13.03-k1 AG 01/10/2025 [FCD-4627] : HPSD5.10-BFS RHEL9.5 system crash on Nimble-HF40 failover test. Resolution : Check for sp being valid, before freeing associated memory Scope : All - 10.02.13.02-k1 MR 01/07/2025 [FCD-4657] : Fix SCSI INQ issue for supporting T10 DIF. Resolution : Replace sp completion with qpair completion call.. Scope : 28XX - 10.02.13.01-k1 MR 01/02/2025 [FCD-1040] : Call scsi done and nvme done with good completion without lock. Resolution : Done changes to move scsi done and nvme done without lock. Scope : 27xx and above - 10.02.13.00-k1 AG 10/22/2024 - - 10.02.13.00.a3-k1 SD 10/09/2024 [FCD-XXX] : Crash seen during load/unload test in a loop Resolution : Delay module unload when there is a fabric scan going on Scope : All adapters [FCD-4193] : SCSI device never recovers after RSCN Resolution : Remove tape specific checks which prevented recovery Scope : All adapters - 10.02.12.01-k1 MR 05/29/2024 [FCD-3465] : Server got crashed while running port toggle test. Resolution : During vport_delete send async_logout explicitly. Scope : 28XX - 10.02.12.00-k1 SD 05/20/2024 - - 10.02.12.00.a5-k1 SD 05/07/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a4-k1 SD 04/25/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a3-k1 SD 03/15/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : SFP cache on legacy adapter Scope : all - 10.02.12.00.a2-k1 SK 02/08/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : Fix NVME + NPIV connect issue Resolution : Initialize irq offset Scope : ALL - 10.02.12.00.a1-k1 QT 01/09/2024 scsi: qla2xxx: Drop redundant pci_enable_pcie_error_reporting() Resolution : Fix RHEL 9.4 compile issue Scope : ALL [FCD-3515] : API support for SFP data cache Scope : 27xx, 28xx [FCD-xxx] : Fix SLES15.6 compile issue Resolution : Remove stale fields Scope : ALL [FCD-3634] : Remove check req_sg_cnt should be equal to rsp_sg_cnt. Resolution : Firmware supports multiple sg_cnt for request and response for CT commands, so remove the redundant check. Scope : All Adapters [FCD-717] : Move FCE Trace buffer allocation to user control Resolution : Modify existing DFS knob to allow user to enable|disable this feature. Scope : Any [FCD-xxx] : Remove del_work work from qla_schedule_sess_for_deletion. Resolution : Remove del_work work from qla_schedule_sess_for_deletion. Scope : All [FCD-xxx] : Additional target mode code cleanup. Resolution : Additional target mode code cleanup. Scope : All [FCD-xxx] : Update copyright information. Resolution : Update copyright information. Scope : All [FCD-xxx] : Remove target code from qla_target files. Resolution : Remove target code from qla_target files. Scope : All [FCD-xxx] : Remove target mode code from initiator specific files. Resolution : Remove target mode code from initiator specific files. Scope : All [FCD-xxx] : Move common code to initiator specific files. Resolution : Move common code to initiator specific files. Scope : All [FCD-3751] : Fix use after free on unload Resolution : Remove duplicate signals on freeing dpc_thread Scope : ALL [FCD-3515] : Caching SFP data Scope : 27xx, 28xx [FCD-xxx] : Exec FW with delay Resolution : Add delay before command retry Scope : 28xx [FCD-xxx] : fix abort in bsg timeout Resolution : Wait for bsg to return before abort exit Scope : ALL [FCD-xxx] : Use QP lock to search for bsg. Resolution : use correct lock to protect search Scope : ALL [FCD-xxx] : Remove SQ in queuecommand Resolution : Remove duplicate code. Scope : ALL [FCD-xxx] : Reduce fabric scan duplicate code. Resolution : Consolidate routines that handle GPNFT & GNNFT. Scope : ALL [FCP-743] : Remove ql2xstay_attach_on_load_failure Resolution : Remove driver parameter used as part of feature test. Scope : 27xx, 28xx - 10.02.11.00-k1 NJ 10/25/2023 [FCD-xxx] : Remove PCI ID 0x2971 Resolution : Remove PCI ID 0x2971 Scope : [FCD-3661] : Remove 8031 from deprecate and unmaintained list. Resolution : Remove 8031 from deprecate and unmaintained list. Scope : 8031 [FCD-3571] : Unable to resume FW dump collection Resolution : send notification to udev Scope : 27xx, 28xx [FCD-3631] : Convert Port disable state to maintenance mode Resolution : Rename state and turn flag indicator Scope : 27xx + 28xx - 10.02.11.00.a8-k1 NJ 10/13/2023 [FCD-3632] : Remove support for FCoE device ids. Resolution : Remove FCoE ids from pci table. Scope : 8xxx [FCD-3624] : Fix optrom version displayed in FDMI Resolution : Populate EFI version Scope : Series Adapters [FCD-3632] : Remove CNA reference from README. Resolution : Remove CNA reference from README. Scope : 8xxx - 10.02.11.00.a7-k1 NJ 09/22/2023 [FCD-3195] : Fix flash read failure Resolution : Check return code for each flash read. Scope : Series Adapters [FCD-3571] : System flood by fw dumps Resolution : udev script to pause fw dump collection Scope : Any [FCD-3566] : Limit FW dump improvement to 27xx + 28xx Resolution : Add filter for 27xx + 28xx adapters Scope : 27xx+ [FCD-3497] : Return ENOBUFS if sg_cnt is more than one for ELS cmds. Resolution : This error is because FW support single sg element for ELS Pass-through IOCB (0x53h). This particular error code will help API and Apps to display appropriate message to the user. Scope : All Adapters [FCD-3510] : RHEL & SLES OOB driver request: deprecate L8/Hilda HW Resolution : Added a frame work to display the message based on device and OS. Scope : L8 and L16 (Hilda and CNA) [FCD-3269] : Init Control Block is dereferenced incorrectly Resolution : Correctly dereference ICB Scope : 20xx [FCD-3421] : Add Support to collect fw_dump on system crash or panic. Resolution : Add Support to collect fw_dump on system crash or panic Scope : 27xx, 28xx - 10.02.11.00.a6-k1 MR 09/08/2023 [FCD-XXX] : Modify error code handling for sfp fw upgrade mbx. Resolution : Modify error code handling for sfp fw upgrade mbx. Scope : 28xx [FCD-XXX] : Block sysfs resets and fw_dump during sfp fw upgrade Resolution : Block sysfs resets and fw_dump during sfp fw upgrade Scope : 28xx [FCP-743] : Block sysfs access during maintenance mode Resolution : Add check for maintenance mode. Scope : Any [FCD-3506] : Fix double free of dsd_list during driver load. Resolution : add pointer check before access Scope : Any - 10.02.11.00.a5-k1 MR 08/18/2023 [RH BZ 2039422] : NVMe-FC kernel crash during reload driver test Resolution : validate nvme_local_port correctly Scope : Any [FCD-XXX] : Fix for potential Null pointer dereferenced Resolution : Check before dereferencing pointer Scope : Any [FCP-743] : Enable driver attach to bad HW Resolution : turn on ql2xstay_attach_on_load_failure option Scope : 27xx, 28xx - 10.02.11.00.a4-k1 MR 08/11/2023 [FCD-xxx] : Update README file for zio information Resolution : Update readme file with zio information Scope : Any [FCD-3415] : Std-DIF is not working with HPe K1 driver Resolution : Reset the protect bit in the INQ response only when pDIF is enabled and negotiated. Scope : 26xx/27xx/28xx - 10.02.11.00.a3-k1 AG 08/03/2023 [FCP-743] : Allow only selective BSG requests in maintenance mode Resolution : Allow certain BSG to go through during maintenance mode Scope : Any [FCP-743] : FW dump improvement Resolution : Improve data capture Scope : 27XX, 28XX [FCD-3252] : Unable to act on RSCN for port online. Resolution : Clear RSCN flag only when driver is acting on the notification Scope : Any [FCD-xxx] : 32 Bytes CDB Resolution : Use Type 6 IOCB for CDB bigger than 16Bytes Scope : Any Unit Test : i) force IO to use Type6 only for over the weekend run. ii) force error path(s) to make sure no crash. [FCD-xxx] : Move resource to allow code reuse. Resolution : relocate dsd_list to qpair Scope : Any - 10.02.11.00.a2-k1 AG 07/27/2023 [FCD-3411] : CS_DMA Error observed while running DIF IO Resolution : While running DIF enabled IO, a CS_DMA error was observed. A FW dump is needed to better debug this. So take a FW dump on encountering this. Scope : 27xx/288 series of adapters [FCD-3406] : Modifiy default zio threshold value. Resolution : Modifiy default zio threshold value. Scope : 27xx/28xx Series Adapters [FCD-3314] : Delay IO Abort on PCI error Resolution : On detection of PCI error, allow IO's to wind down. Scope : Any [FCD-3314] : Fix system crash due to bad pointer access Resolution : Check SRB type before access. Scope : 27xx+ - 10.02.11.00.a1-k1 AG 07/14/2023 - FCP-749: qla2xxx: Add support for build for RH 9.3 and RH 8.9 distro Resolution : Build on RH 9.3 was failing owing to change of definition of fc_host_fpin_rcv and removal of DID_TARGET_FAILURE. Fix part of it by updating to latest upstream code. Scope : 27xx/28xx series of adapters - FCD-3302 : During unload Error detected messages is seen. Resolution : Change the wording of the message as its not an error. Scope : Series Adapters - FCD-3293 : Initiator sever getting crashed after LOGO. Resolution : Fix double free of fcport Scope : Any - Revert "scsi: qla2xxx: Change default ZIO threshold." This reverts commit 8812bcc1b7a25494ec8755ff3b61412a9993ff5b. The ZIO threshold now is 64. - FCD-xxx : Fix unreachable code Resolution : Remove dead code Scope : 28xx+ - FCD-3232 : Potential risk of double free pointer detected in Coverity scan by ran by Citrix Resolution : NULL the pointer after first free. Scope : All - 10.02.10.00-k1 SK 06/14/2023 Non-alpha build - 10.02.10.00.a2-k1 BH 05/12/2023 - FCD-3140: qla2xxx: Fix command flush on cable pull. Changes: Add wait for commands to return. - FCD-XXX: qla2xxx: NVME|FCP prefer flag not being honored. Changes: Reread prefer flag on chip reset - FCD-XXX: qla2xxx: Update readme file - 10.02.10.00.a1-k1 BH 05/02/2023 - FCD-XXX: qla2xxx: Update Copyright Changes: Update Copyright for Marvell. - FCD-XXX: qla2xxx: Update manufacturer detail Changes: Update manufacturer detail to "Marvell" - FCD-3140: qla2xxx: Host crash during StressAndHostPortReset test Changes: Remove unused nvme_ls_waitq wait queue. - FCD-XXX: qla2xxx: [RH-BZ 2167274]: Wait for io return on terminate rport. Changes: dd wait to terminate_rport_io - 10.02.09.00.a11-k1 BH 03/27/2023 - FCD-XXX: qla2xxx: Add link down + logo rx stat counts Changes: Add counters to track link down and Logo receive. - 10.02.09.00.a10-k1 BH 03/17/2023 - FCD-XXX: qla2xxx: Support for update SFP firmware of ACCELINK Changes: [New Feature] Support for update SFP FW of ACCELINK WTD 64G - FCD-717: qla2xxx: Split FCE|EFT trace control Changes: Split buffer alloc and enable of feature into individual step. - BZ-2093878: qla2xxx: perform lockless command completion in abort path Changes: Perform lockless command completion in abort path - 10.02.09.00.a9-k1 BH 03/06/2023 - FCD-2390: qla2xxx: Fix N2N stuck connection. Changes: Clear the blocking flag. - FCD-2496: qla2xxx: Prevent command send on chip reset Changes: Check for chip reset before sending IOCB. - FCD-2035: qla2xxx: Fix mem access after free. Changes: Remove access of memory - FCD-2720: qla2xxx: Move cmd_to_req_q latency counter before processing response. - FCD-XXX: qla2xxx: Update readme file for current program - 10.02.09.00.a8-k1 BH 02/27/2023 - FCD-2585: qla2xxx: Remove unsupported ql2xenabledif option. Changes: Removed unsupported ql2xenabledif=1 option and validate the user input. - FCD-2305: qla2xxx: Error code did not return to upper layer Changes: Preserve error code from TMF and return it to upper layer. - FCD-2035: qla2xxx: fix inconsistent TMF timeout. Changes: Allow TMF error to return to upper layer without session tear down. - FCD-2035: qla2xxx: Fix TMF leak through. Changes: Check for chip reset or session change before sending Task management. - 10.02.09.00.a7-k1 BH 02/17/2023 - FCD-2858: qla2xxx: USCM: Check for vp_idx before setting EDC and RDF set flags. Changes: Add check for vp_idx before setting EDC and RDF set flags when processing RIDA. Revert patch: - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition. - 10.02.09.00.a6-k1 BH 02/13/2023 - FCD-2750: qla2xxx: IO's are failing on Standard DIF enabled 3PAR LUN Changes: Revert an offending patch and work on an issue with upstream. - 10.02.09.00.a5-k1 BH 02/06/2023 - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition Changes: Remove EDC and RDF set flags on Report ID Acquisition. - FCD-2879: qla2xxx: Compilation errors on SLES15SP5 Beta3-202301 Changes: Write generic code to find tag of scsi cmnd - FCD-2846: qla2xxx: Correct bsg_reply size in bsg interface Changes: Fix the bsg_job->reply_len with size of "struct fc_bsg_reply" - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the invariant expression in the condition - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the expression flogi_acc_pld_remaining == 0 - FCD-XXXX: qla2xxx: Changes of logs level for SFP temperature monitoring - 10.02.09.00.a4-k1 BH 01/29/2023 - FCD-2308: qla2xxx: Add bsg call to read port information Changes: Add bsg interface to allow app to read remote port information. - FCD-XXX: qla2xxx: KW-97439: unreachable code Changes: Return void if return value is not needed - FCD-XXX: qla2xxx: Add logs for SFP temperature monitoring Changes: Add debug log for Temperature Alert (8070h) Asynchronous Event - 10.02.09.00.a3-k1 BH 01/19/2023 - FCD-XXX: qla2xxx: Add support of RHEL9.2 - FCD-XXX: qla2xxx: Add support of RHEL8.8 - FCD-XXX: qla2xxx: Add support of SLES15 SP5 - FCD-2800: qla2xxx: Add support of OpenEuler-22.03 - 10.02.09.00.a2-k1 BH 01/10/2023 - FCD-XXX: qla2xxx: kw: unreachable code, SRB type is 0 just before latency counter incremented. Changes: SRB type is 0 just before latency counter incremented. - FCD-XXX: qla2xxx: kw: reset current_topology much later Changes: Reset current_topology much later on detecting - FCD-XXX: qla2xxx: kw: unreachable code, CS_COMPLETE is 0 and its already checked. Changes: Remove unreachable - FCD-XXX: qla2xxx: kw: Checking for port_state always yields zero Changes: Instead of bitwise AND check for port_state directly - FCD-1569: qla2xxx: Fix fw resource tracking Changes: Use global counter - FCD-XXX: qla2xxx: [ER-144639]: Flush mailbox commands on chip reset Changes: Use lock to prevent race condition. - FCD-2735: qla2xxx: USCM-VL: NVRAM VL disabled logins with extend FLOGI (VL enabled) Changes: Reset the spl. features control block flag to avoid logging in with ER_RDY. - FCD-XXX: qla2xxx: klockwork: Fix buffer over flow Changes: Use correct buffer size. - FCD-XXX: qla2xxx: EDIF: kw: remove unnecessary bit field - FCD-2563: qla2xxx: Turn off noisy message log. - FCD-XXX: qla2xxx: kw: remove dead code in qla24xx_config_rings - 10.02.09.00.a1-k1 BH 01/10/2023 - FCD-717: qla2xxx: allow FW dump extraction if load fail Changes: Add knob to force driver to stay attached to the fail adapter. - FCD-717: qla2xxx: Initialize FW buffer size with seed value Changes: Initialize FW Buffer size with seed value - FCD-XXX: qla2xxx: klockwork: Remove QLA_COMMAND_ERROR check in qla2x00_execute_fw. Changes: Remove the unnecessary QLA_COMMAND_ERROR check - FCD-2390: qla2xxx: Fix session hang in gnl Changes: Clear this flag to prevent blockage. - FCD-2390: qla2xxx: Fix erroneous link up failure Changes: Set fw_started flag early to prevent interrupts being dropped - FCD-2496: qla2xxx: Fix command flush during TMF Changes: Wait for commands flush before closing TMF - FCD-2035: qla2xxx: Limit TMF to 8 per function Changes: Limit TMF to 8 per function - FCD-XXX: qla2xxx: Add NVMe Disconnect support. Changes: Add support for NVMe Disconnect feature. - FCD-XXX: qla2xxx: Modify qla27xx_copy_fpin_pkt to support PURLS IOCB. Changes: Modified qla27xx_copy_fpin_pkt to support both PUREX and PURLS IOCBs. - FCD-717: qla2xxx: Adjust iocb resource on qpair create Changes: Add call to readjust iocb + exchange limit. - FCD-2390: qla2xxx: Fix deletion race condition Changes: Move check field behind lock - FCD-XXX: qla2xxx: klockwork: Pointer checked for NULL at linx x will be dereferenced at linx x+y. Changes: Remove the unnecessary Null check. The pointer will likely be valid. - FCD-XXX: qla2xxx: Observed call trace in smp_processor_id() with debug kernel Changes: Use raw_smp_processor_id API - FCD-2275: qla2xxx: USCM: Cleanup code related to IOPS based throttling Changes: IOPS and BW based throttling is not used. Remove those code. - FCD-2273: qla2xxx: USCM: Code cleanup w.r.t module params (ql2x_scmr_flow_ctl_tgt, ql2x_scmr_flow_ctl_host) Changes: Remove the redundant module parameters - FCD-2408: qla2xxx: USCM: Driver doesn't honor the adapter port Restore Default Settings Changes: Update the nvram values to the host as well as fcport - FCD-2363: qla2xxx: USCM: Slow Queue usage changes Changes: Use Slow queue only under specific scenarios - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Don't increment the counter for under-run. - FCD-2291: qla2xxx: Erroneous link down. Changes: Allow adapter reset to complete before discovery - FCD-2035: qla2xxx: Fix hang in task management Changes: Bail out of TMF on error - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path - FCD-XXX: qla2xxx: USCM: Debug log message improvement Changes: Log target WWPN for peer congestion - FCD-2164: qla2xxx: Fix stall session after app start Changes: Use session delete to avoid the accidental clearing of scan_flag - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Check fcport state before invoking the mailbox - FCD-XXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: Set throughput baseline on 1st FPIN - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix parsing the fpin when multiple descriptors are present - FCD-XXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCD-XXX: qla2xxx: USCM: Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: Fix for KW-97392 Changes :Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: Remove dead code - flagged by klocwork - FCD-847: qla2xxx: fixup: Fix exchange over subscription. - FCD-2434: qla2xxx: Fix crash when IO abort times out - FCD-XXX: qla2xxx: Rearrange scm rx path handling code. - 10.02.08.01-k1 BH 09/28/2022 - FCD-2392: Fix initrd image creation failure in OpenEuler, Kylin and UOS Changes: Add support for creating initrd image on openEuler, Kylin and UOS - 10.02.08.00-k1 BH 09/16/2022 - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Residual under-run is not an interface error, hence no need to increment that count. - FCD-2291: qla2xxx: Fix erroneous link down. Changes: Allow adapter reset to complete before any scan can start. - FCD-2035: qla2xxx: Fix hang in task management Changes: Add additional error check at various point - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced. - 10.02.08.00.a7-k1 BH 08/22/2022 - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path. - FCD-2164: qla2xxx: USCM: Fix stall session after app start Changes: Prevent accidental clearing of flag that blocks re-login - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset. - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Heck fcport state before invoking mailbox - FCDXXX: qla2xxx: USCM: Debug log message improvement - 10.02.08.00.a6-k1 BH 08/09/2022 - FCDXXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: if VL switchreduces the throughput below 50%, we would not throttle any further. - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix the FPIN parsing to take into account multiple descriptors. - FCDXXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCDXXX: qla2xxx: USCM:Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..10 - 10.02.08.00.a5-k1 BH 07/29/2022 - FCD-XXX: qla2xxx: klocwork: Possible Null Pointer Dereference Changes: Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: USCM: Fix mqueuecommand return code during throttle down request. - FCD-XXX: qla2xxx: Revert klockwork: Fix buffer overrun - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h - FCD-2035: qla2xxx: Fix Task Mgmt Cmd fail due to unavailable resource Changes: Limit TM commands to 8 per target. - 10.02.08.00.a4-k1 BH 07/23/2022 - FCD-847: qla2xxx: Fix exchange over subscription. Changes: check for exchange availability before command submission - FCD-XXX: qla2xxx: Remove unintended flag clearing Changes: Remove unintended flag clearing. - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h Changes: Add wait for completion of Marker! - FCD-XXX: Fix performance dip due to lock contention Changes: Save the allocated memory for reuse and avoid the lock - FCDXXX: qla2xxx: USCM: Do not send EDC and RDF for NPIV ports Changes: Disable sending USCM ELS for vports - FCDXXX: qla2xxx: USCM: VL: Do not set target speed to 1G for slow lane Changes: Do not set the target speed while changing lanes. - FCD-2012: qla2xxx: Throttling up messages seen when profile is changed Changes: Set the new profile for each fcport (along with the host). - FCD-XXX: qla2xxx: USCM: VL - Clean up FLOGI_ACC parsing Changes: structure that could be used to parse the FLOGI_ACC by using offsets - FCD-1990: qla2xxx: Fix nvram load config error Changes: Remove re-definition of port flags while enabling virtual lane support - FCD-XXX: qla2xxx: USCM:VL, I/O does not move back to the normal lane Changes: Check if I/O throttling is being done, before deciding to move the normal lane. - FCD-XXX: qla2xxx: Fix stall login Changes: Reset session state to allow relogin logic to re-drive the connection. - FCD-847: qla2xxx: Fix exchange over subscription for mgt cmd. Changes: would check for exchange availability before command submission. - FCD-847: qla2xxx: Fix exchange over subscription. Changes: would check for exchange availability before command submission. - FCD-XXX: qla2xxx: relocate/rename vp map. - FCD-XXX: qla2xxx: Klocwork: Fix for Unexpected type of a scan function parameter - 10.02.08.00.a3-k1 BH 07/01/2022 - FCD-1818: qla2xxx: Fix call trace in debug kernel due to missing spinlock init Changes: Fix the call trace by initializing trace lock. - FCD-1923: qla2xxx: USCM: VL - After disabling VL via CLI, status shows "Non-operational" Changes: Return VL status appropropriately - FCD-1922: qla2xxx: Fix discovery issues in FC-AL topology Changes: Checks FC loop map when Get ID list returns no device - FCD-1831: qla2xxx: Fix link failure in NIPV environment. Changes: Remove NPIV host from directly being able to chip reset. - FCD-XXX: qla2xxx: Fix DMA-API call trace on NVME LS requests with debug kernel Changes: Remove DMA mapping from the driver - FCD-XXX: qla2xxx: Fix KASAN use-after-free warning in qla24xx_sp_unmap Changes: Remove stale fcport access in qla2x00_rel_sp - FCD-XXX: qla2xxx: Fix KASAN out-of-bounds warning in qla_update_sp Changes: Size for memcpy was corrected to use the right length. - FCD-XXX: qla2xxx: Fix imbalance vha->vref_count Chnages: Add an extra ref count for the task management paths. - FCD-XXX: qla2xxx: Tweak Latency measurement Changes: Move the time read further ahead to the start of queuecommand and later to the point where it is just before scsi_done. - FCD-XXX: qla2xxx: klockwork: Silent superfluous warning. Changes: Remove superfluous Null check. - FCD-XXX: qla2xxx: klockwork: Fix buffer overrun Changes: Replace structure name to allow proper size calculation - FCD-XXX: qla2xxx: Remove dead code (GNN ID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code (GPNID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code. Changes: Removing drport field and FCPORT_UPDATE_NEEDED, and EDIF_TICK_NEEDED signals - FCD-XXX: qla2xxx: Do not select slow queue if USCM is enabled Changes: Do not select slow queue whilie initializing cpu map - FCD-XXX: Select HW queue depending on Tx CPU Changes: Select qpair which is in correlation with Tx CPU - FCD-XXX: qla2xxx: Add support for displaying I/O throttle information Changes: Display the driver I/O throttle information along with VL information - FCD-XXX: qla2xxx: USCM: Throttle only R/W commands for NVME Changes: Throttle only read/write IOs. - Bring back following reverted changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.08.00.a2-k1 BH 06/19/2022 - FCD-XXX: qla2xxx: klockwork - Check valid rport returned by fc_bsg_to_rport Changes: Check valid rport returned by fc_bsg_to_rport - FCD-XXX: qla2xxx: klockwork - Check for a valid fcport pointer Changes: Add a check for a valid fcport pointer at the time of exit - FCD-XXX: qla2xxx: klockwork - Move fcport NULL check to avoid dereference Changes: Move the fcport NULL check to avoid the dereference. - FCD-1883: qla2xxx: USCM: Adapter shows "RDF Complete" when Link is down Changes: Reset the flag, so that when USCM is negotiated, the CLI shows the correct status - FCD-1846: qla2xxx: USCM: A log message while clearing stats Changes: Add a log message while clearing USCM stats - FCD-XXX: qla2xxx: USCM: VL-Reset FC device virtual lane priority to normal on a port flap Changes: Reset the virtual lane to normal on a port flap, ISP reset - FCD-XXX: qla2xxx: USCM: VL-Set target congestion before switching lanes Changes: Set the target state before the lane switch. - FCD-1752: qla2xxx: USCM: VL-Sysfs does not show Virtual Lane as enabled Changes: extended flogi_acc can also be parsed correctly. - FCD-1652: qla2xxx: Check if port is online before sending ELS Changes: Check if port is online before sending ELS - FCD-XXX: scsi: qla2xxx: Synchronize rport dev_loss_tmo setting - 10.02.08.00.a1-k1 BH 05/27/2022 - FCD-XXX: qla2xxx: USCM: Virtual Lane, Fix PUN handling Changes: Have a default priority range for each lane and ensure that the range is programmed correctly - FCD-XXX: qla2xxx: USCM: Support for Virtual Lanes Changes: Enable Virtual Lane support for Cisco switch - 10.02.07.00-k1 BH 05/27/2022 - Non-alpha build - 10.02.07.00.a19-k1 BH 05/21/2022 - FCD-XXX : qla2xxx: USCM: Throttling is not honored for NVMe Changes: Enable NVMe READ/WRITE commands to be throttled - FCD-XXX: qla2xxx: USCM: Add counters to track directional throttling Changes: Add sysfs counters to have stats displayed for busy status returns. - FCD-1801: qla2xxx: USCM: CP reads go to zero while doing directional throttling Changes: Take into account the directional queue depth while returning a busy status to the stack. - FCD-1809: qla2xxx: USCM: Restoring USCM Profile to default result in driver - FCD-1798: qla2xxx: USCM: Profiles are not honored for peer congestion Chnages: Apply the profile to each target (fcport) when the profile is changed. Reverting the following changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.07.00.a18-k1 BH 05/12/2022 - FCD-1484: qla2xxx: Manufacturer details should be "Marvell Semiconductor, Inc." Changes: Update Manufacturer details to indicate Marvell Semiconductors - FCD-XXX: qla2xxx: USCM: Throttle only read and write commands Changes: Throttle only read and write commands. - FCD-XXX: qla2xxx: USCM: Do not clear throttle for Clear Cong FPIN. Changes: Do not clear throttle when Clear Congestion FPIN is received. - FCD-XXX: qla2xxx: USCM: Change default profile to Monitor Changes: Set the default throttle profile as Monitor. - FCD-XXX: qla2xxx: Fix few issues reported by klocwork tool - 10.02.07.00.a17-k1 BH 05/06/2022 - FCD-1522: qla2xxx: USCM: Throughput drops to zero in Monitor mode Changes: Restore qdepth based on monitor mode - FCD-1315: qla2xxx: Fix erroneous mailbox timeout after pci error inject. Changes: Clear wait for MB interrupt flag to prevent stale MB completion arriving - FCD-1424: Remove verbose IO debug messages Changes: Remove the IOCB debug messages for every IO - FCD-XXX: Support for NVMe parameters in Auxiliary Image Status Changes: Added new structure member, bit define and image status check. - 10.02.07.00.a16-k1 BH 04/08/2022 - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - FCD-1221: qla2xxx: USCM: Switch does not send FPINs after a EDC re-negotiation Changes: Send Link Service Request Information wih the EDC response, along with the other descriptors. - 10.02.07.00.a15-k1 BH 03/25/2022 - FCD-1249: qla2xxx: edif: Fix dropped IKE message. Changes: Fixes IKE message being dropped due to error in processing Purex IOCB and Continuation IOCBs. - FCD-1457: qla2xxx: Zero undefined mailbox IN registers Changes: Set zero to unuse register's value while requesting a new MB command. - FCD-1425: qla2xxx: USCM: Seconds since last event showing incorrect value Changes: Calculate delta time correctly - FCD-1287: qla2xxx: Fix incorrect display of max frame size. Changes: Save off the field of interest into separate location and convert into words. - FCD-XXX: qla2xxx: Fix memory leak when reading tgt_port_database debugfs file - FCD-XXX: qla2xxx: USCM: Do not reset SCM stats on a link bounce/ISP reset - 10.02.07.00.a14-k1 BH 03/14/2022 - FCD-XXX: qla2xxx: Fix losing FCP-2 targets on long port disable with IOs Changes: Fix this by accepting RSCN when the device is not online. - FCD-XXX: qla2xxx: Fix losing target when it reappears during delete Changes: Fix the issue by adding state checks before proceeding. - FCD-XXX: qla2xxx: Fix losing FCP-2 targets during port perturbation tests Changes: Fix was to ignore delete for FCP-2 devices in certain sequence. - FCD-119: qla2xxx: Fix crash due to stale srb access around IO timeouts Changes: Ensure srb is either returned during error IO timeout error escalation. If that is not possible fail the escalation path. - FCD-1132: qla2xxx: HPE3PAR: Fix IOCB resource count leak Changes: Decrement FW IOCB resource count. - FCD-1132: qla2xxx: Turn off MQ for 8G adapter. Changes: For 8G adapter, multi queue was enabled accidentally. - FCD-1385: Wind down adapter after pcie error. Changes: Detect the PCIE error and returns all IO's to upper layers. - FCD-1412: qla2xxx: Reset Congestion Warning/Alarm signals count. Changes: Reset signals at every signal check boundary (1 sec). - 10.02.07.00.a13-k1 BH 02/17/2022 - FCD-1353: qla2xx: a12/a11 driver compilation gives warning messages Changes: Fix the fall through warning - FCD-1342: qla2xxx: SL12SP5 a12 driver compilation issue observed Changes: fallthrough macro is defined based on gcc version. - 10.02.07.00.a12-k1 BH 02/09/2022 - FCD-XXX: qla2xxx: Reset USCM stats/state and throttling on RSCN Changes: Reset USCM stats on getting an RSCN indicating a target port down. - FCD-XXX: qla2xxx: Increase max limit of ql2xnvme_queues Changes: Increase max limit of ql2xnvme_queues to (max_qpair-1) - FCD-478: qla2xxx: Fix missing devices on a LOGO from F-Port Changes: A call to logo all ports is made upon a F-Port LOGO. - FCD-XXX: qla2xxx: Move NVMe traffic to the slow queue on target congestion Changes: Steer the NVMe traffic to the slow Q on encountering target congestion - FCD-348: qla2xxx: edif: Fix slow session tear down. Changes: As a work around, driver would trigger a session tear down where it tell the local authentication application to also tear down. - FCD-XXX: qla2xxx: edif: Tweak debug log. Changes: Print AUTH ELS header to assist in debugging session's state of authentication app. - FCD-207: qla2xxx: Fix stuck session of prli reject Changes: Remove the stale code that cause the unintentional short cut. - FCD-1197: qla2xxx: Throttling up is seen when port is down Changes: Reset the stats/congestion state and the throttling algorithm on a link down event. - FCD-348: qla2xxx: Reduce false trigger to login Changes: Reduce the extra trigger to prevent multiple login to the same session. - FCD-207: qla2xxx: edif : Reduce N2N thrashing at app_start time Changes: make sure the old session is torn down before triggering a relogin. - FCD-207: qla2xxx: Fix laggy FC remote port session recovery Changes: allows the higher priority error recovery to run first before running the lower priority heart beat check. - FCD-XXX: qla2xxx: edif: Fix no logout on delete for n2n Changes: Set a flag to turn on implicit logout early in the session recovery to make sure it would go out in case of error. - FCD-348: qla2xxx: edif: fix session thrash 2 Changes: prevents prli from going out before authentication app gives the ok - FCD-348: qla2xxx: edif: tear down session if keys has been removed Changes: If all keys for a session has been deleted then trigger a session tear down. - FCD-348: qla2xxx: edif: fix no login after app start Changes: Add a re-login trigger to relogin. - FCD-207: qla2xxx: Fix hang due to session stuck Changes: Break the requeue cycle and exit. The session deletion code will trigger a session relogin. - FCD-348: qla2xxx: edif: reduce disruption due to multiple app start Changes: Driver will skip over session tear down if app start is seen more than once. - FCD-348: qla2xxx: edif: send logo for unexpected ike msg Changes: Terminate/cleanup the AUTH ELS exchange.Follow with a pass through LOGO. - FCD-348: qla2xxx: edif: Fix IO timeout due to over subscription Changes: Track IOCB resources to prevent over subscription of IOCB resources - FCD-207: qla2xxx: edif: fix n2n login retry for secure device Changes: Add a few more login retries to revive the connection. - FCD-1205: qla2xxx: Fix disk failure to rediscover Changes: Set the online state before reporting to UL of the availability of the session. - FCD-207: qla2xxx: Fix n2n inconsistent plogi Changes: Delete the session to restart the connection, where ELS pass through PLOGI would be used consistently. - FCD-1267: qla2xxx: Fix crash during module load unload test Changes: Driver correctly freeing a pre-allocated structure for purex packet handling - FCD-XXX: qla2xxx: Fix missed DMA unmap for NVME ls requests. Changes: Add an unmap call during ELS completion. - FCD-1266: qla2xxx: Fix loss of NVME namespaces after driver reload test Changes: Calling the localport registration under a mutex - FCD-1212: qla2xxx: Host does not retry RDF when retries are exhausted and there is an incoming RDF Changes: Reset the SCM ELS counters to zero once an RDF is received. - FCD-XXX: qla2xxx: Restrict CPU-qpair mapping to work for NVMe only - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. - FCD-XXX: qla2xxx: SCM: Add a bitmap for FPIN events. - 10.02.07.00.a11-k1 BH 01/17/2022 - FCD-738: Fix T10 DIF performance on high end setup Changes: Added high performing CRC-1 interface - FCD-1182: qla2xxx: Fix initrd build error on RHEL 9 Changes: Updated the build script specific to RHEL 9 - FCD-XXX: qla2xxx: Fix incorrect latency counter display Changes: Fix this by ignoring I/Os with unusually high latencies. - FCD-207: qla2xxx: Fix n2n discovery issue with secure target Changes: On app_start, driver will reset the login retry attempt count. - FCD-1180: qla2xxx: Use correct feature type field during rffid processing Changes: Driver sends RFF_ID for initiator type 28 i.e. NVMe insteads of SCSI two times - FCD-1159: qla2xxx: Host doesn't retry the RDF/EDC when jammed with idle/CRC Changes: Wake up the DPC thread from the timer context when EDC/RDF needs to be - FCD-XXXX: qla2xxx: Build module with "-mindirect-branch=thunk-extern" option on RHEL 9 - 10.02.07.00.a10-k1 BH 01/06/2022 - FCD-XXX: qla2xxx: Support for changes in kernel 5.6 and above(rhel9.0) Changes: Changes made specific to rhel9.0 - FCD-1136: qla2xxx: Throttling occurs even when USCM is disabled via CLI Changes: Update flags that control USCM features, correctly on ISP reset - FCD-1160: USCM continues to be active even if RDF response is jammed (and failed) Changes: USCM flags are updated properly when port toggle and RDF completion happen - 10.02.07.00.a9-k1 BH 01/03/2022 - FCD-1154: qla2xxx: Fix incorrect reporting of task management failure Changes: Corrected endianness. - 10.02.07.00.a8-k1 BH 12/23/2021 - FCD-814 : qla2xxx: Add a new v2 dport diagnostic feature. Changes: Buffer size is increased to 1024 bytes and handle START/RESTART command received from SDMAPI. - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. Changes: Ramp up to faster initially, to get closer to the sweet spot quicker. Be less prone to operating at lower bandwidth in case of a sudden workload spike. Operate more conservatively (prioritize self over the network). - FCD-XXX: qla2xxx: Do not track SCM stats for all ports in the zone Changes: Track SCM stats just for the host and the target - FCD-XXX: qla2xxx: Stats for FPIN with event type "Lost Credit" not incremented. Changes: Add incrementing of "Lost Credit" stats. - FCD-684: qla2xxx: Fix link down when connected to AG fabric with FAA enabled Changes: Remove setting PUN and VL support bits in init control block. - FCD-1004: qla2xxx: Debug message improvement when changing SCM profile. Changes: Use profile names when changing profiles - FCD-868: qla2xxx: lockdown: "Unsupported Firmware" message Changes: checked different BITs for checking lockdown feature. - FCD-682: qla2xxx: tcm_qla2xxx driver load fails with "Invalid argument" error Changes: As tcm_qla2xxx is untested/unused, make it a dummy driver and reduce unncessary noise created by this. - FCD-886: qla2xxx: Hard Lockup on Unload/Load task with serial log enabled Changes: Hard lockup is seen because serial console driver crashed because of excessive logging. It was finalized to document this as known issues. - FCD-XXX: qla2xxx: Apply USCM profile change immediately - 10.02.07.00.a7-k1 BH 11/05/2021 - FCD-926: qla2xxx: lockdown: lower debug severity messages - FCD-824: qla2xxx: lower debug severity message for fw lockdown Changes: This patch lower the severity of various log messages. - FCD-XXX: qla2xxx: Send LS_ACC for an incoming RDF Changes: Send the LS_ACC and the new RDF separately - FCD-721: qla2xxx: Set Max queue depth based on data direction. Changes: Max q depth for Initiator tracks Reads (per port) and Fcport tracks Writes (per fcport). - FCD-701: qla2xxx: Fix device reconnect in loop topology Changes: Fix by taking the main login path that acquires device handle. - FCD-XXX: qla2xxx: Add ql2xnvme_queues module parameter to configure number of NVME queues - 10.02.07.00.a6-k1 BH 10/08/2021 - FCD-786: Shown wrong FDMI data for 64G adaptor Changes: qla2xxx: Corrected transmission speed mask values for FC - FCD-717: add retry for exe fw Changes: qla2xxx: Driver will retry Exec FW command up to 4 retries - FCD-XXX: qla2xxx: Compile out map queue changes if present in nvme-fc - 10.02.07.00.a5-k1 BH 10/01/2021 - FCD-740: Fix scheduling while atomic Changes: qla2xxx: schedule the call to fc_remote_port_delete in non-interrupt context - FCD-691: Fix premature hw access after pci error Changes: qla2xxx: Check error condition still persist and/or wait until the OS to give the resume signal - FCD-756: Fix excessive messages during device logout Changes: qla2xxx: disable printing IO error messages by default - FCD-XXX: qla2xxx: abort fw dump if soft reset fail - FCD-XXX: qla2xxx: USCM: Retry USCM ELS for Logical busy error code - FCD-XXX: qla2xxx: USCM: USCM profile reset to Driver defaults - FCD-XXX: qla2xxx: Fix warning message due to adisc is being flush at /var/log/messages - 10.02.07.00.a4-k1 BH 09/20/2021 - FCD-721: Revert code that keeps track of queue-depth directionally. Reason: Observing issue while q-depth accounting - FCD-XXX: Cleanup stale code. Changes: qla2xxx: Remove unused experimental code that uses explicit PRLO as a way to tear down session. - FCD-XXX: edif: remove old doorbell interface Changes: qla2xxx:driver has implemented a new doorbell mechanism via bsg. - FCD-348: edif: add retry for els pass through Changes: qla2xxx: edif: Add additional retries to reduce higher level recovery. - FCD-XXX: edif: Synchronize NPIV deletion with authentication application Changes: qla2xxx: Notify authentication application of a NPIV deletion event is about to occur. - FCD-XXX: edif: Fix potential stuck session in sa update Changes: qla2xxx: Set flag properly for any attempt to relogin. - FCD-704: The external flag for tcm_qla2xxx was not set. qla2xxx: Add tcm_qla2xxx to externally supported module list. - 10.02.07.00.a3-k1 BH 09/08/2021 - FCD-XXX: qla2xxx: edif: wait for app to ack on sess down Changes: On session deletion, wait for app to acknowledge before moving on. - FCD-XXX: qla2xxx: edif: fix edif bsg Changes: Properly fill out the reply_payload_rcv_len field. - FCD-XXX: qla2xxx: edif: fix inconsistent check of db_flags Changes: Replace value check with bit flag check. - FCD-XXX: qla2xxx: edif: increase ELS payload Changes: Adjust memory buffer size to be able to handle max ELS payload. - FCD-343: qla2xxx: turn off target reset during issue_lip Changes: driver sends additional target reset to remote device before resetting the link. - FCD-XXX: qla2xxx: edif: Reduce Initiator-Initiator thrashing. Changes: Reduce unnecessary stress for authentication application to deal with unused connections. - FCD-XXX: qla2xxx: fix gnl list corruption Changes: move lock deletion behind lock. - FCD-XXX: qla2xxx: edif: flush stale events and msgs on session down Changes: Prevents authentication application from having to process stale data. - FCD-XXX: qla2xxx: edif: reduces thrashing of the connection. - FCD-XXX: qla2xxx: edif: tweak trace message - FCD-XXX: qla2xxx: edif: fix app start delay - FCD-XXX: qla2xxx: USCM: Handle SCM ELS from switch - FCD-XXX: qla2xxx: edif: fix app start fail - 10.02.07.00.a2-k1 BH 09/02/2021 - FCD-156: qla2xxx: 3PAR: Fix out of bound mem access Changes: Add additional check to make sure the range of memory - FCD-624: qla2xxx: Source driver gives compilation error on RHEL8.5 Changes: Offending code on tcm_qla2xxx module has been removed - FCD-xxx: qla2xxx: Fix use after free Changes: Would check for command is aborted / completed by FW before exiting the call. - ER148553: qla2xxx: relogin during fabric disturbance Changes : Set the scan_need flag to indicate a session - FCD-464: qla2xxx: Fix race between timeout handler and completion handler Changes: One reference is taken for the normal code path and one for the timeout path - FCD-453: Fix FC-NVME register localport failure. Changes: Module initialization is added to nvme_fc_port_template - FCD-XXX: qla2xxx: Process responses in Tx path if any available for better performance Changes: Call process_response_queue() in Tx path - FCD-492: Kernel crashes when accessing port_speed sysfs file Changes: CNA: Fix this by changing the lookup. - FCD-XXX: qla2xxx: Refactor asynchronous command initialization - FCD-XXX: qla2xxx: USCM - Add profile support for throttling IO - FCD-XXX: qla2xxx: Move heart beat handling from dpc thread to workqueue - FCD-XXX: USCM: Enhancement to throttle only read traffic during host congestion and write traffic during target congestion. - 10.02.07.00.a1-k1 BH 08/22/2021 - FCD-124: qla2xxx: edif: Use link event to wake up app Changes: The link up event would notify app of the present of a new SCSI Host. - FCD-299: qla2xxx: Fix crash in NVME abort path Changes: Fixed the issue by removing stale access. - FCD-XXX: qla2xxx: Display 16G only as supported speeds for 3830c card. Changes: This card doesn't support lower speeds, hence, update the fdmi and sysfs fields to display 16G only. - FCD-226: qla2xxx: Update details for building kdump initrd in NVMe BFS. Changes: Currently inbox driver doesn't support kdump/kexec kernel, hence user need to update kdump initrd to have OOB driver part of it. - FCD-372: qla2xxx: Anomaly in the congestion stats Changes: Clear the signal counter on a qaucli clear - FCD-279: Request QCC to check/report adapter's MCTP state Changes: qla2xxx: Add support for mailbox passthru - FCD-XXX: Perf improvement: Pick qpair such that Tx and Rx are processed on same CPU. Changes: qla2xxx: Select qpair depending on which CPU post_cmd() gets called - FCD-XXX: scsi: qla2xxx: Reserve extra IRQ vectors - 10.02.06.02-k1 BH 08/11/2021 - FCD-511: Path does not go into "Marginal" state on receiving FPIN-LI Change: qla2xxx: Pass the LI events to the scsi_transport_fc - 10.02.06.01-k1 BH 07/27/2021 - ERXXXXXX: qla2xxx: Check for firmware capability before creating QPair. Change: Move the check for FW attributes to right location. This check is specific for ISP25XX. - 10.02.06.00-k1 BH 07/21/2021 - ERXXXXXX: qla2xxx: Version number is changed from 10.02.06.00.a1-k1 to 10.02.06.00-k1 - 10.02.06.00.a1-k1 BH 06/29/2021 - FCD-297: Fix NVME session down detection Change: qla2xxx: Session tear down and allow relogin to re-drive the connection under condition - ER148553/FCD-156: Fix NVME retry Change: qla2xxx: Alternate back and forth on every PRLI failure until login retry count has depleted or it is succeeded. - FCD-316: System crash when number of CPUs forced to 2 - Change: qla2xxx: Sync queue idx with queue_pair_map idx. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - ERXXXXXX: qla2xxx: Readme: Remove workaround of forcing of INTa mode for kdump kernel. - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - FCD-316: System crash when number of CPUs forced to 2 Changes : qla2xxx: prevents unbalanced QP allocation where nr_hw_queues is two less than the number of CPUs. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - FCD-268: Multiple USCM ELS are sent - FCD-280: Fix issues reported by running a few Jammer tests Changes: qla2xxx: Retry the USCM ELS 3 times when there are failures. - FCD-172: build.sh: Fix udev script installation error - ER148402: Install restrictions when binary rpm is already installed. Changes: qla2xxx: Updated README file for documentation - ERXXXXXX: qla2xxx: Support kdump kernel for NVMe BFS. - ERXXXXXX: qla2xxx: Update README file for building kdump initrd in NVMe BFS. - ER148402: Disallow install if qla2xxx rpm is installed. Changes: qla2xxx: Prevent install from source if rpm is installed. - FCD-230: Add additional debug logs Changes: qla2xxx: Add additional logs to differentiate between FW driver and driver driven ELS -FCD-XXXX: Changes to support kdump kernel. Changes: qla2xxx: Don't allocate fw dump for kexec kernel and Allocate single Q for kexec kernel. - FCD-227: Linux Driver order of RDF to follow EDC ELS - FCD-225 - Qaucli fails to list scm stats for Qlipper - FCD-172: fix udev rule Changes: qla2xxx: permission of the rule file set to 644 - ER148529: NVMe initiator connected to brocade fabric are down Changes: qla2xxx: Fix hang on NVME command timeouts. - ER148531: SN1600Q/SN1610Q, Gen10PlusSnap4 - Async-login failed errors on BFS boot-up-QXCR1001796980 Changes: qla2xxx: Suppress unnecessary log messages during login - ER148578: Observed that initiator is sending prli type 0x8 for for nvme ports Changes: qla2xxx: fix NVME | FCP personality change. - ER148141: Driver vmkmgt: Don't differentiate Signals and FPIN's for the Congestion counters when they detected. Changes: qla2xxx: Split congestion warnings and alarms based on signals and FPINs - ERXXXXXX: Add support for marginal path. Changes: qla2xxx: Added support for eh_should_retry_cmd callback in qla2xxx host template. - ERXXXXXX: scsi: qla2xxx: Flush all sessions on zone disable - ERXXXXXX: scsi: qla2xxx: Fix memory size truncation - ERXXXXXX: scsi: qla2xxx: Fix a NULL pointer dereference in an error path - ERXXXXXX: qla2xxx: fix sparse warning. - ERXXXXXX: qla2xxx: edif: do secure plogi when auth app is present - ERXXXXXX: qla2xxx: Add license. - ERXXXXXX: qla2xxx: USCM - Do not send EDC/RDF ELS when firmware has already sent it - ERXXXXXX: qla2xxx: Inclusion words are applied on release note and readme file - ERXXXXXX: qla2xxx: edif: add N2N support for EDIF - ERXXXXXX: qla2xxx: Updated drelease.notes header - ERXXXXXX: qla2xxx: Fix hang during NVME session tear down. - ERXXXXXX: qla2xxx: USCM: Cleaned up a few debug messages - ERXXXXXX: qla2xxx: edif: fix edif enable flag - ER148546: USCM: QCC Cong Mgmt not available on port with FW:v9.07.00 and DVR:v10.02.05.00.a6-k Changes: qla2xxx: setting the flags to indicate to the application that the RDF is complete and SCM is supported. - ERXXXXXX: Add heartbeat check Changes: qla2xxx: Use 'no-op' mailbox command to check to see if FW is still responsive. - ERXXXXXX: DEBUG: simulate FW hang. Changes: qla2xxx: Driver will detect the hang and recover via hearbeat check. - ERXXXXXX: qla2xxx: Check for FW attributes before enabling MQ. - ERXXXXXX: qla2xxx: USCM Handle ELS errors from switch by retrying 3 times - ERXXXXXX: scsi: qla2xxx: Correct the supported speeds for 16G Mezz card. - ER148472: With NPIV ports, link bounce causes loss of strongSwan session at the target. Changes: qla2xxx: : fix npiv create errorneous error qla2xxx: EDIF: reject AUTH ELS on session down. qla2xxx: edif: Fix stale session - ER148478: System Crash while NPIV RAW IO ON VPORT LUNS on SLES15 SP3 + QLE 2692 + R7525 Changes: qla2xxx: fix unsafe removal from link list. - ERXXXXXX: qla2xxx: USCM - Send EDC and RDF ELS from the driver - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: v2: fix crash in PCIe error handling - ER148123: Issue with Max secure connection with override_lower_limits Changes: qla2xxx: v2: fix stuck session - ER148402: SLES, Driver Install location is inconsistent. Changes: qla2xxx: Fix driver install location for SLES - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Changes: qla2xxx: edif: doorbell tweak - ER148448: Issue w.r.t qaucli, where Remote type "Unknown" for eDIF env. for qaucli2.4.0.build 20 Changes: qla2xxx: fix port type info - ER148433: The log does not show a valid data rate while the link speed is 64G. Changes: qla2xxx: fix debug print of 64G link speed. - ER147650: 'show fdmi? command does not list ? OS Name and Version? parameter for SLES12SP4-QXCR1001771822 Changes: qla2xxx: Show OS name and version in FDMI-1 - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: fix mailbox recovery during PCIE error qla2xxx: v2: fix crash in PCIe error handling - ERXXXXXX: qla2xxx: Changes to support FCP2 Target. - ERXXXXXX: qla2xxx: include AER debug mask to default - ERXXXXXX: qla2xxx: fixes for compilation on RH8.4 - ERXXXXXX: qla2xxx: Do logout even if fabric scan retries got exhausted. - 10.02.05.00.a1-k1 BH 02/27/2021 - EDIF Changes: - ER148247: issue with nvme-npiv env, once we delete npivs, after a while, it is reducing strongswan connections. Change: free sa index during npiv delete - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Change: adjust online|offline notification to app and tweak LOGO on session down. - ERXXXXXX: qla2xxx: edif: tweak log message - ERXXXXXX: qla2xxx: edif: Redundant code (already set in qla_edb_node_alloc) - ER147707: qla2xxx: Device recovery not happening and OS hungs on qla2xxx Change: Fix RISC RESET completion polling. - ER148111: qla2xxx: FCPowerKit reflects huge delays in CMDlets execution. Change: Check lockdown functionality before requesting lockdown feature. - ER148277: USCM: Linux Peer showing misleading 'Congested, throttling down, permitted: 1', prior to 'Reached low watermark, permitted: 2': - Change: Fix misleading debug message - ERXXXXXX: adjust request/respond queue size for 28xx - ERXXXXXX: qla2xxx: Change %p to %px in the log messages. - 10.02.01.00.a15-k1 BH 11/12/2020 ERXXXXXX: qla2xxx: Updated README file for new module parameters - 10.02.01.00.a14-k1 BH 11/06/2020 - ER146725: eDIF another driver panic running script: ./test_target_no_unload.sh Change: qla2xxx: Fix crash in qla_nvme_abort_set_option. - ER147771: Call Trace while shutting down the adapter ports (LINK DOWN). Change: qla2xxx: Handle aborts correctly for port undergoing deletion. - ERXXXXXX: qla2xxx: Add scsi_change_queue_depth to slave configure. - 10.02.01.00.a13-k1 BH 10/28/2020 - ER147600: Cisco: rpd ELS cmd fail to fetch the speed capabilities Change: qla2xxx: Used correct rdp spec, which was broken during code clean-up. - ER147695: FC-NVMe target discovery fails when initator wwpn < target wwpn in an N2N (Direct Attach) config Change: qla2xxx: fix N2N + NVME connect retry fail - ER147832: Issue with uSCM Linux with QCC CLI for some configuration Change: qla2xxx: Show event severity only when device state is congested. - ER147824 : scmr_stat sysfs node runs out of memory Change: qla2xxx: Come up with a compact version of scmr_stat - ER147823: NVMe IO is not getting throttled up or down. Change: qla2xxx: Enable throttle control for NVMe targets for Peer Congestion. - ERXXXXXX: qla2xxx: Count tgt short term link if link comes back before dev_loss_tmo. - ERXXXXXX: qla2xxx: Correct the check for fcport while displaying target counters. - ERXXXXXX: qla2xxx: Change trigger for host short term link down to dev loss tmo. - ERXXXXXX: qla2xxx: Move an SCM log under a debug level. - ERXXXXXX: qla2xxx: Set vendor_rsp[0] value. - ERXXXXXX: qla2xxx: Make throttling messages more informative. - 10.02.01.00.a12-k1 SK 10/15/2020 - ER147625: NVMe IO's are failing with Read/Write after LIP reset. Change: qla2xxx:Return EBUSY until the remote port delete finishes. - ER147653: Target side strongswan start/stop, make initiator crashed. Change: qla2xxx: edif: v2 fix double bsg done. - ER147791: USCM: clear option is not clearing hba alarm/warning, or clear cong or nvme target stats. Change: qla2xxx: Clear Sev and NVMe Target Stats. - ER147793: USCM: Throttling has wrong throttling up info and event period is not honored. Change: qla2xxx: Fix Throttling algorithm regression. - ER147759: NVMe Admin commands are getting throttled and causing admin queue failures. Change: qla2xxx: Throttle NVMe I/O commands only. - ERXXXXXX: qla2xxx: edif: fix aes_gmac mode. - ERXXXXXX: qla2xxx: edif: v2: standardize on port_id_t for bsg api. - ERXXXXXX: qla2xxx: edif: fix 4byte align. - ERXXXXXX: qla2xxx: edif: fix ELS meta data. - ERXXXXXX: qla2xxx: Clear Congestion State/Throttling during chip Reset. - ERXXXXXX: qla2xxx: Clear SCM Severity as part of SCM Stats Clear. - 10.02.00.02.a11-k1 BH 10/09/2020 - ER147734 : Lip reset on the isolated port causes server crash Change: qla2xxx: Don't allow FW, MPI and lip reset on isolated port. - ER147479 - PPC BE RH7.6 - qla2xxx driver loading - machine crashed. Change: qla2xxx: Fixes for big endian machines - ER147646: Call Trace observed while validating a MPI Pause test scenario. Change: qla2xxx: Correct the WARN_ON check in qla_nvme_abort_set_option. - ER147615: Throttling does not work with low I/Os. Change: qla2xxx: Check and round off fractional I/Os to 1 on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: List NVMe targets under scmr_stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Don't check for port isolation during abort isp. - ERXXXXXX: qla2xxx: SCM: Turn off SCM port parameter update mailbox command. - ERXXXXXX: qla2xxx: Fix I/O failures during remote port toggle testing - 10.02.00.02.a10-k1 BH 09/25/2020 SCM Changes: - ERXXXXXX: Changes - qla2xxx: Clear Congestion state when an RSCN is received/target is torn down. qla2xxx: throttling algorithm improvement. qla2xxx: Add throttling support for NVMe targets. EDIF Changes: - ERXXXXX: LUN loss on ipsec stop/start on target side. Change: save Nport on receive of PLOGI - ERXXXXX: fix ELS receive collision between physical and NPIV hosts. Change: remove erroneous source Nport ID search. - ER147570: FCP Performance Drop in latest driver for smaller IOs size. Change: qla2xxx: Change WQ_UNBOUND to WQ_MEM_RECLAIM. WQ_MEM_RECLAIM : wq is guaranteed to have at least one execution context regardless of memory pressure. - ER147632: QLE2774: RHEL 8.2 System crashes while upgrading he FW from 9.6.0 to 9.6.1 with QCC CLI build 12 Change: qla2xxx: Fix system crash on nvme abort path by checking sp of aborting command before accessing it. - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. - ER147645: System panic while trying to capture debugfs stats for EED. Change: qla2xxx: Check rport before accessing target number. - ER147632: Fix potential stale mem access Change: remove stale sp pointer reference - CQXXXXXX: FPIN events are not readily decodable. Change: qla2xxx: Make FPIN events prints human readable. - ER146879: Add support to clear SCM Stats Change: qla2xxx: Added support to clear SCM/SCMR Stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Allow get host stat during reset and sync reset. - ERXXXXXX: qla2xxx: Set reset_cmd_err_cnt on reset failure only. - ERXXXXXX: qla2xxx: Add isolated flag and return EPERM on isolation. - ERXXXXXX: qla2xxx: Count short term link if link comes back in 10 sec. - ERXXXXXX: qla2xxx: Don't check for fw_started while posting nvme command. - ERXXXXXX: qla2xxx: Pass irq_offset to blk_mq_pci_map_queues API. - ERXXXXXX: qla2xxx: lockdown: fix stale sp access. - BZ1868688: qla2xxx: tear down session if FW say its down. - 10.02.00.02.a9-k1 BH 09/03/2020 - ER147554 - sg_reset appears hung iterating over too many Qpairs. Change - qla2xxx: limit interrupt vectors to number of cpu. - ERXXXXX - qla2xxx: klocwork: Fix Bit field 'mpi_-' has one bit and is signed. - ERXXXXX - qla2xxx: Change post del message from debug level to log level. - ERXXXXX - qla2xxx: lockdown: fixup - Change error response as per API test. - ERXXXXX - qla2xxx: Fix map_queue interface to use the correct blk-mq call. - ERXXXXX - Added Structural changes for SCM Phase 2 support. Change : qla2xxx: Update structure definitions for SCM to support backward compatibility. - 10.02.00.02.a8-k1 BH 08/30/2020 - ERXXXXXX - Fix point-to-point (N2N) device discovery issue. Change - qla2xxx: Fix point-to-point (N2N) device discovery issue. - ERXXXXXX - To wait for ABTS response on I/O timeouts for NVMe. Change - qla2xxx: To wait for ABTS response on I/O timeouts for NVMe. - ER147523 - BSG stack trace and SCM display issues. Change - SCM: Functional regression with a6 release. - ER 147413 - edif: Fix issue with DIF enable target discovery. Change - qla2xxx: edif: Fix issue with DIF enable target discovery. - ER147480 clear ASYNC_ACTIVE flag to allow relogin. Change - qla2xxx: fix stuck session. - ERXXXXXX - lockdown: add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support - 10.02.00.02.a7-k1 BH 08/22/2020 - ER147495 - edif changes Change - qla2xxx: edif: fix nvme discovery failure qla2xxx: edif: fix els corruption. - ER147478 - SLES 15sp1 10.02...a6-k compile warning Change - qla2xxx: Compilation changes for sles15sp1 - ERXXXXXX - add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support qla2xxx: lockdown: fix compile problem. do not submit - ERXXXXXX: SCMR changes Change - qla2xxx: SCMR: Correct scmr_outstanding_reqs accounting. qla2xxx: SCM: Changes to separate current_events and current_state. qla2xxx: SCMR: Increase local array size. - ER147298 : USCM "Congestion Warning" counter regression Change - qla2xxx: Correct FPIN Structure Definition (Severity). - 10.02.00.02.a6-k1 BH 08/13/2020 - ERXXXXXX - fix crash on session cleanup + unload. Change - qla2xxx: fix crash on session cleanup + unload. - ER147329 - edif changes Change - qla2xxx: edif: fix compile error. do not submit qla2xxx: edif: fix double free on ELS send failure. qla2xxx: edif: reject els if non secure device. qla2xxx: edif: reject ELS on session down. qla2xxx: edif: redefine purex dest addr to be more consistent. qla2xxx: edif: tweak debug messages. qla2xxx: edif: fix nvme+edif target connect problem. - ER147460 - issue with Diag test on QCC CLI 2.4.0 build 10 with 10.2.00.2-a5 driver Change - qla2xxx: edif: move bsg auth els into separate routine. qla2xxx: edif: Fix error in BSG ELS path that has valid response data. - ER147312 - Add support to report MPI FW state. Change - qla2xxx: Add support to report MPI FW state. qla2xxx: Fix reset of MPI firmware. qla2xxx: Fix MPI reset needed message. - ER147437 - With a5 driver observed warning messages. Change - qla2xxx: Compilation changes for Citrix, rhel and sles. - 10.02.00.02.a5-k1 BH 07/31/2020 - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. Change - qla2xxx: Don't process target debugfs stats if port is isolated. - ERXXXXXX : Add SCM stats to scmr_stats node. Change - qla2xxx: Add SCM stats to scmr_stats node. - ER147419 : Fix crash due to request q pointer extraction failure. Change - qla2xxx: Latency measurement patch. - ERXXXXXX : edif: remove redundant field in port_id_t Change -qla2xxx: edif: remove redundant field in port_id_t - ER147331 - extract bbc from PLOGI template payload. Change -qla2xxx: Fix buffer-buffer credit extraction error - ERXXXXXX : Split qla2x00_configure_local_loop() Change scsi: qla2xxx: Split qla2x00_configure_local_loop() - ERXXXXXX : SCMR - Add I/O flow control. Change - qla2xxx: SCMR - Add I/O flow control. - 10.02.00.02.a4-k1 BH 07/23/2020 - ER147402 - Do not install nvme auto connect script if OS is installing it. Change - qla2xxx: auto-connect scripts are install based on nvme-cli package. - ERXXXXXX - Fixed return status of nvme fcp request. Change - qla2xxx: Set NVME status code for failed NVME FCP request. - ERXXXXXX - Multi-que support for TMF. Change - qla2xxx: Multi-que support for TMF. - ERXXXXXX ? edif changes Change - qla2xxx: edif: simplify reserve/release of sa_index. qla2xxx: edif: tweak debug log. qla2xxx: edif: adjust ELS resp length. qla2xxx: edif: send logo on app stop. qla2xxx: edif: remove prlo in session deletion. qla2xxx: edif: Fix app stop stall. - ER147298 - USCM "Congestion Warning" counter regression w/.65 driver. Change - qla2xxx: Correct fpin_descriptor definition. qla2xxx: Consolidate EDIF & SCM Purex Calls. - ERXXXXXX - Calculate avg. time taken by different components for IO completion. Change - qla2xxx: Latency measurement patch. - 10.02.00.02.a3-k1 BH 07/16/2020 - ER147348 - Observing firmware dump while running qaucli -g post port isolation. Change - qla2xxx: Don't check firmware state in case of chip is down. - ER147338 - SLES: Driver load failed - modprobe: ERROR: module 'qla2xxx' is unsupported. Change - qla2xxx: Add support for loading external modules on SuSE. - ER147361 - System panic after enabling port isolated during TimeOutReset. Change - qla2xxx: Synchronize the update the host counters using lock. - ER147370 - Hardware Error counter not incrementing for MBX command timeout. Change - qla2xxx: Update hardware error count for various error conditions. - ERXXXXXX - The change is to help in debuggging. Change - qla2xxx: Move some messages from debug to normal log level. - ER147346 - Observed a call trace after port isolation. Change - qla2xxx: Fix the call trace for flush workqueue. - ERXXXXXX - For debug purpose. Change - qla2xxx: Add error counters to debugfs node. - 10.02.00.02.a2-k1 AE 07/10/2020 - ERXXXXXX - qla2xxx: Fix TCM compilation issues. Change - Enabled build of tcm_qla2xxx module and fixed compile issues. - ERXXXXXX - qla2xxx: edif : Added back the app_stop wait and avoid if link is down. Change - Added wait during app stop. - ERXXXXXX - qla2xxx: Set BIT_13 for NVMe Async events. Change - Driver changes to skip SLER for Async event command. - ER147323 - qla2xxx: Correct the check for sscanf return value. Change - Driver updated to check version correctly. - ERXXXXXX - qla2xxx: v2: Add EDIF support. Change - Refactoring EDIF code for modularity. - ER147298 - Congestion Warning/Alarm counters fail to increment Change - Update driver to increment the counters for congestion signals. - 10.02.00.02.a1-k1 AE 06/29/2020 - qla2xxx: Enable IOCB throttling by default. - qla2xxx: Implementation to get and manage host, target stats and initiator port. - qla2xxx: Add SLER and PI control support. - qla2xxx: Do not log message when reading port speed via sysfs - qla2xxx: fix null pointer access. - qla2xxx: Use MPI hang trigger to do PEGTUNE halt. - qla2xxx: Reduce erroneous error in link reset path - qla2xxx: v2: fix stalled N2N reconnect. - qla2xxx: Fix warnings on SLES12SP5. - qla2xxx: Fix compilation issues on SLES15 - qla2xxx: Compilation Fixes for SLES15SP1. - qla2xxx: Debugfs compilation issue fix for RH7.6. - qla2xxx: Fix gcc test compile error output being printed. - qla2xxx: Timestamp device online and offline transitions. - qla2xxx: Add rport fields in debugfs. - qla2xxx: Allow dev_loss_tmo setting for FC-NVMe devices. - qla2xxx: Setup debugfs entries for remote ports. - qla2xxx: Fix edif related compilation issue on RH7.6. - Fixes for compilation on hpe branch - qla2xxx: Compilation fixes for RH8.2 - qla2xxx: Compilation changes for RH7.6 - qla2xxx: Fixes for compilation on RH7.x I - qla2xxx: bsg_job to bsg_job_t - qla2xxx: I Unify source code to work with newer kernels. - qla2xxx: Makefile changes from code-uni-devel-10x. - qla2xxx: qla_edif file changes to compile the driver. - qla2xxx: Fix compilation issues. - qla2xxx: Fix Makefile issue. - qla2xxx: fix compile error - qla2xxx: Use explicit LOGO in target mode - qla2xxx: Add EDIF support. - qla2xxx: Addd edif related files. - qla2xxx: Fix MPI failure AEN (8200) handling. - qla2xxx: SCM - Backport optimizations and style changes from upstream work. - qla2xxx: Fix warning in qla_attr.c file. - qla2xxx: Fix nvme compilation error. - qla2xxx: Fix crash in alloc w/GFP_KERNEL + interrupt - Author : Quinn Tran <qutran@marvell.com> qla2xxx: v2: add iocb resource tracking. - qla2xxx: Fix WARN_ON in qla_nvme_register_hba. - qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime. - qla2xxx: Make tgt_port_database available in initiator mode. - qla2xxx: reduce noisy debug message. - qla2xxx: Fix mailbox Ch erroneous error - qla2xxx: fix login timeout. - qla2xxx: Accomodate for SCM FW attribute bit change. - qla2xxx: post FC event (FPIN) to transport FPIN handler. - qla2xxx: Hide fc_host_fpin_rcv kernel dependency. - qla2xxx: Add changes to compile across various kernels. - qla2xxx: Use active targets to update SCM stats. - qla2xxx: Move SCM functions to qla_isr to keep changes local. - qla2xxx: Code to process FLOGI ACC extended payload. - qedf: Fix compilation issue - revisit. - qla2xxx: SCM Phase 1 Implementation + 2 other patches. - qla2xxx: Enable PUREX passthru post ISP reset. - qla2xxx: Fix hang when issuing nvme disconnect-all in NPIV. - qla2xxx: performance tweak - scsi: qla2xxx: fix fcport null pointer access. - fixup! qla2xxx: Fix unbound NVME response length. - scsi: qla2xxx: Fix unbound NVME response length - qla2xxx: Add host attribute to trigger MPI hang. - qla2xxx: ONEOFF: silent dbg messages for good path io. - qla2xxx: ONEOFF: fix pDIF detection - qla2xxx: Snoop inquiry response atleast 168 bytes to determine proprietary DIF. - qla2xxx: ONEOFF: add debug counters for T10-PI/DIF - qla2xxx: ONEOFF: add MQ support for HP3PAR propritary T10-PI - qla2xxx: HPE 3PAR private T10-PI support. - qla2xxx: Check for fabric_priority flag during login - qla2xxx: use iocb_fabric_priority flag - qla2xxx: Fix QoS name and add debug logs - qla2xxx: Correction to tests for iocb fabric and fcport qos. - qla2xxx: Use ->isp_ops->read_optrom() in qla26xx_read_qos_fcport_table(). - qla2xxx: QoS fcport table index initialization improvement. - qla2xxx: Add QoS fcport table index to speed up search. - qla2xxx: Reduce stack on qos fcport priority routines. - qla2xxx: HPE: Register FDMI QOS - qla2xxx: Add bsg interface for qos lun level bitmask. - qla2xxx: Read E2E QoS fcport priority bitmasks from flash. - qla2xxx: Abstract qos lun level mask for iocb cs_ctl field. - qla2xxx: Add fabric priority qos lun iocb mechanism. - qla2xxx: Implement CT command GFO (Get Fabric Object). - qla2xxx: Add support for fabric priority per target. - qla2xxx: fix mtcp dump collection failure. - qla2xxx: Set Nport ID for N2N - qla2xxx: Fix crash during device discovery. - qla2xxx: Handle NVME status iocb correctly. - qla2xxx: Remove restriction of FC T10-PI and NVME - qla2xxx: serialize fc_port alloc in N2N - qla2xxx: NPIV does not come up after FW dump. - qla2xxx: fix RDP respond data format bug. - qla2xxx: force semaphore on flash validation failure. - qla2xxx: add more FW debug information - qla2xxx: Revert: Disable T10-DIF feature with FC-NVMe during probe - qla2xxx: Update BPM enablement semantics. - qla2xxx: fix FW resource print error. - qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs. - qla2xxx: Ensure flash updates return possible failure status through bsg interface. - qla2xxx: Improved secure flash support messages - qla2xxx: fix flag passing error - qla2xxx: Use FC generic update firmware options routine for ISP27xx. - qla2xxx: Avoid setting firmware options twice in 24xx_update_fw_options. - qla2xxX: Add 16.0GT for PCI String - qla2xxx: Use FW_STARTED macro - qla2xxx: Add fixes for mailbox command - qla2xxx: Fix login IOCB flag - qla2xxx: Save rscn_gen for new fcport - qla2xxx: firmware option 3 is clobbered by speed set - qla2xxx: ISP28xx active FW region - qla2xxx: Add portname to print logs in qla24xx_logio_entry(). - qla2xxx: Correction to MB in-direction selection in qla2x00_echo_test(). - qla2xxx: Correction to selection of loopback/echo test. - qla2xxx: Use endian macros to assign static fields in fwdump header. - qla2xxx: Add Speed in SFP print information - qla2xxx: Fix RDP response size - qla2xxx: Handle cases for limiting RDP response payload length. - qla2xxx: Add deferred queue for processing ABTS and RDP. - qla2xxx: Cleanup ELS/PUREX iocb fields. - qla2xxx: Add devid's and conditionals for 28xx. - qla2xxx: Add vendor extended FDMI additions and amendments. - qla2xxx: Provide separate RDP enable. - qla2xxx: Add vendor extended RDP additions and amendments. - qla2xxx: Add changes in preparation for vendor extended FDMI/RDP. - qla2xxx: Add 2061 PCI ID - qla2xxx: Remove all DIX-0 references - qla2xxx: Add endianizer macro calls to fc host stats. - qla2xxx: Add sysfs node for D-Port Diagnostics AEN data. - qla2xxx: Move free of fcport out of interrupt context. - qla2xxx: Add beacon LED config sysfs interface. - qla2xxx: Add sysfs hooks for FC-NVMe autoconnect - 10.01.00.22-k AE 06/29/2020 - Upstream driver as part of Linux 5.6 - 10.02.14.00-k1 AG 05/21/2025 - - 10.02.14.00.a4-k1 AG 02/27/2025 [FCD-4186] : Device discovery fails on continuous reboot (Hitachi) Resolution : In a fabric topo when there is mismatch in state of login between driver and FW, query FW again and proceed with login Scope : 27xx/28xx Adapters [FCD-XXX] : Make functions local to a file static Resolution : Make functions local to a file static Scope : 27xx, 28xx series Adapters [FCD-XXX] : Remove unused function Resolution : Function qla25xx_set_purex is unused - remove it Scope : All adapters [FCD-4729] : Compilation errors with Sles15sp6 Resolution : Fix compilation errors on Sles15 SP6 Scope : Series Adapters [FCD-4536] : Compilation errors on RHEL10 Resolution : RHEL 10 has rebased to the latest kernel resulting in several build issues. Fix them and ensure that it builds on older kernels as well. Scope : Series Adapters [FCD-4676] : Add support for RH 9.6 (compilation) Resolution : Fix compilation errors on RH 9.6 Scope : Series Adapters [FCD-XXX] : Update README to reflect the supported distros Resolution : Update README to reflect the supported distros Scope : All Adapters Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com> Change-Id: Ic4af035fd48a3137923c7d3590be4271b0a7fd32 commit e22ea0921e20bcf93db0fae2b8dd579005686908 Author: Anil Gurumurthy <agurumurthy@marvell.com> Date: Fri Jan 10 11:06:14 2025 +0530 qla2xxx: Update driver version to 10.02.13.03-k1. - 10.02.13.03-k1 AG 01/10/2025 [FCD-4627] : HPSD5.10-BFS RHEL9.5 system crash on Nimble-HF40 failover test. Resolution : Check for sp being valid, before freeing associated memory Scope : All - 10.02.13.02-k1 MR 01/07/2025 [FCD-4657] : Fix SCSI INQ issue for supporting T10 DIF. Resolution : Replace sp completion with qpair completion call.. Scope : 28XX - 10.02.13.01-k1 MR 01/02/2025 [FCD-1040] : Call scsi done and nvme done with good completion without lock. Resolution : Done changes to move scsi done and nvme done without lock. Scope : 27xx and above - 10.02.13.00-k1 AG 10/22/2024 - - 10.02.13.00.a3-k1 SD 10/09/2024 [FCD-XXX] : Crash seen during load/unload test in a loop Resolution : Delay module unload when there is a fabric scan going on Scope : All adapters [FCD-4193] : SCSI device never recovers after RSCN Resolution : Remove tape specific checks which prevented recovery Scope : All adapters - 10.02.12.01-k1 MR 05/29/2024 [FCD-3465] : Server got crashed while running port toggle test. Resolution : During vport_delete send async_logout explicitly. Scope : 28XX - 10.02.12.00-k1 SD 05/20/2024 - - 10.02.12.00.a5-k1 SD 05/07/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a4-k1 SD 04/25/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a3-k1 SD 03/15/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : SFP cache on legacy adapter Scope : all - 10.02.12.00.a2-k1 SK 02/08/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : Fix NVME + NPIV connect issue Resolution : Initialize irq offset Scope : ALL - 10.02.12.00.a1-k1 QT 01/09/2024 scsi: qla2xxx: Drop redundant pci_enable_pcie_error_reporting() Resolution : Fix RHEL 9.4 compile issue Scope : ALL [FCD-3515] : API support for SFP data cache Scope : 27xx, 28xx [FCD-xxx] : Fix SLES15.6 compile issue Resolution : Remove stale fields Scope : ALL [FCD-3634] : Remove check req_sg_cnt should be equal to rsp_sg_cnt. Resolution : Firmware supports multiple sg_cnt for request and response for CT commands, so remove the redundant check. Scope : All Adapters [FCD-717] : Move FCE Trace buffer allocation to user control Resolution : Modify existing DFS knob to allow user to enable|disable this feature. Scope : Any [FCD-xxx] : Remove del_work work from qla_schedule_sess_for_deletion. Resolution : Remove del_work work from qla_schedule_sess_for_deletion. Scope : All [FCD-xxx] : Additional target mode code cleanup. Resolution : Additional target mode code cleanup. Scope : All [FCD-xxx] : Update copyright information. Resolution : Update copyright information. Scope : All [FCD-xxx] : Remove target code from qla_target files. Resolution : Remove target code from qla_target files. Scope : All [FCD-xxx] : Remove target mode code from initiator specific files. Resolution : Remove target mode code from initiator specific files. Scope : All [FCD-xxx] : Move common code to initiator specific files. Resolution : Move common code to initiator specific files. Scope : All [FCD-3751] : Fix use after free on unload Resolution : Remove duplicate signals on freeing dpc_thread Scope : ALL [FCD-3515] : Caching SFP data Scope : 27xx, 28xx [FCD-xxx] : Exec FW with delay Resolution : Add delay before command retry Scope : 28xx [FCD-xxx] : fix abort in bsg timeout Resolution : Wait for bsg to return before abort exit Scope : ALL [FCD-xxx] : Use QP lock to search for bsg. Resolution : use correct lock to protect search Scope : ALL [FCD-xxx] : Remove SQ in queuecommand Resolution : Remove duplicate code. Scope : ALL [FCD-xxx] : Reduce fabric scan duplicate code. Resolution : Consolidate routines that handle GPNFT & GNNFT. Scope : ALL [FCP-743] : Remove ql2xstay_attach_on_load_failure Resolution : Remove driver parameter used as part of feature test. Scope : 27xx, 28xx - 10.02.11.00-k1 NJ 10/25/2023 [FCD-xxx] : Remove PCI ID 0x2971 Resolution : Remove PCI ID 0x2971 Scope : [FCD-3661] : Remove 8031 from deprecate and unmaintained list. Resolution : Remove 8031 from deprecate and unmaintained list. Scope : 8031 [FCD-3571] : Unable to resume FW dump collection Resolution : send notification to udev Scope : 27xx, 28xx [FCD-3631] : Convert Port disable state to maintenance mode Resolution : Rename state and turn flag indicator Scope : 27xx + 28xx - 10.02.11.00.a8-k1 NJ 10/13/2023 [FCD-3632] : Remove support for FCoE device ids. Resolution : Remove FCoE ids from pci table. Scope : 8xxx [FCD-3624] : Fix optrom version displayed in FDMI Resolution : Populate EFI version Scope : Series Adapters [FCD-3632] : Remove CNA reference from README. Resolution : Remove CNA reference from README. Scope : 8xxx - 10.02.11.00.a7-k1 NJ 09/22/2023 [FCD-3195] : Fix flash read failure Resolution : Check return code for each flash read. Scope : Series Adapters [FCD-3571] : System flood by fw dumps Resolution : udev script to pause fw dump collection Scope : Any [FCD-3566] : Limit FW dump improvement to 27xx + 28xx Resolution : Add filter for 27xx + 28xx adapters Scope : 27xx+ [FCD-3497] : Return ENOBUFS if sg_cnt is more than one for ELS cmds. Resolution : This error is because FW support single sg element for ELS Pass-through IOCB (0x53h). This particular error code will help API and Apps to display appropriate message to the user. Scope : All Adapters [FCD-3510] : RHEL & SLES OOB driver request: deprecate L8/Hilda HW Resolution : Added a frame work to display the message based on device and OS. Scope : L8 and L16 (Hilda and CNA) [FCD-3269] : Init Control Block is dereferenced incorrectly Resolution : Correctly dereference ICB Scope : 20xx [FCD-3421] : Add Support to collect fw_dump on system crash or panic. Resolution : Add Support to collect fw_dump on system crash or panic Scope : 27xx, 28xx - 10.02.11.00.a6-k1 MR 09/08/2023 [FCD-XXX] : Modify error code handling for sfp fw upgrade mbx. Resolution : Modify error code handling for sfp fw upgrade mbx. Scope : 28xx [FCD-XXX] : Block sysfs resets and fw_dump during sfp fw upgrade Resolution : Block sysfs resets and fw_dump during sfp fw upgrade Scope : 28xx [FCP-743] : Block sysfs access during maintenance mode Resolution : Add check for maintenance mode. Scope : Any [FCD-3506] : Fix double free of dsd_list during driver load. Resolution : add pointer check before access Scope : Any - 10.02.11.00.a5-k1 MR 08/18/2023 [RH BZ 2039422] : NVMe-FC kernel crash during reload driver test Resolution : validate nvme_local_port correctly Scope : Any [FCD-XXX] : Fix for potential Null pointer dereferenced Resolution : Check before dereferencing pointer Scope : Any [FCP-743] : Enable driver attach to bad HW Resolution : turn on ql2xstay_attach_on_load_failure option Scope : 27xx, 28xx - 10.02.11.00.a4-k1 MR 08/11/2023 [FCD-xxx] : Update README file for zio information Resolution : Update readme file with zio information Scope : Any [FCD-3415] : Std-DIF is not working with HPe K1 driver Resolution : Reset the protect bit in the INQ response only when pDIF is enabled and negotiated. Scope : 26xx/27xx/28xx - 10.02.11.00.a3-k1 AG 08/03/2023 [FCP-743] : Allow only selective BSG requests in maintenance mode Resolution : Allow certain BSG to go through during maintenance mode Scope : Any [FCP-743] : FW dump improvement Resolution : Improve data capture Scope : 27XX, 28XX [FCD-3252] : Unable to act on RSCN for port online. Resolution : Clear RSCN flag only when driver is acting on the notification Scope : Any [FCD-xxx] : 32 Bytes CDB Resolution : Use Type 6 IOCB for CDB bigger than 16Bytes Scope : Any Unit Test : i) force IO to use Type6 only for over the weekend run. ii) force error path(s) to make sure no crash. [FCD-xxx] : Move resource to allow code reuse. Resolution : relocate dsd_list to qpair Scope : Any - 10.02.11.00.a2-k1 AG 07/27/2023 [FCD-3411] : CS_DMA Error observed while running DIF IO Resolution : While running DIF enabled IO, a CS_DMA error was observed. A FW dump is needed to better debug this. So take a FW dump on encountering this. Scope : 27xx/288 series of adapters [FCD-3406] : Modifiy default zio threshold value. Resolution : Modifiy default zio threshold value. Scope : 27xx/28xx Series Adapters [FCD-3314] : Delay IO Abort on PCI error Resolution : On detection of PCI error, allow IO's to wind down. Scope : Any [FCD-3314] : Fix system crash due to bad pointer access Resolution : Check SRB type before access. Scope : 27xx+ - 10.02.11.00.a1-k1 AG 07/14/2023 - FCP-749: qla2xxx: Add support for build for RH 9.3 and RH 8.9 distro Resolution : Build on RH 9.3 was failing owing to change of definition of fc_host_fpin_rcv and removal of DID_TARGET_FAILURE. Fix part of it by updating to latest upstream code. Scope : 27xx/28xx series of adapters - FCD-3302 : During unload Error detected messages is seen. Resolution : Change the wording of the message as its not an error. Scope : Series Adapters - FCD-3293 : Initiator sever getting crashed after LOGO. Resolution : Fix double free of fcport Scope : Any - Revert "scsi: qla2xxx: Change default ZIO threshold." This reverts commit 8812bcc1b7a25494ec8755ff3b61412a9993ff5b. The ZIO threshold now is 64. - FCD-xxx : Fix unreachable code Resolution : Remove dead code Scope : 28xx+ - FCD-3232 : Potential risk of double free pointer detected in Coverity scan by ran by Citrix Resolution : NULL the pointer after first free. Scope : All - 10.02.10.00-k1 SK 06/14/2023 Non-alpha build - 10.02.10.00.a2-k1 BH 05/12/2023 - FCD-3140: qla2xxx: Fix command flush on cable pull. Changes: Add wait for commands to return. - FCD-XXX: qla2xxx: NVME|FCP prefer flag not being honored. Changes: Reread prefer flag on chip reset - FCD-XXX: qla2xxx: Update readme file - 10.02.10.00.a1-k1 BH 05/02/2023 - FCD-XXX: qla2xxx: Update Copyright Changes: Update Copyright for Marvell. - FCD-XXX: qla2xxx: Update manufacturer detail Changes: Update manufacturer detail to "Marvell" - FCD-3140: qla2xxx: Host crash during StressAndHostPortReset test Changes: Remove unused nvme_ls_waitq wait queue. - FCD-XXX: qla2xxx: [RH-BZ 2167274]: Wait for io return on terminate rport. Changes: dd wait to terminate_rport_io - 10.02.09.00.a11-k1 BH 03/27/2023 - FCD-XXX: qla2xxx: Add link down + logo rx stat counts Changes: Add counters to track link down and Logo receive. - 10.02.09.00.a10-k1 BH 03/17/2023 - FCD-XXX: qla2xxx: Support for update SFP firmware of ACCELINK Changes: [New Feature] Support for update SFP FW of ACCELINK WTD 64G - FCD-717: qla2xxx: Split FCE|EFT trace control Changes: Split buffer alloc and enable of feature into individual step. - BZ-2093878: qla2xxx: perform lockless command completion in abort path Changes: Perform lockless command completion in abort path - 10.02.09.00.a9-k1 BH 03/06/2023 - FCD-2390: qla2xxx: Fix N2N stuck connection. Changes: Clear the blocking flag. - FCD-2496: qla2xxx: Prevent command send on chip reset Changes: Check for chip reset before sending IOCB. - FCD-2035: qla2xxx: Fix mem access after free. Changes: Remove access of memory - FCD-2720: qla2xxx: Move cmd_to_req_q latency counter before processing response. - FCD-XXX: qla2xxx: Update readme file for current program - 10.02.09.00.a8-k1 BH 02/27/2023 - FCD-2585: qla2xxx: Remove unsupported ql2xenabledif option. Changes: Removed unsupported ql2xenabledif=1 option and validate the user input. - FCD-2305: qla2xxx: Error code did not return to upper layer Changes: Preserve error code from TMF and return it to upper layer. - FCD-2035: qla2xxx: fix inconsistent TMF timeout. Changes: Allow TMF error to return to upper layer without session tear down. - FCD-2035: qla2xxx: Fix TMF leak through. Changes: Check for chip reset or session change before sending Task management. - 10.02.09.00.a7-k1 BH 02/17/2023 - FCD-2858: qla2xxx: USCM: Check for vp_idx before setting EDC and RDF set flags. Changes: Add check for vp_idx before setting EDC and RDF set flags when processing RIDA. Revert patch: - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition. - 10.02.09.00.a6-k1 BH 02/13/2023 - FCD-2750: qla2xxx: IO's are failing on Standard DIF enabled 3PAR LUN Changes: Revert an offending patch and work on an issue with upstream. - 10.02.09.00.a5-k1 BH 02/06/2023 - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition Changes: Remove EDC and RDF set flags on Report ID Acquisition. - FCD-2879: qla2xxx: Compilation errors on SLES15SP5 Beta3-202301 Changes: Write generic code to find tag of scsi cmnd - FCD-2846: qla2xxx: Correct bsg_reply size in bsg interface Changes: Fix the bsg_job->reply_len with size of "struct fc_bsg_reply" - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the invariant expression in the condition - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the expression flogi_acc_pld_remaining == 0 - FCD-XXXX: qla2xxx: Changes of logs level for SFP temperature monitoring - 10.02.09.00.a4-k1 BH 01/29/2023 - FCD-2308: qla2xxx: Add bsg call to read port information Changes: Add bsg interface to allow app to read remote port information. - FCD-XXX: qla2xxx: KW-97439: unreachable code Changes: Return void if return value is not needed - FCD-XXX: qla2xxx: Add logs for SFP temperature monitoring Changes: Add debug log for Temperature Alert (8070h) Asynchronous Event - 10.02.09.00.a3-k1 BH 01/19/2023 - FCD-XXX: qla2xxx: Add support of RHEL9.2 - FCD-XXX: qla2xxx: Add support of RHEL8.8 - FCD-XXX: qla2xxx: Add support of SLES15 SP5 - FCD-2800: qla2xxx: Add support of OpenEuler-22.03 - 10.02.09.00.a2-k1 BH 01/10/2023 - FCD-XXX: qla2xxx: kw: unreachable code, SRB type is 0 just before latency counter incremented. Changes: SRB type is 0 just before latency counter incremented. - FCD-XXX: qla2xxx: kw: reset current_topology much later Changes: Reset current_topology much later on detecting - FCD-XXX: qla2xxx: kw: unreachable code, CS_COMPLETE is 0 and its already checked. Changes: Remove unreachable - FCD-XXX: qla2xxx: kw: Checking for port_state always yields zero Changes: Instead of bitwise AND check for port_state directly - FCD-1569: qla2xxx: Fix fw resource tracking Changes: Use global counter - FCD-XXX: qla2xxx: [ER-144639]: Flush mailbox commands on chip reset Changes: Use lock to prevent race condition. - FCD-2735: qla2xxx: USCM-VL: NVRAM VL disabled logins with extend FLOGI (VL enabled) Changes: Reset the spl. features control block flag to avoid logging in with ER_RDY. - FCD-XXX: qla2xxx: klockwork: Fix buffer over flow Changes: Use correct buffer size. - FCD-XXX: qla2xxx: EDIF: kw: remove unnecessary bit field - FCD-2563: qla2xxx: Turn off noisy message log. - FCD-XXX: qla2xxx: kw: remove dead code in qla24xx_config_rings - 10.02.09.00.a1-k1 BH 01/10/2023 - FCD-717: qla2xxx: allow FW dump extraction if load fail Changes: Add knob to force driver to stay attached to the fail adapter. - FCD-717: qla2xxx: Initialize FW buffer size with seed value Changes: Initialize FW Buffer size with seed value - FCD-XXX: qla2xxx: klockwork: Remove QLA_COMMAND_ERROR check in qla2x00_execute_fw. Changes: Remove the unnecessary QLA_COMMAND_ERROR check - FCD-2390: qla2xxx: Fix session hang in gnl Changes: Clear this flag to prevent blockage. - FCD-2390: qla2xxx: Fix erroneous link up failure Changes: Set fw_started flag early to prevent interrupts being dropped - FCD-2496: qla2xxx: Fix command flush during TMF Changes: Wait for commands flush before closing TMF - FCD-2035: qla2xxx: Limit TMF to 8 per function Changes: Limit TMF to 8 per function - FCD-XXX: qla2xxx: Add NVMe Disconnect support. Changes: Add support for NVMe Disconnect feature. - FCD-XXX: qla2xxx: Modify qla27xx_copy_fpin_pkt to support PURLS IOCB. Changes: Modified qla27xx_copy_fpin_pkt to support both PUREX and PURLS IOCBs. - FCD-717: qla2xxx: Adjust iocb resource on qpair create Changes: Add call to readjust iocb + exchange limit. - FCD-2390: qla2xxx: Fix deletion race condition Changes: Move check field behind lock - FCD-XXX: qla2xxx: klockwork: Pointer checked for NULL at linx x will be dereferenced at linx x+y. Changes: Remove the unnecessary Null check. The pointer will likely be valid. - FCD-XXX: qla2xxx: Observed call trace in smp_processor_id() with debug kernel Changes: Use raw_smp_processor_id API - FCD-2275: qla2xxx: USCM: Cleanup code related to IOPS based throttling Changes: IOPS and BW based throttling is not used. Remove those code. - FCD-2273: qla2xxx: USCM: Code cleanup w.r.t module params (ql2x_scmr_flow_ctl_tgt, ql2x_scmr_flow_ctl_host) Changes: Remove the redundant module parameters - FCD-2408: qla2xxx: USCM: Driver doesn't honor the adapter port Restore Default Settings Changes: Update the nvram values to the host as well as fcport - FCD-2363: qla2xxx: USCM: Slow Queue usage changes Changes: Use Slow queue only under specific scenarios - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Don't increment the counter for under-run. - FCD-2291: qla2xxx: Erroneous link down. Changes: Allow adapter reset to complete before discovery - FCD-2035: qla2xxx: Fix hang in task management Changes: Bail out of TMF on error - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path - FCD-XXX: qla2xxx: USCM: Debug log message improvement Changes: Log target WWPN for peer congestion - FCD-2164: qla2xxx: Fix stall session after app start Changes: Use session delete to avoid the accidental clearing of scan_flag - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Check fcport state before invoking the mailbox - FCD-XXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: Set throughput baseline on 1st FPIN - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix parsing the fpin when multiple descriptors are present - FCD-XXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCD-XXX: qla2xxx: USCM: Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: Fix for KW-97392 Changes :Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: Remove dead code - flagged by klocwork - FCD-847: qla2xxx: fixup: Fix exchange over subscription. - FCD-2434: qla2xxx: Fix crash when IO abort times out - FCD-XXX: qla2xxx: Rearrange scm rx path handling code. - 10.02.08.01-k1 BH 09/28/2022 - FCD-2392: Fix initrd image creation failure in OpenEuler, Kylin and UOS Changes: Add support for creating initrd image on openEuler, Kylin and UOS - 10.02.08.00-k1 BH 09/16/2022 - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Residual under-run is not an interface error, hence no need to increment that count. - FCD-2291: qla2xxx: Fix erroneous link down. Changes: Allow adapter reset to complete before any scan can start. - FCD-2035: qla2xxx: Fix hang in task management Changes: Add additional error check at various point - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced. - 10.02.08.00.a7-k1 BH 08/22/2022 - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path. - FCD-2164: qla2xxx: USCM: Fix stall session after app start Changes: Prevent accidental clearing of flag that blocks re-login - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset. - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Heck fcport state before invoking mailbox - FCDXXX: qla2xxx: USCM: Debug log message improvement - 10.02.08.00.a6-k1 BH 08/09/2022 - FCDXXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: if VL switchreduces the throughput below 50%, we would not throttle any further. - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix the FPIN parsing to take into account multiple descriptors. - FCDXXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCDXXX: qla2xxx: USCM:Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..10 - 10.02.08.00.a5-k1 BH 07/29/2022 - FCD-XXX: qla2xxx: klocwork: Possible Null Pointer Dereference Changes: Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: USCM: Fix mqueuecommand return code during throttle down request. - FCD-XXX: qla2xxx: Revert klockwork: Fix buffer overrun - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h - FCD-2035: qla2xxx: Fix Task Mgmt Cmd fail due to unavailable resource Changes: Limit TM commands to 8 per target. - 10.02.08.00.a4-k1 BH 07/23/2022 - FCD-847: qla2xxx: Fix exchange over subscription. Changes: check for exchange availability before command submission - FCD-XXX: qla2xxx: Remove unintended flag clearing Changes: Remove unintended flag clearing. - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h Changes: Add wait for completion of Marker! - FCD-XXX: Fix performance dip due to lock contention Changes: Save the allocated memory for reuse and avoid the lock - FCDXXX: qla2xxx: USCM: Do not send EDC and RDF for NPIV ports Changes: Disable sending USCM ELS for vports - FCDXXX: qla2xxx: USCM: VL: Do not set target speed to 1G for slow lane Changes: Do not set the target speed while changing lanes. - FCD-2012: qla2xxx: Throttling up messages seen when profile is changed Changes: Set the new profile for each fcport (along with the host). - FCD-XXX: qla2xxx: USCM: VL - Clean up FLOGI_ACC parsing Changes: structure that could be used to parse the FLOGI_ACC by using offsets - FCD-1990: qla2xxx: Fix nvram load config error Changes: Remove re-definition of port flags while enabling virtual lane support - FCD-XXX: qla2xxx: USCM:VL, I/O does not move back to the normal lane Changes: Check if I/O throttling is being done, before deciding to move the normal lane. - FCD-XXX: qla2xxx: Fix stall login Changes: Reset session state to allow relogin logic to re-drive the connection. - FCD-847: qla2xxx: Fix exchange over subscription for mgt cmd. Changes: would check for exchange availability before command submission. - FCD-847: qla2xxx: Fix exchange over subscription. Changes: would check for exchange availability before command submission. - FCD-XXX: qla2xxx: relocate/rename vp map. - FCD-XXX: qla2xxx: Klocwork: Fix for Unexpected type of a scan function parameter - 10.02.08.00.a3-k1 BH 07/01/2022 - FCD-1818: qla2xxx: Fix call trace in debug kernel due to missing spinlock init Changes: Fix the call trace by initializing trace lock. - FCD-1923: qla2xxx: USCM: VL - After disabling VL via CLI, status shows "Non-operational" Changes: Return VL status appropropriately - FCD-1922: qla2xxx: Fix discovery issues in FC-AL topology Changes: Checks FC loop map when Get ID list returns no device - FCD-1831: qla2xxx: Fix link failure in NIPV environment. Changes: Remove NPIV host from directly being able to chip reset. - FCD-XXX: qla2xxx: Fix DMA-API call trace on NVME LS requests with debug kernel Changes: Remove DMA mapping from the driver - FCD-XXX: qla2xxx: Fix KASAN use-after-free warning in qla24xx_sp_unmap Changes: Remove stale fcport access in qla2x00_rel_sp - FCD-XXX: qla2xxx: Fix KASAN out-of-bounds warning in qla_update_sp Changes: Size for memcpy was corrected to use the right length. - FCD-XXX: qla2xxx: Fix imbalance vha->vref_count Chnages: Add an extra ref count for the task management paths. - FCD-XXX: qla2xxx: Tweak Latency measurement Changes: Move the time read further ahead to the start of queuecommand and later to the point where it is just before scsi_done. - FCD-XXX: qla2xxx: klockwork: Silent superfluous warning. Changes: Remove superfluous Null check. - FCD-XXX: qla2xxx: klockwork: Fix buffer overrun Changes: Replace structure name to allow proper size calculation - FCD-XXX: qla2xxx: Remove dead code (GNN ID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code (GPNID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code. Changes: Removing drport field and FCPORT_UPDATE_NEEDED, and EDIF_TICK_NEEDED signals - FCD-XXX: qla2xxx: Do not select slow queue if USCM is enabled Changes: Do not select slow queue whilie initializing cpu map - FCD-XXX: Select HW queue depending on Tx CPU Changes: Select qpair which is in correlation with Tx CPU - FCD-XXX: qla2xxx: Add support for displaying I/O throttle information Changes: Display the driver I/O throttle information along with VL information - FCD-XXX: qla2xxx: USCM: Throttle only R/W commands for NVME Changes: Throttle only read/write IOs. - Bring back following reverted changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.08.00.a2-k1 BH 06/19/2022 - FCD-XXX: qla2xxx: klockwork - Check valid rport returned by fc_bsg_to_rport Changes: Check valid rport returned by fc_bsg_to_rport - FCD-XXX: qla2xxx: klockwork - Check for a valid fcport pointer Changes: Add a check for a valid fcport pointer at the time of exit - FCD-XXX: qla2xxx: klockwork - Move fcport NULL check to avoid dereference Changes: Move the fcport NULL check to avoid the dereference. - FCD-1883: qla2xxx: USCM: Adapter shows "RDF Complete" when Link is down Changes: Reset the flag, so that when USCM is negotiated, the CLI shows the correct status - FCD-1846: qla2xxx: USCM: A log message while clearing stats Changes: Add a log message while clearing USCM stats - FCD-XXX: qla2xxx: USCM: VL-Reset FC device virtual lane priority to normal on a port flap Changes: Reset the virtual lane to normal on a port flap, ISP reset - FCD-XXX: qla2xxx: USCM: VL-Set target congestion before switching lanes Changes: Set the target state before the lane switch. - FCD-1752: qla2xxx: USCM: VL-Sysfs does not show Virtual Lane as enabled Changes: extended flogi_acc can also be parsed correctly. - FCD-1652: qla2xxx: Check if port is online before sending ELS Changes: Check if port is online before sending ELS - FCD-XXX: scsi: qla2xxx: Synchronize rport dev_loss_tmo setting - 10.02.08.00.a1-k1 BH 05/27/2022 - FCD-XXX: qla2xxx: USCM: Virtual Lane, Fix PUN handling Changes: Have a default priority range for each lane and ensure that the range is programmed correctly - FCD-XXX: qla2xxx: USCM: Support for Virtual Lanes Changes: Enable Virtual Lane support for Cisco switch - 10.02.07.00-k1 BH 05/27/2022 - Non-alpha build - 10.02.07.00.a19-k1 BH 05/21/2022 - FCD-XXX : qla2xxx: USCM: Throttling is not honored for NVMe Changes: Enable NVMe READ/WRITE commands to be throttled - FCD-XXX: qla2xxx: USCM: Add counters to track directional throttling Changes: Add sysfs counters to have stats displayed for busy status returns. - FCD-1801: qla2xxx: USCM: CP reads go to zero while doing directional throttling Changes: Take into account the directional queue depth while returning a busy status to the stack. - FCD-1809: qla2xxx: USCM: Restoring USCM Profile to default result in driver - FCD-1798: qla2xxx: USCM: Profiles are not honored for peer congestion Chnages: Apply the profile to each target (fcport) when the profile is changed. Reverting the following changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.07.00.a18-k1 BH 05/12/2022 - FCD-1484: qla2xxx: Manufacturer details should be "Marvell Semiconductor, Inc." Changes: Update Manufacturer details to indicate Marvell Semiconductors - FCD-XXX: qla2xxx: USCM: Throttle only read and write commands Changes: Throttle only read and write commands. - FCD-XXX: qla2xxx: USCM: Do not clear throttle for Clear Cong FPIN. Changes: Do not clear throttle when Clear Congestion FPIN is received. - FCD-XXX: qla2xxx: USCM: Change default profile to Monitor Changes: Set the default throttle profile as Monitor. - FCD-XXX: qla2xxx: Fix few issues reported by klocwork tool - 10.02.07.00.a17-k1 BH 05/06/2022 - FCD-1522: qla2xxx: USCM: Throughput drops to zero in Monitor mode Changes: Restore qdepth based on monitor mode - FCD-1315: qla2xxx: Fix erroneous mailbox timeout after pci error inject. Changes: Clear wait for MB interrupt flag to prevent stale MB completion arriving - FCD-1424: Remove verbose IO debug messages Changes: Remove the IOCB debug messages for every IO - FCD-XXX: Support for NVMe parameters in Auxiliary Image Status Changes: Added new structure member, bit define and image status check. - 10.02.07.00.a16-k1 BH 04/08/2022 - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - FCD-1221: qla2xxx: USCM: Switch does not send FPINs after a EDC re-negotiation Changes: Send Link Service Request Information wih the EDC response, along with the other descriptors. - 10.02.07.00.a15-k1 BH 03/25/2022 - FCD-1249: qla2xxx: edif: Fix dropped IKE message. Changes: Fixes IKE message being dropped due to error in processing Purex IOCB and Continuation IOCBs. - FCD-1457: qla2xxx: Zero undefined mailbox IN registers Changes: Set zero to unuse register's value while requesting a new MB command. - FCD-1425: qla2xxx: USCM: Seconds since last event showing incorrect value Changes: Calculate delta time correctly - FCD-1287: qla2xxx: Fix incorrect display of max frame size. Changes: Save off the field of interest into separate location and convert into words. - FCD-XXX: qla2xxx: Fix memory leak when reading tgt_port_database debugfs file - FCD-XXX: qla2xxx: USCM: Do not reset SCM stats on a link bounce/ISP reset - 10.02.07.00.a14-k1 BH 03/14/2022 - FCD-XXX: qla2xxx: Fix losing FCP-2 targets on long port disable with IOs Changes: Fix this by accepting RSCN when the device is not online. - FCD-XXX: qla2xxx: Fix losing target when it reappears during delete Changes: Fix the issue by adding state checks before proceeding. - FCD-XXX: qla2xxx: Fix losing FCP-2 targets during port perturbation tests Changes: Fix was to ignore delete for FCP-2 devices in certain sequence. - FCD-119: qla2xxx: Fix crash due to stale srb access around IO timeouts Changes: Ensure srb is either returned during error IO timeout error escalation. If that is not possible fail the escalation path. - FCD-1132: qla2xxx: HPE3PAR: Fix IOCB resource count leak Changes: Decrement FW IOCB resource count. - FCD-1132: qla2xxx: Turn off MQ for 8G adapter. Changes: For 8G adapter, multi queue was enabled accidentally. - FCD-1385: Wind down adapter after pcie error. Changes: Detect the PCIE error and returns all IO's to upper layers. - FCD-1412: qla2xxx: Reset Congestion Warning/Alarm signals count. Changes: Reset signals at every signal check boundary (1 sec). - 10.02.07.00.a13-k1 BH 02/17/2022 - FCD-1353: qla2xx: a12/a11 driver compilation gives warning messages Changes: Fix the fall through warning - FCD-1342: qla2xxx: SL12SP5 a12 driver compilation issue observed Changes: fallthrough macro is defined based on gcc version. - 10.02.07.00.a12-k1 BH 02/09/2022 - FCD-XXX: qla2xxx: Reset USCM stats/state and throttling on RSCN Changes: Reset USCM stats on getting an RSCN indicating a target port down. - FCD-XXX: qla2xxx: Increase max limit of ql2xnvme_queues Changes: Increase max limit of ql2xnvme_queues to (max_qpair-1) - FCD-478: qla2xxx: Fix missing devices on a LOGO from F-Port Changes: A call to logo all ports is made upon a F-Port LOGO. - FCD-XXX: qla2xxx: Move NVMe traffic to the slow queue on target congestion Changes: Steer the NVMe traffic to the slow Q on encountering target congestion - FCD-348: qla2xxx: edif: Fix slow session tear down. Changes: As a work around, driver would trigger a session tear down where it tell the local authentication application to also tear down. - FCD-XXX: qla2xxx: edif: Tweak debug log. Changes: Print AUTH ELS header to assist in debugging session's state of authentication app. - FCD-207: qla2xxx: Fix stuck session of prli reject Changes: Remove the stale code that cause the unintentional short cut. - FCD-1197: qla2xxx: Throttling up is seen when port is down Changes: Reset the stats/congestion state and the throttling algorithm on a link down event. - FCD-348: qla2xxx: Reduce false trigger to login Changes: Reduce the extra trigger to prevent multiple login to the same session. - FCD-207: qla2xxx: edif : Reduce N2N thrashing at app_start time Changes: make sure the old session is torn down before triggering a relogin. - FCD-207: qla2xxx: Fix laggy FC remote port session recovery Changes: allows the higher priority error recovery to run first before running the lower priority heart beat check. - FCD-XXX: qla2xxx: edif: Fix no logout on delete for n2n Changes: Set a flag to turn on implicit logout early in the session recovery to make sure it would go out in case of error. - FCD-348: qla2xxx: edif: fix session thrash 2 Changes: prevents prli from going out before authentication app gives the ok - FCD-348: qla2xxx: edif: tear down session if keys has been removed Changes: If all keys for a session has been deleted then trigger a session tear down. - FCD-348: qla2xxx: edif: fix no login after app start Changes: Add a re-login trigger to relogin. - FCD-207: qla2xxx: Fix hang due to session stuck Changes: Break the requeue cycle and exit. The session deletion code will trigger a session relogin. - FCD-348: qla2xxx: edif: reduce disruption due to multiple app start Changes: Driver will skip over session tear down if app start is seen more than once. - FCD-348: qla2xxx: edif: send logo for unexpected ike msg Changes: Terminate/cleanup the AUTH ELS exchange.Follow with a pass through LOGO. - FCD-348: qla2xxx: edif: Fix IO timeout due to over subscription Changes: Track IOCB resources to prevent over subscription of IOCB resources - FCD-207: qla2xxx: edif: fix n2n login retry for secure device Changes: Add a few more login retries to revive the connection. - FCD-1205: qla2xxx: Fix disk failure to rediscover Changes: Set the online state before reporting to UL of the availability of the session. - FCD-207: qla2xxx: Fix n2n inconsistent plogi Changes: Delete the session to restart the connection, where ELS pass through PLOGI would be used consistently. - FCD-1267: qla2xxx: Fix crash during module load unload test Changes: Driver correctly freeing a pre-allocated structure for purex packet handling - FCD-XXX: qla2xxx: Fix missed DMA unmap for NVME ls requests. Changes: Add an unmap call during ELS completion. - FCD-1266: qla2xxx: Fix loss of NVME namespaces after driver reload test Changes: Calling the localport registration under a mutex - FCD-1212: qla2xxx: Host does not retry RDF when retries are exhausted and there is an incoming RDF Changes: Reset the SCM ELS counters to zero once an RDF is received. - FCD-XXX: qla2xxx: Restrict CPU-qpair mapping to work for NVMe only - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. - FCD-XXX: qla2xxx: SCM: Add a bitmap for FPIN events. - 10.02.07.00.a11-k1 BH 01/17/2022 - FCD-738: Fix T10 DIF performance on high end setup Changes: Added high performing CRC-1 interface - FCD-1182: qla2xxx: Fix initrd build error on RHEL 9 Changes: Updated the build script specific to RHEL 9 - FCD-XXX: qla2xxx: Fix incorrect latency counter display Changes: Fix this by ignoring I/Os with unusually high latencies. - FCD-207: qla2xxx: Fix n2n discovery issue with secure target Changes: On app_start, driver will reset the login retry attempt count. - FCD-1180: qla2xxx: Use correct feature type field during rffid processing Changes: Driver sends RFF_ID for initiator type 28 i.e. NVMe insteads of SCSI two times - FCD-1159: qla2xxx: Host doesn't retry the RDF/EDC when jammed with idle/CRC Changes: Wake up the DPC thread from the timer context when EDC/RDF needs to be - FCD-XXXX: qla2xxx: Build module with "-mindirect-branch=thunk-extern" option on RHEL 9 - 10.02.07.00.a10-k1 BH 01/06/2022 - FCD-XXX: qla2xxx: Support for changes in kernel 5.6 and above(rhel9.0) Changes: Changes made specific to rhel9.0 - FCD-1136: qla2xxx: Throttling occurs even when USCM is disabled via CLI Changes: Update flags that control USCM features, correctly on ISP reset - FCD-1160: USCM continues to be active even if RDF response is jammed (and failed) Changes: USCM flags are updated properly when port toggle and RDF completion happen - 10.02.07.00.a9-k1 BH 01/03/2022 - FCD-1154: qla2xxx: Fix incorrect reporting of task management failure Changes: Corrected endianness. - 10.02.07.00.a8-k1 BH 12/23/2021 - FCD-814 : qla2xxx: Add a new v2 dport diagnostic feature. Changes: Buffer size is increased to 1024 bytes and handle START/RESTART command received from SDMAPI. - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. Changes: Ramp up to faster initially, to get closer to the sweet spot quicker. Be less prone to operating at lower bandwidth in case of a sudden workload spike. Operate more conservatively (prioritize self over the network). - FCD-XXX: qla2xxx: Do not track SCM stats for all ports in the zone Changes: Track SCM stats just for the host and the target - FCD-XXX: qla2xxx: Stats for FPIN with event type "Lost Credit" not incremented. Changes: Add incrementing of "Lost Credit" stats. - FCD-684: qla2xxx: Fix link down when connected to AG fabric with FAA enabled Changes: Remove setting PUN and VL support bits in init control block. - FCD-1004: qla2xxx: Debug message improvement when changing SCM profile. Changes: Use profile names when changing profiles - FCD-868: qla2xxx: lockdown: "Unsupported Firmware" message Changes: checked different BITs for checking lockdown feature. - FCD-682: qla2xxx: tcm_qla2xxx driver load fails with "Invalid argument" error Changes: As tcm_qla2xxx is untested/unused, make it a dummy driver and reduce unncessary noise created by this. - FCD-886: qla2xxx: Hard Lockup on Unload/Load task with serial log enabled Changes: Hard lockup is seen because serial console driver crashed because of excessive logging. It was finalized to document this as known issues. - FCD-XXX: qla2xxx: Apply USCM profile change immediately - 10.02.07.00.a7-k1 BH 11/05/2021 - FCD-926: qla2xxx: lockdown: lower debug severity messages - FCD-824: qla2xxx: lower debug severity message for fw lockdown Changes: This patch lower the severity of various log messages. - FCD-XXX: qla2xxx: Send LS_ACC for an incoming RDF Changes: Send the LS_ACC and the new RDF separately - FCD-721: qla2xxx: Set Max queue depth based on data direction. Changes: Max q depth for Initiator tracks Reads (per port) and Fcport tracks Writes (per fcport). - FCD-701: qla2xxx: Fix device reconnect in loop topology Changes: Fix by taking the main login path that acquires device handle. - FCD-XXX: qla2xxx: Add ql2xnvme_queues module parameter to configure number of NVME queues - 10.02.07.00.a6-k1 BH 10/08/2021 - FCD-786: Shown wrong FDMI data for 64G adaptor Changes: qla2xxx: Corrected transmission speed mask values for FC - FCD-717: add retry for exe fw Changes: qla2xxx: Driver will retry Exec FW command up to 4 retries - FCD-XXX: qla2xxx: Compile out map queue changes if present in nvme-fc - 10.02.07.00.a5-k1 BH 10/01/2021 - FCD-740: Fix scheduling while atomic Changes: qla2xxx: schedule the call to fc_remote_port_delete in non-interrupt context - FCD-691: Fix premature hw access after pci error Changes: qla2xxx: Check error condition still persist and/or wait until the OS to give the resume signal - FCD-756: Fix excessive messages during device logout Changes: qla2xxx: disable printing IO error messages by default - FCD-XXX: qla2xxx: abort fw dump if soft reset fail - FCD-XXX: qla2xxx: USCM: Retry USCM ELS for Logical busy error code - FCD-XXX: qla2xxx: USCM: USCM profile reset to Driver defaults - FCD-XXX: qla2xxx: Fix warning message due to adisc is being flush at /var/log/messages - 10.02.07.00.a4-k1 BH 09/20/2021 - FCD-721: Revert code that keeps track of queue-depth directionally. Reason: Observing issue while q-depth accounting - FCD-XXX: Cleanup stale code. Changes: qla2xxx: Remove unused experimental code that uses explicit PRLO as a way to tear down session. - FCD-XXX: edif: remove old doorbell interface Changes: qla2xxx:driver has implemented a new doorbell mechanism via bsg. - FCD-348: edif: add retry for els pass through Changes: qla2xxx: edif: Add additional retries to reduce higher level recovery. - FCD-XXX: edif: Synchronize NPIV deletion with authentication application Changes: qla2xxx: Notify authentication application of a NPIV deletion event is about to occur. - FCD-XXX: edif: Fix potential stuck session in sa update Changes: qla2xxx: Set flag properly for any attempt to relogin. - FCD-704: The external flag for tcm_qla2xxx was not set. qla2xxx: Add tcm_qla2xxx to externally supported module list. - 10.02.07.00.a3-k1 BH 09/08/2021 - FCD-XXX: qla2xxx: edif: wait for app to ack on sess down Changes: On session deletion, wait for app to acknowledge before moving on. - FCD-XXX: qla2xxx: edif: fix edif bsg Changes: Properly fill out the reply_payload_rcv_len field. - FCD-XXX: qla2xxx: edif: fix inconsistent check of db_flags Changes: Replace value check with bit flag check. - FCD-XXX: qla2xxx: edif: increase ELS payload Changes: Adjust memory buffer size to be able to handle max ELS payload. - FCD-343: qla2xxx: turn off target reset during issue_lip Changes: driver sends additional target reset to remote device before resetting the link. - FCD-XXX: qla2xxx: edif: Reduce Initiator-Initiator thrashing. Changes: Reduce unnecessary stress for authentication application to deal with unused connections. - FCD-XXX: qla2xxx: fix gnl list corruption Changes: move lock deletion behind lock. - FCD-XXX: qla2xxx: edif: flush stale events and msgs on session down Changes: Prevents authentication application from having to process stale data. - FCD-XXX: qla2xxx: edif: reduces thrashing of the connection. - FCD-XXX: qla2xxx: edif: tweak trace message - FCD-XXX: qla2xxx: edif: fix app start delay - FCD-XXX: qla2xxx: USCM: Handle SCM ELS from switch - FCD-XXX: qla2xxx: edif: fix app start fail - 10.02.07.00.a2-k1 BH 09/02/2021 - FCD-156: qla2xxx: 3PAR: Fix out of bound mem access Changes: Add additional check to make sure the range of memory - FCD-624: qla2xxx: Source driver gives compilation error on RHEL8.5 Changes: Offending code on tcm_qla2xxx module has been removed - FCD-xxx: qla2xxx: Fix use after free Changes: Would check for command is aborted / completed by FW before exiting the call. - ER148553: qla2xxx: relogin during fabric disturbance Changes : Set the scan_need flag to indicate a session - FCD-464: qla2xxx: Fix race between timeout handler and completion handler Changes: One reference is taken for the normal code path and one for the timeout path - FCD-453: Fix FC-NVME register localport failure. Changes: Module initialization is added to nvme_fc_port_template - FCD-XXX: qla2xxx: Process responses in Tx path if any available for better performance Changes: Call process_response_queue() in Tx path - FCD-492: Kernel crashes when accessing port_speed sysfs file Changes: CNA: Fix this by changing the lookup. - FCD-XXX: qla2xxx: Refactor asynchronous command initialization - FCD-XXX: qla2xxx: USCM - Add profile support for throttling IO - FCD-XXX: qla2xxx: Move heart beat handling from dpc thread to workqueue - FCD-XXX: USCM: Enhancement to throttle only read traffic during host congestion and write traffic during target congestion. - 10.02.07.00.a1-k1 BH 08/22/2021 - FCD-124: qla2xxx: edif: Use link event to wake up app Changes: The link up event would notify app of the present of a new SCSI Host. - FCD-299: qla2xxx: Fix crash in NVME abort path Changes: Fixed the issue by removing stale access. - FCD-XXX: qla2xxx: Display 16G only as supported speeds for 3830c card. Changes: This card doesn't support lower speeds, hence, update the fdmi and sysfs fields to display 16G only. - FCD-226: qla2xxx: Update details for building kdump initrd in NVMe BFS. Changes: Currently inbox driver doesn't support kdump/kexec kernel, hence user need to update kdump initrd to have OOB driver part of it. - FCD-372: qla2xxx: Anomaly in the congestion stats Changes: Clear the signal counter on a qaucli clear - FCD-279: Request QCC to check/report adapter's MCTP state Changes: qla2xxx: Add support for mailbox passthru - FCD-XXX: Perf improvement: Pick qpair such that Tx and Rx are processed on same CPU. Changes: qla2xxx: Select qpair depending on which CPU post_cmd() gets called - FCD-XXX: scsi: qla2xxx: Reserve extra IRQ vectors - 10.02.06.02-k1 BH 08/11/2021 - FCD-511: Path does not go into "Marginal" state on receiving FPIN-LI Change: qla2xxx: Pass the LI events to the scsi_transport_fc - 10.02.06.01-k1 BH 07/27/2021 - ERXXXXXX: qla2xxx: Check for firmware capability before creating QPair. Change: Move the check for FW attributes to right location. This check is specific for ISP25XX. - 10.02.06.00-k1 BH 07/21/2021 - ERXXXXXX: qla2xxx: Version number is changed from 10.02.06.00.a1-k1 to 10.02.06.00-k1 - 10.02.06.00.a1-k1 BH 06/29/2021 - FCD-297: Fix NVME session down detection Change: qla2xxx: Session tear down and allow relogin to re-drive the connection under condition - ER148553/FCD-156: Fix NVME retry Change: qla2xxx: Alternate back and forth on every PRLI failure until login retry count has depleted or it is succeeded. - FCD-316: System crash when number of CPUs forced to 2 - Change: qla2xxx: Sync queue idx with queue_pair_map idx. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - ERXXXXXX: qla2xxx: Readme: Remove workaround of forcing of INTa mode for kdump kernel. - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - FCD-316: System crash when number of CPUs forced to 2 Changes : qla2xxx: prevents unbalanced QP allocation where nr_hw_queues is two less than the number of CPUs. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - FCD-268: Multiple USCM ELS are sent - FCD-280: Fix issues reported by running a few Jammer tests Changes: qla2xxx: Retry the USCM ELS 3 times when there are failures. - FCD-172: build.sh: Fix udev script installation error - ER148402: Install restrictions when binary rpm is already installed. Changes: qla2xxx: Updated README file for documentation - ERXXXXXX: qla2xxx: Support kdump kernel for NVMe BFS. - ERXXXXXX: qla2xxx: Update README file for building kdump initrd in NVMe BFS. - ER148402: Disallow install if qla2xxx rpm is installed. Changes: qla2xxx: Prevent install from source if rpm is installed. - FCD-230: Add additional debug logs Changes: qla2xxx: Add additional logs to differentiate between FW driver and driver driven ELS -FCD-XXXX: Changes to support kdump kernel. Changes: qla2xxx: Don't allocate fw dump for kexec kernel and Allocate single Q for kexec kernel. - FCD-227: Linux Driver order of RDF to follow EDC ELS - FCD-225 - Qaucli fails to list scm stats for Qlipper - FCD-172: fix udev rule Changes: qla2xxx: permission of the rule file set to 644 - ER148529: NVMe initiator connected to brocade fabric are down Changes: qla2xxx: Fix hang on NVME command timeouts. - ER148531: SN1600Q/SN1610Q, Gen10PlusSnap4 - Async-login failed errors on BFS boot-up-QXCR1001796980 Changes: qla2xxx: Suppress unnecessary log messages during login - ER148578: Observed that initiator is sending prli type 0x8 for for nvme ports Changes: qla2xxx: fix NVME | FCP personality change. - ER148141: Driver vmkmgt: Don't differentiate Signals and FPIN's for the Congestion counters when they detected. Changes: qla2xxx: Split congestion warnings and alarms based on signals and FPINs - ERXXXXXX: Add support for marginal path. Changes: qla2xxx: Added support for eh_should_retry_cmd callback in qla2xxx host template. - ERXXXXXX: scsi: qla2xxx: Flush all sessions on zone disable - ERXXXXXX: scsi: qla2xxx: Fix memory size truncation - ERXXXXXX: scsi: qla2xxx: Fix a NULL pointer dereference in an error path - ERXXXXXX: qla2xxx: fix sparse warning. - ERXXXXXX: qla2xxx: edif: do secure plogi when auth app is present - ERXXXXXX: qla2xxx: Add license. - ERXXXXXX: qla2xxx: USCM - Do not send EDC/RDF ELS when firmware has already sent it - ERXXXXXX: qla2xxx: Inclusion words are applied on release note and readme file - ERXXXXXX: qla2xxx: edif: add N2N support for EDIF - ERXXXXXX: qla2xxx: Updated drelease.notes header - ERXXXXXX: qla2xxx: Fix hang during NVME session tear down. - ERXXXXXX: qla2xxx: USCM: Cleaned up a few debug messages - ERXXXXXX: qla2xxx: edif: fix edif enable flag - ER148546: USCM: QCC Cong Mgmt not available on port with FW:v9.07.00 and DVR:v10.02.05.00.a6-k Changes: qla2xxx: setting the flags to indicate to the application that the RDF is complete and SCM is supported. - ERXXXXXX: Add heartbeat check Changes: qla2xxx: Use 'no-op' mailbox command to check to see if FW is still responsive. - ERXXXXXX: DEBUG: simulate FW hang. Changes: qla2xxx: Driver will detect the hang and recover via hearbeat check. - ERXXXXXX: qla2xxx: Check for FW attributes before enabling MQ. - ERXXXXXX: qla2xxx: USCM Handle ELS errors from switch by retrying 3 times - ERXXXXXX: scsi: qla2xxx: Correct the supported speeds for 16G Mezz card. - ER148472: With NPIV ports, link bounce causes loss of strongSwan session at the target. Changes: qla2xxx: : fix npiv create errorneous error qla2xxx: EDIF: reject AUTH ELS on session down. qla2xxx: edif: Fix stale session - ER148478: System Crash while NPIV RAW IO ON VPORT LUNS on SLES15 SP3 + QLE 2692 + R7525 Changes: qla2xxx: fix unsafe removal from link list. - ERXXXXXX: qla2xxx: USCM - Send EDC and RDF ELS from the driver - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: v2: fix crash in PCIe error handling - ER148123: Issue with Max secure connection with override_lower_limits Changes: qla2xxx: v2: fix stuck session - ER148402: SLES, Driver Install location is inconsistent. Changes: qla2xxx: Fix driver install location for SLES - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Changes: qla2xxx: edif: doorbell tweak - ER148448: Issue w.r.t qaucli, where Remote type "Unknown" for eDIF env. for qaucli2.4.0.build 20 Changes: qla2xxx: fix port type info - ER148433: The log does not show a valid data rate while the link speed is 64G. Changes: qla2xxx: fix debug print of 64G link speed. - ER147650: 'show fdmi? command does not list ? OS Name and Version? parameter for SLES12SP4-QXCR1001771822 Changes: qla2xxx: Show OS name and version in FDMI-1 - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: fix mailbox recovery during PCIE error qla2xxx: v2: fix crash in PCIe error handling - ERXXXXXX: qla2xxx: Changes to support FCP2 Target. - ERXXXXXX: qla2xxx: include AER debug mask to default - ERXXXXXX: qla2xxx: fixes for compilation on RH8.4 - ERXXXXXX: qla2xxx: Do logout even if fabric scan retries got exhausted. - 10.02.05.00.a1-k1 BH 02/27/2021 - EDIF Changes: - ER148247: issue with nvme-npiv env, once we delete npivs, after a while, it is reducing strongswan connections. Change: free sa index during npiv delete - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Change: adjust online|offline notification to app and tweak LOGO on session down. - ERXXXXXX: qla2xxx: edif: tweak log message - ERXXXXXX: qla2xxx: edif: Redundant code (already set in qla_edb_node_alloc) - ER147707: qla2xxx: Device recovery not happening and OS hungs on qla2xxx Change: Fix RISC RESET completion polling. - ER148111: qla2xxx: FCPowerKit reflects huge delays in CMDlets execution. Change: Check lockdown functionality before requesting lockdown feature. - ER148277: USCM: Linux Peer showing misleading 'Congested, throttling down, permitted: 1', prior to 'Reached low watermark, permitted: 2': - Change: Fix misleading debug message - ERXXXXXX: adjust request/respond queue size for 28xx - ERXXXXXX: qla2xxx: Change %p to %px in the log messages. - 10.02.01.00.a15-k1 BH 11/12/2020 ERXXXXXX: qla2xxx: Updated README file for new module parameters - 10.02.01.00.a14-k1 BH 11/06/2020 - ER146725: eDIF another driver panic running script: ./test_target_no_unload.sh Change: qla2xxx: Fix crash in qla_nvme_abort_set_option. - ER147771: Call Trace while shutting down the adapter ports (LINK DOWN). Change: qla2xxx: Handle aborts correctly for port undergoing deletion. - ERXXXXXX: qla2xxx: Add scsi_change_queue_depth to slave configure. - 10.02.01.00.a13-k1 BH 10/28/2020 - ER147600: Cisco: rpd ELS cmd fail to fetch the speed capabilities Change: qla2xxx: Used correct rdp spec, which was broken during code clean-up. - ER147695: FC-NVMe target discovery fails when initator wwpn < target wwpn in an N2N (Direct Attach) config Change: qla2xxx: fix N2N + NVME connect retry fail - ER147832: Issue with uSCM Linux with QCC CLI for some configuration Change: qla2xxx: Show event severity only when device state is congested. - ER147824 : scmr_stat sysfs node runs out of memory Change: qla2xxx: Come up with a compact version of scmr_stat - ER147823: NVMe IO is not getting throttled up or down. Change: qla2xxx: Enable throttle control for NVMe targets for Peer Congestion. - ERXXXXXX: qla2xxx: Count tgt short term link if link comes back before dev_loss_tmo. - ERXXXXXX: qla2xxx: Correct the check for fcport while displaying target counters. - ERXXXXXX: qla2xxx: Change trigger for host short term link down to dev loss tmo. - ERXXXXXX: qla2xxx: Move an SCM log under a debug level. - ERXXXXXX: qla2xxx: Set vendor_rsp[0] value. - ERXXXXXX: qla2xxx: Make throttling messages more informative. - 10.02.01.00.a12-k1 SK 10/15/2020 - ER147625: NVMe IO's are failing with Read/Write after LIP reset. Change: qla2xxx:Return EBUSY until the remote port delete finishes. - ER147653: Target side strongswan start/stop, make initiator crashed. Change: qla2xxx: edif: v2 fix double bsg done. - ER147791: USCM: clear option is not clearing hba alarm/warning, or clear cong or nvme target stats. Change: qla2xxx: Clear Sev and NVMe Target Stats. - ER147793: USCM: Throttling has wrong throttling up info and event period is not honored. Change: qla2xxx: Fix Throttling algorithm regression. - ER147759: NVMe Admin commands are getting throttled and causing admin queue failures. Change: qla2xxx: Throttle NVMe I/O commands only. - ERXXXXXX: qla2xxx: edif: fix aes_gmac mode. - ERXXXXXX: qla2xxx: edif: v2: standardize on port_id_t for bsg api. - ERXXXXXX: qla2xxx: edif: fix 4byte align. - ERXXXXXX: qla2xxx: edif: fix ELS meta data. - ERXXXXXX: qla2xxx: Clear Congestion State/Throttling during chip Reset. - ERXXXXXX: qla2xxx: Clear SCM Severity as part of SCM Stats Clear. - 10.02.00.02.a11-k1 BH 10/09/2020 - ER147734 : Lip reset on the isolated port causes server crash Change: qla2xxx: Don't allow FW, MPI and lip reset on isolated port. - ER147479 - PPC BE RH7.6 - qla2xxx driver loading - machine crashed. Change: qla2xxx: Fixes for big endian machines - ER147646: Call Trace observed while validating a MPI Pause test scenario. Change: qla2xxx: Correct the WARN_ON check in qla_nvme_abort_set_option. - ER147615: Throttling does not work with low I/Os. Change: qla2xxx: Check and round off fractional I/Os to 1 on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: List NVMe targets under scmr_stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Don't check for port isolation during abort isp. - ERXXXXXX: qla2xxx: SCM: Turn off SCM port parameter update mailbox command. - ERXXXXXX: qla2xxx: Fix I/O failures during remote port toggle testing - 10.02.00.02.a10-k1 BH 09/25/2020 SCM Changes: - ERXXXXXX: Changes - qla2xxx: Clear Congestion state when an RSCN is received/target is torn down. qla2xxx: throttling algorithm improvement. qla2xxx: Add throttling support for NVMe targets. EDIF Changes: - ERXXXXX: LUN loss on ipsec stop/start on target side. Change: save Nport on receive of PLOGI - ERXXXXX: fix ELS receive collision between physical and NPIV hosts. Change: remove erroneous source Nport ID search. - ER147570: FCP Performance Drop in latest driver for smaller IOs size. Change: qla2xxx: Change WQ_UNBOUND to WQ_MEM_RECLAIM. WQ_MEM_RECLAIM : wq is guaranteed to have at least one execution context regardless of memory pressure. - ER147632: QLE2774: RHEL 8.2 System crashes while upgrading he FW from 9.6.0 to 9.6.1 with QCC CLI build 12 Change: qla2xxx: Fix system crash on nvme abort path by checking sp of aborting command before accessing it. - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. - ER147645: System panic while trying to capture debugfs stats for EED. Change: qla2xxx: Check rport before accessing target number. - ER147632: Fix potential stale mem access Change: remove stale sp pointer reference - CQXXXXXX: FPIN events are not readily decodable. Change: qla2xxx: Make FPIN events prints human readable. - ER146879: Add support to clear SCM Stats Change: qla2xxx: Added support to clear SCM/SCMR Stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Allow get host stat during reset and sync reset. - ERXXXXXX: qla2xxx: Set reset_cmd_err_cnt on reset failure only. - ERXXXXXX: qla2xxx: Add isolated flag and return EPERM on isolation. - ERXXXXXX: qla2xxx: Count short term link if link comes back in 10 sec. - ERXXXXXX: qla2xxx: Don't check for fw_started while posting nvme command. - ERXXXXXX: qla2xxx: Pass irq_offset to blk_mq_pci_map_queues API. - ERXXXXXX: qla2xxx: lockdown: fix stale sp access. - BZ1868688: qla2xxx: tear down session if FW say its down. - 10.02.00.02.a9-k1 BH 09/03/2020 - ER147554 - sg_reset appears hung iterating over too many Qpairs. Change - qla2xxx: limit interrupt vectors to number of cpu. - ERXXXXX - qla2xxx: klocwork: Fix Bit field 'mpi_-' has one bit and is signed. - ERXXXXX - qla2xxx: Change post del message from debug level to log level. - ERXXXXX - qla2xxx: lockdown: fixup - Change error response as per API test. - ERXXXXX - qla2xxx: Fix map_queue interface to use the correct blk-mq call. - ERXXXXX - Added Structural changes for SCM Phase 2 support. Change : qla2xxx: Update structure definitions for SCM to support backward compatibility. - 10.02.00.02.a8-k1 BH 08/30/2020 - ERXXXXXX - Fix point-to-point (N2N) device discovery issue. Change - qla2xxx: Fix point-to-point (N2N) device discovery issue. - ERXXXXXX - To wait for ABTS response on I/O timeouts for NVMe. Change - qla2xxx: To wait for ABTS response on I/O timeouts for NVMe. - ER147523 - BSG stack trace and SCM display issues. Change - SCM: Functional regression with a6 release. - ER 147413 - edif: Fix issue with DIF enable target discovery. Change - qla2xxx: edif: Fix issue with DIF enable target discovery. - ER147480 clear ASYNC_ACTIVE flag to allow relogin. Change - qla2xxx: fix stuck session. - ERXXXXXX - lockdown: add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support - 10.02.00.02.a7-k1 BH 08/22/2020 - ER147495 - edif changes Change - qla2xxx: edif: fix nvme discovery failure qla2xxx: edif: fix els corruption. - ER147478 - SLES 15sp1 10.02...a6-k compile warning Change - qla2xxx: Compilation changes for sles15sp1 - ERXXXXXX - add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support qla2xxx: lockdown: fix compile problem. do not submit - ERXXXXXX: SCMR changes Change - qla2xxx: SCMR: Correct scmr_outstanding_reqs accounting. qla2xxx: SCM: Changes to separate current_events and current_state. qla2xxx: SCMR: Increase local array size. - ER147298 : USCM "Congestion Warning" counter regression Change - qla2xxx: Correct FPIN Structure Definition (Severity). - 10.02.00.02.a6-k1 BH 08/13/2020 - ERXXXXXX - fix crash on session cleanup + unload. Change - qla2xxx: fix crash on session cleanup + unload. - ER147329 - edif changes Change - qla2xxx: edif: fix compile error. do not submit qla2xxx: edif: fix double free on ELS send failure. qla2xxx: edif: reject els if non secure device. qla2xxx: edif: reject ELS on session down. qla2xxx: edif: redefine purex dest addr to be more consistent. qla2xxx: edif: tweak debug messages. qla2xxx: edif: fix nvme+edif target connect problem. - ER147460 - issue with Diag test on QCC CLI 2.4.0 build 10 with 10.2.00.2-a5 driver Change - qla2xxx: edif: move bsg auth els into separate routine. qla2xxx: edif: Fix error in BSG ELS path that has valid response data. - ER147312 - Add support to report MPI FW state. Change - qla2xxx: Add support to report MPI FW state. qla2xxx: Fix reset of MPI firmware. qla2xxx: Fix MPI reset needed message. - ER147437 - With a5 driver observed warning messages. Change - qla2xxx: Compilation changes for Citrix, rhel and sles. - 10.02.00.02.a5-k1 BH 07/31/2020 - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. Change - qla2xxx: Don't process target debugfs stats if port is isolated. - ERXXXXXX : Add SCM stats to scmr_stats node. Change - qla2xxx: Add SCM stats to scmr_stats node. - ER147419 : Fix crash due to request q pointer extraction failure. Change - qla2xxx: Latency measurement patch. - ERXXXXXX : edif: remove redundant field in port_id_t Change -qla2xxx: edif: remove redundant field in port_id_t - ER147331 - extract bbc from PLOGI template payload. Change -qla2xxx: Fix buffer-buffer credit extraction error - ERXXXXXX : Split qla2x00_configure_local_loop() Change scsi: qla2xxx: Split qla2x00_configure_local_loop() - ERXXXXXX : SCMR - Add I/O flow control. Change - qla2xxx: SCMR - Add I/O flow control. - 10.02.00.02.a4-k1 BH 07/23/2020 - ER147402 - Do not install nvme auto connect script if OS is installing it. Change - qla2xxx: auto-connect scripts are install based on nvme-cli package. - ERXXXXXX - Fixed return status of nvme fcp request. Change - qla2xxx: Set NVME status code for failed NVME FCP request. - ERXXXXXX - Multi-que support for TMF. Change - qla2xxx: Multi-que support for TMF. - ERXXXXXX ? edif changes Change - qla2xxx: edif: simplify reserve/release of sa_index. qla2xxx: edif: tweak debug log. qla2xxx: edif: adjust ELS resp length. qla2xxx: edif: send logo on app stop. qla2xxx: edif: remove prlo in session deletion. qla2xxx: edif: Fix app stop stall. - ER147298 - USCM "Congestion Warning" counter regression w/.65 driver. Change - qla2xxx: Correct fpin_descriptor definition. qla2xxx: Consolidate EDIF & SCM Purex Calls. - ERXXXXXX - Calculate avg. time taken by different components for IO completion. Change - qla2xxx: Latency measurement patch. - 10.02.00.02.a3-k1 BH 07/16/2020 - ER147348 - Observing firmware dump while running qaucli -g post port isolation. Change - qla2xxx: Don't check firmware state in case of chip is down. - ER147338 - SLES: Driver load failed - modprobe: ERROR: module 'qla2xxx' is unsupported. Change - qla2xxx: Add support for loading external modules on SuSE. - ER147361 - System panic after enabling port isolated during TimeOutReset. Change - qla2xxx: Synchronize the update the host counters using lock. - ER147370 - Hardware Error counter not incrementing for MBX command timeout. Change - qla2xxx: Update hardware error count for various error conditions. - ERXXXXXX - The change is to help in debuggging. Change - qla2xxx: Move some messages from debug to normal log level. - ER147346 - Observed a call trace after port isolation. Change - qla2xxx: Fix the call trace for flush workqueue. - ERXXXXXX - For debug purpose. Change - qla2xxx: Add error counters to debugfs node. - 10.02.00.02.a2-k1 AE 07/10/2020 - ERXXXXXX - qla2xxx: Fix TCM compilation issues. Change - Enabled build of tcm_qla2xxx module and fixed compile issues. - ERXXXXXX - qla2xxx: edif : Added back the app_stop wait and avoid if link is down. Change - Added wait during app stop. - ERXXXXXX - qla2xxx: Set BIT_13 for NVMe Async events. Change - Driver changes to skip SLER for Async event command. - ER147323 - qla2xxx: Correct the check for sscanf return value. Change - Driver updated to check version correctly. - ERXXXXXX - qla2xxx: v2: Add EDIF support. Change - Refactoring EDIF code for modularity. - ER147298 - Congestion Warning/Alarm counters fail to increment Change - Update driver to increment the counters for congestion signals. - 10.02.00.02.a1-k1 AE 06/29/2020 - qla2xxx: Enable IOCB throttling by default. - qla2xxx: Implementation to get and manage host, target stats and initiator port. - qla2xxx: Add SLER and PI control support. - qla2xxx: Do not log message when reading port speed via sysfs - qla2xxx: fix null pointer access. - qla2xxx: Use MPI hang trigger to do PEGTUNE halt. - qla2xxx: Reduce erroneous error in link reset path - qla2xxx: v2: fix stalled N2N reconnect. - qla2xxx: Fix warnings on SLES12SP5. - qla2xxx: Fix compilation issues on SLES15 - qla2xxx: Compilation Fixes for SLES15SP1. - qla2xxx: Debugfs compilation issue fix for RH7.6. - qla2xxx: Fix gcc test compile error output being printed. - qla2xxx: Timestamp device online and offline transitions. - qla2xxx: Add rport fields in debugfs. - qla2xxx: Allow dev_loss_tmo setting for FC-NVMe devices. - qla2xxx: Setup debugfs entries for remote ports. - qla2xxx: Fix edif related compilation issue on RH7.6. - Fixes for compilation on hpe branch - qla2xxx: Compilation fixes for RH8.2 - qla2xxx: Compilation changes for RH7.6 - qla2xxx: Fixes for compilation on RH7.x I - qla2xxx: bsg_job to bsg_job_t - qla2xxx: I Unify source code to work with newer kernels. - qla2xxx: Makefile changes from code-uni-devel-10x. - qla2xxx: qla_edif file changes to compile the driver. - qla2xxx: Fix compilation issues. - qla2xxx: Fix Makefile issue. - qla2xxx: fix compile error - qla2xxx: Use explicit LOGO in target mode - qla2xxx: Add EDIF support. - qla2xxx: Addd edif related files. - qla2xxx: Fix MPI failure AEN (8200) handling. - qla2xxx: SCM - Backport optimizations and style changes from upstream work. - qla2xxx: Fix warning in qla_attr.c file. - qla2xxx: Fix nvme compilation error. - qla2xxx: Fix crash in alloc w/GFP_KERNEL + interrupt - Author : Quinn Tran <qutran@marvell.com> qla2xxx: v2: add iocb resource tracking. - qla2xxx: Fix WARN_ON in qla_nvme_register_hba. - qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime. - qla2xxx: Make tgt_port_database available in initiator mode. - qla2xxx: reduce noisy debug message. - qla2xxx: Fix mailbox Ch erroneous error - qla2xxx: fix login timeout. - qla2xxx: Accomodate for SCM FW attribute bit change. - qla2xxx: post FC event (FPIN) to transport FPIN handler. - qla2xxx: Hide fc_host_fpin_rcv kernel dependency. - qla2xxx: Add changes to compile across various kernels. - qla2xxx: Use active targets to update SCM stats. - qla2xxx: Move SCM functions to qla_isr to keep changes local. - qla2xxx: Code to process FLOGI ACC extended payload. - qedf: Fix compilation issue - revisit. - qla2xxx: SCM Phase 1 Implementation + 2 other patches. - qla2xxx: Enable PUREX passthru post ISP reset. - qla2xxx: Fix hang when issuing nvme disconnect-all in NPIV. - qla2xxx: performance tweak - scsi: qla2xxx: fix fcport null pointer access. - fixup! qla2xxx: Fix unbound NVME response length. - scsi: qla2xxx: Fix unbound NVME response length - qla2xxx: Add host attribute to trigger MPI hang. - qla2xxx: ONEOFF: silent dbg messages for good path io. - qla2xxx: ONEOFF: fix pDIF detection - qla2xxx: Snoop inquiry response atleast 168 bytes to determine proprietary DIF. - qla2xxx: ONEOFF: add debug counters for T10-PI/DIF - qla2xxx: ONEOFF: add MQ support for HP3PAR propritary T10-PI - qla2xxx: HPE 3PAR private T10-PI support. - qla2xxx: Check for fabric_priority flag during login - qla2xxx: use iocb_fabric_priority flag - qla2xxx: Fix QoS name and add debug logs - qla2xxx: Correction to tests for iocb fabric and fcport qos. - qla2xxx: Use ->isp_ops->read_optrom() in qla26xx_read_qos_fcport_table(). - qla2xxx: QoS fcport table index initialization improvement. - qla2xxx: Add QoS fcport table index to speed up search. - qla2xxx: Reduce stack on qos fcport priority routines. - qla2xxx: HPE: Register FDMI QOS - qla2xxx: Add bsg interface for qos lun level bitmask. - qla2xxx: Read E2E QoS fcport priority bitmasks from flash. - qla2xxx: Abstract qos lun level mask for iocb cs_ctl field. - qla2xxx: Add fabric priority qos lun iocb mechanism. - qla2xxx: Implement CT command GFO (Get Fabric Object). - qla2xxx: Add support for fabric priority per target. - qla2xxx: fix mtcp dump collection failure. - qla2xxx: Set Nport ID for N2N - qla2xxx: Fix crash during device discovery. - qla2xxx: Handle NVME status iocb correctly. - qla2xxx: Remove restriction of FC T10-PI and NVME - qla2xxx: serialize fc_port alloc in N2N - qla2xxx: NPIV does not come up after FW dump. - qla2xxx: fix RDP respond data format bug. - qla2xxx: force semaphore on flash validation failure. - qla2xxx: add more FW debug information - qla2xxx: Revert: Disable T10-DIF feature with FC-NVMe during probe - qla2xxx: Update BPM enablement semantics. - qla2xxx: fix FW resource print error. - qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs. - qla2xxx: Ensure flash updates return possible failure status through bsg interface. - qla2xxx: Improved secure flash support messages - qla2xxx: fix flag passing error - qla2xxx: Use FC generic update firmware options routine for ISP27xx. - qla2xxx: Avoid setting firmware options twice in 24xx_update_fw_options. - qla2xxX: Add 16.0GT for PCI String - qla2xxx: Use FW_STARTED macro - qla2xxx: Add fixes for mailbox command - qla2xxx: Fix login IOCB flag - qla2xxx: Save rscn_gen for new fcport - qla2xxx: firmware option 3 is clobbered by speed set - qla2xxx: ISP28xx active FW region - qla2xxx: Add portname to print logs in qla24xx_logio_entry(). - qla2xxx: Correction to MB in-direction selection in qla2x00_echo_test(). - qla2xxx: Correction to selection of loopback/echo test. - qla2xxx: Use endian macros to assign static fields in fwdump header. - qla2xxx: Add Speed in SFP print information - qla2xxx: Fix RDP response size - qla2xxx: Handle cases for limiting RDP response payload length. - qla2xxx: Add deferred queue for processing ABTS and RDP. - qla2xxx: Cleanup ELS/PUREX iocb fields. - qla2xxx: Add devid's and conditionals for 28xx. - qla2xxx: Add vendor extended FDMI additions and amendments. - qla2xxx: Provide separate RDP enable. - qla2xxx: Add vendor extended RDP additions and amendments. - qla2xxx: Add changes in preparation for vendor extended FDMI/RDP. - qla2xxx: Add 2061 PCI ID - qla2xxx: Remove all DIX-0 references - qla2xxx: Add endianizer macro calls to fc host stats. - qla2xxx: Add sysfs node for D-Port Diagnostics AEN data. - qla2xxx: Move free of fcport out of interrupt context. - qla2xxx: Add beacon LED config sysfs interface. - qla2xxx: Add sysfs hooks for FC-NVMe autoconnect - 10.01.00.22-k AE 06/29/2020 - Upstream driver as part of Linux 5.6 - Add workaround for 5762 MRRS (Severity:Medium) - Update copyright year to 2017 (Severity:Minor) - Add support for RHEL 7.4 and SLES12SP2 (Severity:Medium) - Add support to notify min/max MTUs through min_mtu & max_mtu (Severity:Medium) - Add support to overide clock for 5762 (Severity:Medium) - Backport upstream patches (Severity:Medium) - Add PHY reset workaround in change MTU path for 5717/19/20 (Severity:Medium) - Update the copyright (Severity:Minor) - Add SLES 15 support (Severity:Medium) - Add RHEL 7.5 support (Severity:Medium) - Fix RHEL 6.4 compilation (Severity:Medium) - Add Ubuntu 18.04 support (Severity:Minor) - Fix race between tg3_get_stats64() and tg3_free_consistent() (Severity:Minor) - Avoid usleep_range() with holding spin lock (Severity:Minor) - Add private ioctl support for register read/write (Severity:Medium) - Add RHEL 8.0 support (Severity:Medium) - Fix Panic with SLES12SP3 (Severity:Minor) - Add workaround for 5762 MRRS (Severity:Medium) - Update copyright year to 2017 (Severity:Minor) - Add support for RHEL 7.4 and SLES12SP2 (Severity:Medium) - Add support to notify min/max MTUs through min_mtu & max_mtu (Severity:Medium) - Add support to overide clock for 5762 (Severity:Medium) - Backport upstream patches (Severity:Medium) - Add PHY reset workaround in change MTU path for 5717/19/20 (Severity:Medium) - Update the copyright (Severity:Minor) - Add SLES 15 support (Severity:Medium) - Add RHEL 7.5 support (Severity:Medium) - Fix RHEL 6.4 compilation (Severity:Medium) - Add Ubuntu 18.04 support (Severity:Minor) - Fix race between tg3_get_stats64() and tg3_free_consistent() (Severity:Minor) - Avoid usleep_range() with holding spin lock (Severity:Minor) - Add private ioctl support for register read/write (Severity:Medium) - Add RHEL 8.0 support (Severity:Medium) - Fix Panic with SLES12SP3 (Severity:Minor) - Release version 25.04-OFED.25.04.0.6.1.1.rhel10u0 - Release version 25.04-OFED.25.04.0.6.1.1.rhel9u5 - Release version 25.04-OFED.25.04.0.6.1.1.rhel9u6 - Release version 25.04-OFED.25.04.0.6.1.1.sles15sp6 - Release version 25.04-OFED.25.04.0.6.1.1.sles15sp7 - Added nfsrdma support - Added ibdev2netdev script - Support install macro that removes RPM_BUILD_ROOT - Add mlx4_fc and mlx4_vnic support - Add KMP support - Add weak updates support - Remove FC support - Use one spec for KMP and non-KMP OS's. - Add QoS utils. - Renamed kernel-ib package to mlnx-ofa_kernel-modules - Added nfsrdma support - Added ibdev2netdev script - Support install macro that removes RPM_BUILD_ROOT - Add mlx4_fc and mlx4_vnic support - Add KMP support - Add weak updates support - Remove FC support - Use one spec for KMP and non-KMP OS's. - Add QoS utils. - Renamed kernel-ib package to mlnx-ofa_kernel-modules - 10.02.14.00-k1 AG 05/21/2025 - - 10.02.14.00.a4-k1 AG 02/27/2025 [FCD-4186] : Device discovery fails on continuous reboot (Hitachi) Resolution : In a fabric topo when there is mismatch in state of login between driver and FW, query FW again and proceed with login Scope : 27xx/28xx Adapters [FCD-XXX] : Make functions local to a file static Resolution : Make functions local to a file static Scope : 27xx, 28xx series Adapters [FCD-XXX] : Remove unused function Resolution : Function qla25xx_set_purex is unused - remove it Scope : All adapters [FCD-4729] : Compilation errors with Sles15sp6 Resolution : Fix compilation errors on Sles15 SP6 Scope : Series Adapters [FCD-4536] : Compilation errors on RHEL10 Resolution : RHEL 10 has rebased to the latest kernel resulting in several build issues. Fix them and ensure that it builds on older kernels as well. Scope : Series Adapters [FCD-4676] : Add support for RH 9.6 (compilation) Resolution : Fix compilation errors on RH 9.6 Scope : Series Adapters [FCD-XXX] : Update README to reflect the supported distros Resolution : Update README to reflect the supported distros Scope : All Adapters Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com> Change-Id: Ic4af035fd48a3137923c7d3590be4271b0a7fd32 commit e22ea0921e20bcf93db0fae2b8dd579005686908 Author: Anil Gurumurthy <agurumurthy@marvell.com> Date: Fri Jan 10 11:06:14 2025 +0530 qla2xxx: Update driver version to 10.02.13.03-k1. - 10.02.13.03-k1 AG 01/10/2025 [FCD-4627] : HPSD5.10-BFS RHEL9.5 system crash on Nimble-HF40 failover test. Resolution : Check for sp being valid, before freeing associated memory Scope : All - 10.02.13.02-k1 MR 01/07/2025 [FCD-4657] : Fix SCSI INQ issue for supporting T10 DIF. Resolution : Replace sp completion with qpair completion call.. Scope : 28XX - 10.02.13.01-k1 MR 01/02/2025 [FCD-1040] : Call scsi done and nvme done with good completion without lock. Resolution : Done changes to move scsi done and nvme done without lock. Scope : 27xx and above - 10.02.13.00-k1 AG 10/22/2024 - - 10.02.13.00.a3-k1 SD 10/09/2024 [FCD-XXX] : Crash seen during load/unload test in a loop Resolution : Delay module unload when there is a fabric scan going on Scope : All adapters [FCD-4193] : SCSI device never recovers after RSCN Resolution : Remove tape specific checks which prevented recovery Scope : All adapters - 10.02.12.01-k1 MR 05/29/2024 [FCD-3465] : Server got crashed while running port toggle test. Resolution : During vport_delete send async_logout explicitly. Scope : 28XX - 10.02.12.00-k1 SD 05/20/2024 - - 10.02.12.00.a5-k1 SD 05/07/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a4-k1 SD 04/25/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a3-k1 SD 03/15/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : SFP cache on legacy adapter Scope : all - 10.02.12.00.a2-k1 SK 02/08/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : Fix NVME + NPIV connect issue Resolution : Initialize irq offset Scope : ALL - 10.02.12.00.a1-k1 QT 01/09/2024 scsi: qla2xxx: Drop redundant pci_enable_pcie_error_reporting() Resolution : Fix RHEL 9.4 compile issue Scope : ALL [FCD-3515] : API support for SFP data cache Scope : 27xx, 28xx [FCD-xxx] : Fix SLES15.6 compile issue Resolution : Remove stale fields Scope : ALL [FCD-3634] : Remove check req_sg_cnt should be equal to rsp_sg_cnt. Resolution : Firmware supports multiple sg_cnt for request and response for CT commands, so remove the redundant check. Scope : All Adapters [FCD-717] : Move FCE Trace buffer allocation to user control Resolution : Modify existing DFS knob to allow user to enable|disable this feature. Scope : Any [FCD-xxx] : Remove del_work work from qla_schedule_sess_for_deletion. Resolution : Remove del_work work from qla_schedule_sess_for_deletion. Scope : All [FCD-xxx] : Additional target mode code cleanup. Resolution : Additional target mode code cleanup. Scope : All [FCD-xxx] : Update copyright information. Resolution : Update copyright information. Scope : All [FCD-xxx] : Remove target code from qla_target files. Resolution : Remove target code from qla_target files. Scope : All [FCD-xxx] : Remove target mode code from initiator specific files. Resolution : Remove target mode code from initiator specific files. Scope : All [FCD-xxx] : Move common code to initiator specific files. Resolution : Move common code to initiator specific files. Scope : All [FCD-3751] : Fix use after free on unload Resolution : Remove duplicate signals on freeing dpc_thread Scope : ALL [FCD-3515] : Caching SFP data Scope : 27xx, 28xx [FCD-xxx] : Exec FW with delay Resolution : Add delay before command retry Scope : 28xx [FCD-xxx] : fix abort in bsg timeout Resolution : Wait for bsg to return before abort exit Scope : ALL [FCD-xxx] : Use QP lock to search for bsg. Resolution : use correct lock to protect search Scope : ALL [FCD-xxx] : Remove SQ in queuecommand Resolution : Remove duplicate code. Scope : ALL [FCD-xxx] : Reduce fabric scan duplicate code. Resolution : Consolidate routines that handle GPNFT & GNNFT. Scope : ALL [FCP-743] : Remove ql2xstay_attach_on_load_failure Resolution : Remove driver parameter used as part of feature test. Scope : 27xx, 28xx - 10.02.11.00-k1 NJ 10/25/2023 [FCD-xxx] : Remove PCI ID 0x2971 Resolution : Remove PCI ID 0x2971 Scope : [FCD-3661] : Remove 8031 from deprecate and unmaintained list. Resolution : Remove 8031 from deprecate and unmaintained list. Scope : 8031 [FCD-3571] : Unable to resume FW dump collection Resolution : send notification to udev Scope : 27xx, 28xx [FCD-3631] : Convert Port disable state to maintenance mode Resolution : Rename state and turn flag indicator Scope : 27xx + 28xx - 10.02.11.00.a8-k1 NJ 10/13/2023 [FCD-3632] : Remove support for FCoE device ids. Resolution : Remove FCoE ids from pci table. Scope : 8xxx [FCD-3624] : Fix optrom version displayed in FDMI Resolution : Populate EFI version Scope : Series Adapters [FCD-3632] : Remove CNA reference from README. Resolution : Remove CNA reference from README. Scope : 8xxx - 10.02.11.00.a7-k1 NJ 09/22/2023 [FCD-3195] : Fix flash read failure Resolution : Check return code for each flash read. Scope : Series Adapters [FCD-3571] : System flood by fw dumps Resolution : udev script to pause fw dump collection Scope : Any [FCD-3566] : Limit FW dump improvement to 27xx + 28xx Resolution : Add filter for 27xx + 28xx adapters Scope : 27xx+ [FCD-3497] : Return ENOBUFS if sg_cnt is more than one for ELS cmds. Resolution : This error is because FW support single sg element for ELS Pass-through IOCB (0x53h). This particular error code will help API and Apps to display appropriate message to the user. Scope : All Adapters [FCD-3510] : RHEL & SLES OOB driver request: deprecate L8/Hilda HW Resolution : Added a frame work to display the message based on device and OS. Scope : L8 and L16 (Hilda and CNA) [FCD-3269] : Init Control Block is dereferenced incorrectly Resolution : Correctly dereference ICB Scope : 20xx [FCD-3421] : Add Support to collect fw_dump on system crash or panic. Resolution : Add Support to collect fw_dump on system crash or panic Scope : 27xx, 28xx - 10.02.11.00.a6-k1 MR 09/08/2023 [FCD-XXX] : Modify error code handling for sfp fw upgrade mbx. Resolution : Modify error code handling for sfp fw upgrade mbx. Scope : 28xx [FCD-XXX] : Block sysfs resets and fw_dump during sfp fw upgrade Resolution : Block sysfs resets and fw_dump during sfp fw upgrade Scope : 28xx [FCP-743] : Block sysfs access during maintenance mode Resolution : Add check for maintenance mode. Scope : Any [FCD-3506] : Fix double free of dsd_list during driver load. Resolution : add pointer check before access Scope : Any - 10.02.11.00.a5-k1 MR 08/18/2023 [RH BZ 2039422] : NVMe-FC kernel crash during reload driver test Resolution : validate nvme_local_port correctly Scope : Any [FCD-XXX] : Fix for potential Null pointer dereferenced Resolution : Check before dereferencing pointer Scope : Any [FCP-743] : Enable driver attach to bad HW Resolution : turn on ql2xstay_attach_on_load_failure option Scope : 27xx, 28xx - 10.02.11.00.a4-k1 MR 08/11/2023 [FCD-xxx] : Update README file for zio information Resolution : Update readme file with zio information Scope : Any [FCD-3415] : Std-DIF is not working with HPe K1 driver Resolution : Reset the protect bit in the INQ response only when pDIF is enabled and negotiated. Scope : 26xx/27xx/28xx - 10.02.11.00.a3-k1 AG 08/03/2023 [FCP-743] : Allow only selective BSG requests in maintenance mode Resolution : Allow certain BSG to go through during maintenance mode Scope : Any [FCP-743] : FW dump improvement Resolution : Improve data capture Scope : 27XX, 28XX [FCD-3252] : Unable to act on RSCN for port online. Resolution : Clear RSCN flag only when driver is acting on the notification Scope : Any [FCD-xxx] : 32 Bytes CDB Resolution : Use Type 6 IOCB for CDB bigger than 16Bytes Scope : Any Unit Test : i) force IO to use Type6 only for over the weekend run. ii) force error path(s) to make sure no crash. [FCD-xxx] : Move resource to allow code reuse. Resolution : relocate dsd_list to qpair Scope : Any - 10.02.11.00.a2-k1 AG 07/27/2023 [FCD-3411] : CS_DMA Error observed while running DIF IO Resolution : While running DIF enabled IO, a CS_DMA error was observed. A FW dump is needed to better debug this. So take a FW dump on encountering this. Scope : 27xx/288 series of adapters [FCD-3406] : Modifiy default zio threshold value. Resolution : Modifiy default zio threshold value. Scope : 27xx/28xx Series Adapters [FCD-3314] : Delay IO Abort on PCI error Resolution : On detection of PCI error, allow IO's to wind down. Scope : Any [FCD-3314] : Fix system crash due to bad pointer access Resolution : Check SRB type before access. Scope : 27xx+ - 10.02.11.00.a1-k1 AG 07/14/2023 - FCP-749: qla2xxx: Add support for build for RH 9.3 and RH 8.9 distro Resolution : Build on RH 9.3 was failing owing to change of definition of fc_host_fpin_rcv and removal of DID_TARGET_FAILURE. Fix part of it by updating to latest upstream code. Scope : 27xx/28xx series of adapters - FCD-3302 : During unload Error detected messages is seen. Resolution : Change the wording of the message as its not an error. Scope : Series Adapters - FCD-3293 : Initiator sever getting crashed after LOGO. Resolution : Fix double free of fcport Scope : Any - Revert "scsi: qla2xxx: Change default ZIO threshold." This reverts commit 8812bcc1b7a25494ec8755ff3b61412a9993ff5b. The ZIO threshold now is 64. - FCD-xxx : Fix unreachable code Resolution : Remove dead code Scope : 28xx+ - FCD-3232 : Potential risk of double free pointer detected in Coverity scan by ran by Citrix Resolution : NULL the pointer after first free. Scope : All - 10.02.10.00-k1 SK 06/14/2023 Non-alpha build - 10.02.10.00.a2-k1 BH 05/12/2023 - FCD-3140: qla2xxx: Fix command flush on cable pull. Changes: Add wait for commands to return. - FCD-XXX: qla2xxx: NVME|FCP prefer flag not being honored. Changes: Reread prefer flag on chip reset - FCD-XXX: qla2xxx: Update readme file - 10.02.10.00.a1-k1 BH 05/02/2023 - FCD-XXX: qla2xxx: Update Copyright Changes: Update Copyright for Marvell. - FCD-XXX: qla2xxx: Update manufacturer detail Changes: Update manufacturer detail to "Marvell" - FCD-3140: qla2xxx: Host crash during StressAndHostPortReset test Changes: Remove unused nvme_ls_waitq wait queue. - FCD-XXX: qla2xxx: [RH-BZ 2167274]: Wait for io return on terminate rport. Changes: dd wait to terminate_rport_io - 10.02.09.00.a11-k1 BH 03/27/2023 - FCD-XXX: qla2xxx: Add link down + logo rx stat counts Changes: Add counters to track link down and Logo receive. - 10.02.09.00.a10-k1 BH 03/17/2023 - FCD-XXX: qla2xxx: Support for update SFP firmware of ACCELINK Changes: [New Feature] Support for update SFP FW of ACCELINK WTD 64G - FCD-717: qla2xxx: Split FCE|EFT trace control Changes: Split buffer alloc and enable of feature into individual step. - BZ-2093878: qla2xxx: perform lockless command completion in abort path Changes: Perform lockless command completion in abort path - 10.02.09.00.a9-k1 BH 03/06/2023 - FCD-2390: qla2xxx: Fix N2N stuck connection. Changes: Clear the blocking flag. - FCD-2496: qla2xxx: Prevent command send on chip reset Changes: Check for chip reset before sending IOCB. - FCD-2035: qla2xxx: Fix mem access after free. Changes: Remove access of memory - FCD-2720: qla2xxx: Move cmd_to_req_q latency counter before processing response. - FCD-XXX: qla2xxx: Update readme file for current program - 10.02.09.00.a8-k1 BH 02/27/2023 - FCD-2585: qla2xxx: Remove unsupported ql2xenabledif option. Changes: Removed unsupported ql2xenabledif=1 option and validate the user input. - FCD-2305: qla2xxx: Error code did not return to upper layer Changes: Preserve error code from TMF and return it to upper layer. - FCD-2035: qla2xxx: fix inconsistent TMF timeout. Changes: Allow TMF error to return to upper layer without session tear down. - FCD-2035: qla2xxx: Fix TMF leak through. Changes: Check for chip reset or session change before sending Task management. - 10.02.09.00.a7-k1 BH 02/17/2023 - FCD-2858: qla2xxx: USCM: Check for vp_idx before setting EDC and RDF set flags. Changes: Add check for vp_idx before setting EDC and RDF set flags when processing RIDA. Revert patch: - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition. - 10.02.09.00.a6-k1 BH 02/13/2023 - FCD-2750: qla2xxx: IO's are failing on Standard DIF enabled 3PAR LUN Changes: Revert an offending patch and work on an issue with upstream. - 10.02.09.00.a5-k1 BH 02/06/2023 - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition Changes: Remove EDC and RDF set flags on Report ID Acquisition. - FCD-2879: qla2xxx: Compilation errors on SLES15SP5 Beta3-202301 Changes: Write generic code to find tag of scsi cmnd - FCD-2846: qla2xxx: Correct bsg_reply size in bsg interface Changes: Fix the bsg_job->reply_len with size of "struct fc_bsg_reply" - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the invariant expression in the condition - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the expression flogi_acc_pld_remaining == 0 - FCD-XXXX: qla2xxx: Changes of logs level for SFP temperature monitoring - 10.02.09.00.a4-k1 BH 01/29/2023 - FCD-2308: qla2xxx: Add bsg call to read port information Changes: Add bsg interface to allow app to read remote port information. - FCD-XXX: qla2xxx: KW-97439: unreachable code Changes: Return void if return value is not needed - FCD-XXX: qla2xxx: Add logs for SFP temperature monitoring Changes: Add debug log for Temperature Alert (8070h) Asynchronous Event - 10.02.09.00.a3-k1 BH 01/19/2023 - FCD-XXX: qla2xxx: Add support of RHEL9.2 - FCD-XXX: qla2xxx: Add support of RHEL8.8 - FCD-XXX: qla2xxx: Add support of SLES15 SP5 - FCD-2800: qla2xxx: Add support of OpenEuler-22.03 - 10.02.09.00.a2-k1 BH 01/10/2023 - FCD-XXX: qla2xxx: kw: unreachable code, SRB type is 0 just before latency counter incremented. Changes: SRB type is 0 just before latency counter incremented. - FCD-XXX: qla2xxx: kw: reset current_topology much later Changes: Reset current_topology much later on detecting - FCD-XXX: qla2xxx: kw: unreachable code, CS_COMPLETE is 0 and its already checked. Changes: Remove unreachable - FCD-XXX: qla2xxx: kw: Checking for port_state always yields zero Changes: Instead of bitwise AND check for port_state directly - FCD-1569: qla2xxx: Fix fw resource tracking Changes: Use global counter - FCD-XXX: qla2xxx: [ER-144639]: Flush mailbox commands on chip reset Changes: Use lock to prevent race condition. - FCD-2735: qla2xxx: USCM-VL: NVRAM VL disabled logins with extend FLOGI (VL enabled) Changes: Reset the spl. features control block flag to avoid logging in with ER_RDY. - FCD-XXX: qla2xxx: klockwork: Fix buffer over flow Changes: Use correct buffer size. - FCD-XXX: qla2xxx: EDIF: kw: remove unnecessary bit field - FCD-2563: qla2xxx: Turn off noisy message log. - FCD-XXX: qla2xxx: kw: remove dead code in qla24xx_config_rings - 10.02.09.00.a1-k1 BH 01/10/2023 - FCD-717: qla2xxx: allow FW dump extraction if load fail Changes: Add knob to force driver to stay attached to the fail adapter. - FCD-717: qla2xxx: Initialize FW buffer size with seed value Changes: Initialize FW Buffer size with seed value - FCD-XXX: qla2xxx: klockwork: Remove QLA_COMMAND_ERROR check in qla2x00_execute_fw. Changes: Remove the unnecessary QLA_COMMAND_ERROR check - FCD-2390: qla2xxx: Fix session hang in gnl Changes: Clear this flag to prevent blockage. - FCD-2390: qla2xxx: Fix erroneous link up failure Changes: Set fw_started flag early to prevent interrupts being dropped - FCD-2496: qla2xxx: Fix command flush during TMF Changes: Wait for commands flush before closing TMF - FCD-2035: qla2xxx: Limit TMF to 8 per function Changes: Limit TMF to 8 per function - FCD-XXX: qla2xxx: Add NVMe Disconnect support. Changes: Add support for NVMe Disconnect feature. - FCD-XXX: qla2xxx: Modify qla27xx_copy_fpin_pkt to support PURLS IOCB. Changes: Modified qla27xx_copy_fpin_pkt to support both PUREX and PURLS IOCBs. - FCD-717: qla2xxx: Adjust iocb resource on qpair create Changes: Add call to readjust iocb + exchange limit. - FCD-2390: qla2xxx: Fix deletion race condition Changes: Move check field behind lock - FCD-XXX: qla2xxx: klockwork: Pointer checked for NULL at linx x will be dereferenced at linx x+y. Changes: Remove the unnecessary Null check. The pointer will likely be valid. - FCD-XXX: qla2xxx: Observed call trace in smp_processor_id() with debug kernel Changes: Use raw_smp_processor_id API - FCD-2275: qla2xxx: USCM: Cleanup code related to IOPS based throttling Changes: IOPS and BW based throttling is not used. Remove those code. - FCD-2273: qla2xxx: USCM: Code cleanup w.r.t module params (ql2x_scmr_flow_ctl_tgt, ql2x_scmr_flow_ctl_host) Changes: Remove the redundant module parameters - FCD-2408: qla2xxx: USCM: Driver doesn't honor the adapter port Restore Default Settings Changes: Update the nvram values to the host as well as fcport - FCD-2363: qla2xxx: USCM: Slow Queue usage changes Changes: Use Slow queue only under specific scenarios - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Don't increment the counter for under-run. - FCD-2291: qla2xxx: Erroneous link down. Changes: Allow adapter reset to complete before discovery - FCD-2035: qla2xxx: Fix hang in task management Changes: Bail out of TMF on error - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path - FCD-XXX: qla2xxx: USCM: Debug log message improvement Changes: Log target WWPN for peer congestion - FCD-2164: qla2xxx: Fix stall session after app start Changes: Use session delete to avoid the accidental clearing of scan_flag - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Check fcport state before invoking the mailbox - FCD-XXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: Set throughput baseline on 1st FPIN - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix parsing the fpin when multiple descriptors are present - FCD-XXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCD-XXX: qla2xxx: USCM: Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: Fix for KW-97392 Changes :Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: Remove dead code - flagged by klocwork - FCD-847: qla2xxx: fixup: Fix exchange over subscription. - FCD-2434: qla2xxx: Fix crash when IO abort times out - FCD-XXX: qla2xxx: Rearrange scm rx path handling code. - 10.02.08.01-k1 BH 09/28/2022 - FCD-2392: Fix initrd image creation failure in OpenEuler, Kylin and UOS Changes: Add support for creating initrd image on openEuler, Kylin and UOS - 10.02.08.00-k1 BH 09/16/2022 - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Residual under-run is not an interface error, hence no need to increment that count. - FCD-2291: qla2xxx: Fix erroneous link down. Changes: Allow adapter reset to complete before any scan can start. - FCD-2035: qla2xxx: Fix hang in task management Changes: Add additional error check at various point - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced. - 10.02.08.00.a7-k1 BH 08/22/2022 - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path. - FCD-2164: qla2xxx: USCM: Fix stall session after app start Changes: Prevent accidental clearing of flag that blocks re-login - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset. - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Heck fcport state before invoking mailbox - FCDXXX: qla2xxx: USCM: Debug log message improvement - 10.02.08.00.a6-k1 BH 08/09/2022 - FCDXXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: if VL switchreduces the throughput below 50%, we would not throttle any further. - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix the FPIN parsing to take into account multiple descriptors. - FCDXXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCDXXX: qla2xxx: USCM:Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..10 - 10.02.08.00.a5-k1 BH 07/29/2022 - FCD-XXX: qla2xxx: klocwork: Possible Null Pointer Dereference Changes: Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: USCM: Fix mqueuecommand return code during throttle down request. - FCD-XXX: qla2xxx: Revert klockwork: Fix buffer overrun - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h - FCD-2035: qla2xxx: Fix Task Mgmt Cmd fail due to unavailable resource Changes: Limit TM commands to 8 per target. - 10.02.08.00.a4-k1 BH 07/23/2022 - FCD-847: qla2xxx: Fix exchange over subscription. Changes: check for exchange availability before command submission - FCD-XXX: qla2xxx: Remove unintended flag clearing Changes: Remove unintended flag clearing. - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h Changes: Add wait for completion of Marker! - FCD-XXX: Fix performance dip due to lock contention Changes: Save the allocated memory for reuse and avoid the lock - FCDXXX: qla2xxx: USCM: Do not send EDC and RDF for NPIV ports Changes: Disable sending USCM ELS for vports - FCDXXX: qla2xxx: USCM: VL: Do not set target speed to 1G for slow lane Changes: Do not set the target speed while changing lanes. - FCD-2012: qla2xxx: Throttling up messages seen when profile is changed Changes: Set the new profile for each fcport (along with the host). - FCD-XXX: qla2xxx: USCM: VL - Clean up FLOGI_ACC parsing Changes: structure that could be used to parse the FLOGI_ACC by using offsets - FCD-1990: qla2xxx: Fix nvram load config error Changes: Remove re-definition of port flags while enabling virtual lane support - FCD-XXX: qla2xxx: USCM:VL, I/O does not move back to the normal lane Changes: Check if I/O throttling is being done, before deciding to move the normal lane. - FCD-XXX: qla2xxx: Fix stall login Changes: Reset session state to allow relogin logic to re-drive the connection. - FCD-847: qla2xxx: Fix exchange over subscription for mgt cmd. Changes: would check for exchange availability before command submission. - FCD-847: qla2xxx: Fix exchange over subscription. Changes: would check for exchange availability before command submission. - FCD-XXX: qla2xxx: relocate/rename vp map. - FCD-XXX: qla2xxx: Klocwork: Fix for Unexpected type of a scan function parameter - 10.02.08.00.a3-k1 BH 07/01/2022 - FCD-1818: qla2xxx: Fix call trace in debug kernel due to missing spinlock init Changes: Fix the call trace by initializing trace lock. - FCD-1923: qla2xxx: USCM: VL - After disabling VL via CLI, status shows "Non-operational" Changes: Return VL status appropropriately - FCD-1922: qla2xxx: Fix discovery issues in FC-AL topology Changes: Checks FC loop map when Get ID list returns no device - FCD-1831: qla2xxx: Fix link failure in NIPV environment. Changes: Remove NPIV host from directly being able to chip reset. - FCD-XXX: qla2xxx: Fix DMA-API call trace on NVME LS requests with debug kernel Changes: Remove DMA mapping from the driver - FCD-XXX: qla2xxx: Fix KASAN use-after-free warning in qla24xx_sp_unmap Changes: Remove stale fcport access in qla2x00_rel_sp - FCD-XXX: qla2xxx: Fix KASAN out-of-bounds warning in qla_update_sp Changes: Size for memcpy was corrected to use the right length. - FCD-XXX: qla2xxx: Fix imbalance vha->vref_count Chnages: Add an extra ref count for the task management paths. - FCD-XXX: qla2xxx: Tweak Latency measurement Changes: Move the time read further ahead to the start of queuecommand and later to the point where it is just before scsi_done. - FCD-XXX: qla2xxx: klockwork: Silent superfluous warning. Changes: Remove superfluous Null check. - FCD-XXX: qla2xxx: klockwork: Fix buffer overrun Changes: Replace structure name to allow proper size calculation - FCD-XXX: qla2xxx: Remove dead code (GNN ID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code (GPNID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code. Changes: Removing drport field and FCPORT_UPDATE_NEEDED, and EDIF_TICK_NEEDED signals - FCD-XXX: qla2xxx: Do not select slow queue if USCM is enabled Changes: Do not select slow queue whilie initializing cpu map - FCD-XXX: Select HW queue depending on Tx CPU Changes: Select qpair which is in correlation with Tx CPU - FCD-XXX: qla2xxx: Add support for displaying I/O throttle information Changes: Display the driver I/O throttle information along with VL information - FCD-XXX: qla2xxx: USCM: Throttle only R/W commands for NVME Changes: Throttle only read/write IOs. - Bring back following reverted changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.08.00.a2-k1 BH 06/19/2022 - FCD-XXX: qla2xxx: klockwork - Check valid rport returned by fc_bsg_to_rport Changes: Check valid rport returned by fc_bsg_to_rport - FCD-XXX: qla2xxx: klockwork - Check for a valid fcport pointer Changes: Add a check for a valid fcport pointer at the time of exit - FCD-XXX: qla2xxx: klockwork - Move fcport NULL check to avoid dereference Changes: Move the fcport NULL check to avoid the dereference. - FCD-1883: qla2xxx: USCM: Adapter shows "RDF Complete" when Link is down Changes: Reset the flag, so that when USCM is negotiated, the CLI shows the correct status - FCD-1846: qla2xxx: USCM: A log message while clearing stats Changes: Add a log message while clearing USCM stats - FCD-XXX: qla2xxx: USCM: VL-Reset FC device virtual lane priority to normal on a port flap Changes: Reset the virtual lane to normal on a port flap, ISP reset - FCD-XXX: qla2xxx: USCM: VL-Set target congestion before switching lanes Changes: Set the target state before the lane switch. - FCD-1752: qla2xxx: USCM: VL-Sysfs does not show Virtual Lane as enabled Changes: extended flogi_acc can also be parsed correctly. - FCD-1652: qla2xxx: Check if port is online before sending ELS Changes: Check if port is online before sending ELS - FCD-XXX: scsi: qla2xxx: Synchronize rport dev_loss_tmo setting - 10.02.08.00.a1-k1 BH 05/27/2022 - FCD-XXX: qla2xxx: USCM: Virtual Lane, Fix PUN handling Changes: Have a default priority range for each lane and ensure that the range is programmed correctly - FCD-XXX: qla2xxx: USCM: Support for Virtual Lanes Changes: Enable Virtual Lane support for Cisco switch - 10.02.07.00-k1 BH 05/27/2022 - Non-alpha build - 10.02.07.00.a19-k1 BH 05/21/2022 - FCD-XXX : qla2xxx: USCM: Throttling is not honored for NVMe Changes: Enable NVMe READ/WRITE commands to be throttled - FCD-XXX: qla2xxx: USCM: Add counters to track directional throttling Changes: Add sysfs counters to have stats displayed for busy status returns. - FCD-1801: qla2xxx: USCM: CP reads go to zero while doing directional throttling Changes: Take into account the directional queue depth while returning a busy status to the stack. - FCD-1809: qla2xxx: USCM: Restoring USCM Profile to default result in driver - FCD-1798: qla2xxx: USCM: Profiles are not honored for peer congestion Chnages: Apply the profile to each target (fcport) when the profile is changed. Reverting the following changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.07.00.a18-k1 BH 05/12/2022 - FCD-1484: qla2xxx: Manufacturer details should be "Marvell Semiconductor, Inc." Changes: Update Manufacturer details to indicate Marvell Semiconductors - FCD-XXX: qla2xxx: USCM: Throttle only read and write commands Changes: Throttle only read and write commands. - FCD-XXX: qla2xxx: USCM: Do not clear throttle for Clear Cong FPIN. Changes: Do not clear throttle when Clear Congestion FPIN is received. - FCD-XXX: qla2xxx: USCM: Change default profile to Monitor Changes: Set the default throttle profile as Monitor. - FCD-XXX: qla2xxx: Fix few issues reported by klocwork tool - 10.02.07.00.a17-k1 BH 05/06/2022 - FCD-1522: qla2xxx: USCM: Throughput drops to zero in Monitor mode Changes: Restore qdepth based on monitor mode - FCD-1315: qla2xxx: Fix erroneous mailbox timeout after pci error inject. Changes: Clear wait for MB interrupt flag to prevent stale MB completion arriving - FCD-1424: Remove verbose IO debug messages Changes: Remove the IOCB debug messages for every IO - FCD-XXX: Support for NVMe parameters in Auxiliary Image Status Changes: Added new structure member, bit define and image status check. - 10.02.07.00.a16-k1 BH 04/08/2022 - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - FCD-1221: qla2xxx: USCM: Switch does not send FPINs after a EDC re-negotiation Changes: Send Link Service Request Information wih the EDC response, along with the other descriptors. - 10.02.07.00.a15-k1 BH 03/25/2022 - FCD-1249: qla2xxx: edif: Fix dropped IKE message. Changes: Fixes IKE message being dropped due to error in processing Purex IOCB and Continuation IOCBs. - FCD-1457: qla2xxx: Zero undefined mailbox IN registers Changes: Set zero to unuse register's value while requesting a new MB command. - FCD-1425: qla2xxx: USCM: Seconds since last event showing incorrect value Changes: Calculate delta time correctly - FCD-1287: qla2xxx: Fix incorrect display of max frame size. Changes: Save off the field of interest into separate location and convert into words. - FCD-XXX: qla2xxx: Fix memory leak when reading tgt_port_database debugfs file - FCD-XXX: qla2xxx: USCM: Do not reset SCM stats on a link bounce/ISP reset - 10.02.07.00.a14-k1 BH 03/14/2022 - FCD-XXX: qla2xxx: Fix losing FCP-2 targets on long port disable with IOs Changes: Fix this by accepting RSCN when the device is not online. - FCD-XXX: qla2xxx: Fix losing target when it reappears during delete Changes: Fix the issue by adding state checks before proceeding. - FCD-XXX: qla2xxx: Fix losing FCP-2 targets during port perturbation tests Changes: Fix was to ignore delete for FCP-2 devices in certain sequence. - FCD-119: qla2xxx: Fix crash due to stale srb access around IO timeouts Changes: Ensure srb is either returned during error IO timeout error escalation. If that is not possible fail the escalation path. - FCD-1132: qla2xxx: HPE3PAR: Fix IOCB resource count leak Changes: Decrement FW IOCB resource count. - FCD-1132: qla2xxx: Turn off MQ for 8G adapter. Changes: For 8G adapter, multi queue was enabled accidentally. - FCD-1385: Wind down adapter after pcie error. Changes: Detect the PCIE error and returns all IO's to upper layers. - FCD-1412: qla2xxx: Reset Congestion Warning/Alarm signals count. Changes: Reset signals at every signal check boundary (1 sec). - 10.02.07.00.a13-k1 BH 02/17/2022 - FCD-1353: qla2xx: a12/a11 driver compilation gives warning messages Changes: Fix the fall through warning - FCD-1342: qla2xxx: SL12SP5 a12 driver compilation issue observed Changes: fallthrough macro is defined based on gcc version. - 10.02.07.00.a12-k1 BH 02/09/2022 - FCD-XXX: qla2xxx: Reset USCM stats/state and throttling on RSCN Changes: Reset USCM stats on getting an RSCN indicating a target port down. - FCD-XXX: qla2xxx: Increase max limit of ql2xnvme_queues Changes: Increase max limit of ql2xnvme_queues to (max_qpair-1) - FCD-478: qla2xxx: Fix missing devices on a LOGO from F-Port Changes: A call to logo all ports is made upon a F-Port LOGO. - FCD-XXX: qla2xxx: Move NVMe traffic to the slow queue on target congestion Changes: Steer the NVMe traffic to the slow Q on encountering target congestion - FCD-348: qla2xxx: edif: Fix slow session tear down. Changes: As a work around, driver would trigger a session tear down where it tell the local authentication application to also tear down. - FCD-XXX: qla2xxx: edif: Tweak debug log. Changes: Print AUTH ELS header to assist in debugging session's state of authentication app. - FCD-207: qla2xxx: Fix stuck session of prli reject Changes: Remove the stale code that cause the unintentional short cut. - FCD-1197: qla2xxx: Throttling up is seen when port is down Changes: Reset the stats/congestion state and the throttling algorithm on a link down event. - FCD-348: qla2xxx: Reduce false trigger to login Changes: Reduce the extra trigger to prevent multiple login to the same session. - FCD-207: qla2xxx: edif : Reduce N2N thrashing at app_start time Changes: make sure the old session is torn down before triggering a relogin. - FCD-207: qla2xxx: Fix laggy FC remote port session recovery Changes: allows the higher priority error recovery to run first before running the lower priority heart beat check. - FCD-XXX: qla2xxx: edif: Fix no logout on delete for n2n Changes: Set a flag to turn on implicit logout early in the session recovery to make sure it would go out in case of error. - FCD-348: qla2xxx: edif: fix session thrash 2 Changes: prevents prli from going out before authentication app gives the ok - FCD-348: qla2xxx: edif: tear down session if keys has been removed Changes: If all keys for a session has been deleted then trigger a session tear down. - FCD-348: qla2xxx: edif: fix no login after app start Changes: Add a re-login trigger to relogin. - FCD-207: qla2xxx: Fix hang due to session stuck Changes: Break the requeue cycle and exit. The session deletion code will trigger a session relogin. - FCD-348: qla2xxx: edif: reduce disruption due to multiple app start Changes: Driver will skip over session tear down if app start is seen more than once. - FCD-348: qla2xxx: edif: send logo for unexpected ike msg Changes: Terminate/cleanup the AUTH ELS exchange.Follow with a pass through LOGO. - FCD-348: qla2xxx: edif: Fix IO timeout due to over subscription Changes: Track IOCB resources to prevent over subscription of IOCB resources - FCD-207: qla2xxx: edif: fix n2n login retry for secure device Changes: Add a few more login retries to revive the connection. - FCD-1205: qla2xxx: Fix disk failure to rediscover Changes: Set the online state before reporting to UL of the availability of the session. - FCD-207: qla2xxx: Fix n2n inconsistent plogi Changes: Delete the session to restart the connection, where ELS pass through PLOGI would be used consistently. - FCD-1267: qla2xxx: Fix crash during module load unload test Changes: Driver correctly freeing a pre-allocated structure for purex packet handling - FCD-XXX: qla2xxx: Fix missed DMA unmap for NVME ls requests. Changes: Add an unmap call during ELS completion. - FCD-1266: qla2xxx: Fix loss of NVME namespaces after driver reload test Changes: Calling the localport registration under a mutex - FCD-1212: qla2xxx: Host does not retry RDF when retries are exhausted and there is an incoming RDF Changes: Reset the SCM ELS counters to zero once an RDF is received. - FCD-XXX: qla2xxx: Restrict CPU-qpair mapping to work for NVMe only - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. - FCD-XXX: qla2xxx: SCM: Add a bitmap for FPIN events. - 10.02.07.00.a11-k1 BH 01/17/2022 - FCD-738: Fix T10 DIF performance on high end setup Changes: Added high performing CRC-1 interface - FCD-1182: qla2xxx: Fix initrd build error on RHEL 9 Changes: Updated the build script specific to RHEL 9 - FCD-XXX: qla2xxx: Fix incorrect latency counter display Changes: Fix this by ignoring I/Os with unusually high latencies. - FCD-207: qla2xxx: Fix n2n discovery issue with secure target Changes: On app_start, driver will reset the login retry attempt count. - FCD-1180: qla2xxx: Use correct feature type field during rffid processing Changes: Driver sends RFF_ID for initiator type 28 i.e. NVMe insteads of SCSI two times - FCD-1159: qla2xxx: Host doesn't retry the RDF/EDC when jammed with idle/CRC Changes: Wake up the DPC thread from the timer context when EDC/RDF needs to be - FCD-XXXX: qla2xxx: Build module with "-mindirect-branch=thunk-extern" option on RHEL 9 - 10.02.07.00.a10-k1 BH 01/06/2022 - FCD-XXX: qla2xxx: Support for changes in kernel 5.6 and above(rhel9.0) Changes: Changes made specific to rhel9.0 - FCD-1136: qla2xxx: Throttling occurs even when USCM is disabled via CLI Changes: Update flags that control USCM features, correctly on ISP reset - FCD-1160: USCM continues to be active even if RDF response is jammed (and failed) Changes: USCM flags are updated properly when port toggle and RDF completion happen - 10.02.07.00.a9-k1 BH 01/03/2022 - FCD-1154: qla2xxx: Fix incorrect reporting of task management failure Changes: Corrected endianness. - 10.02.07.00.a8-k1 BH 12/23/2021 - FCD-814 : qla2xxx: Add a new v2 dport diagnostic feature. Changes: Buffer size is increased to 1024 bytes and handle START/RESTART command received from SDMAPI. - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. Changes: Ramp up to faster initially, to get closer to the sweet spot quicker. Be less prone to operating at lower bandwidth in case of a sudden workload spike. Operate more conservatively (prioritize self over the network). - FCD-XXX: qla2xxx: Do not track SCM stats for all ports in the zone Changes: Track SCM stats just for the host and the target - FCD-XXX: qla2xxx: Stats for FPIN with event type "Lost Credit" not incremented. Changes: Add incrementing of "Lost Credit" stats. - FCD-684: qla2xxx: Fix link down when connected to AG fabric with FAA enabled Changes: Remove setting PUN and VL support bits in init control block. - FCD-1004: qla2xxx: Debug message improvement when changing SCM profile. Changes: Use profile names when changing profiles - FCD-868: qla2xxx: lockdown: "Unsupported Firmware" message Changes: checked different BITs for checking lockdown feature. - FCD-682: qla2xxx: tcm_qla2xxx driver load fails with "Invalid argument" error Changes: As tcm_qla2xxx is untested/unused, make it a dummy driver and reduce unncessary noise created by this. - FCD-886: qla2xxx: Hard Lockup on Unload/Load task with serial log enabled Changes: Hard lockup is seen because serial console driver crashed because of excessive logging. It was finalized to document this as known issues. - FCD-XXX: qla2xxx: Apply USCM profile change immediately - 10.02.07.00.a7-k1 BH 11/05/2021 - FCD-926: qla2xxx: lockdown: lower debug severity messages - FCD-824: qla2xxx: lower debug severity message for fw lockdown Changes: This patch lower the severity of various log messages. - FCD-XXX: qla2xxx: Send LS_ACC for an incoming RDF Changes: Send the LS_ACC and the new RDF separately - FCD-721: qla2xxx: Set Max queue depth based on data direction. Changes: Max q depth for Initiator tracks Reads (per port) and Fcport tracks Writes (per fcport). - FCD-701: qla2xxx: Fix device reconnect in loop topology Changes: Fix by taking the main login path that acquires device handle. - FCD-XXX: qla2xxx: Add ql2xnvme_queues module parameter to configure number of NVME queues - 10.02.07.00.a6-k1 BH 10/08/2021 - FCD-786: Shown wrong FDMI data for 64G adaptor Changes: qla2xxx: Corrected transmission speed mask values for FC - FCD-717: add retry for exe fw Changes: qla2xxx: Driver will retry Exec FW command up to 4 retries - FCD-XXX: qla2xxx: Compile out map queue changes if present in nvme-fc - 10.02.07.00.a5-k1 BH 10/01/2021 - FCD-740: Fix scheduling while atomic Changes: qla2xxx: schedule the call to fc_remote_port_delete in non-interrupt context - FCD-691: Fix premature hw access after pci error Changes: qla2xxx: Check error condition still persist and/or wait until the OS to give the resume signal - FCD-756: Fix excessive messages during device logout Changes: qla2xxx: disable printing IO error messages by default - FCD-XXX: qla2xxx: abort fw dump if soft reset fail - FCD-XXX: qla2xxx: USCM: Retry USCM ELS for Logical busy error code - FCD-XXX: qla2xxx: USCM: USCM profile reset to Driver defaults - FCD-XXX: qla2xxx: Fix warning message due to adisc is being flush at /var/log/messages - 10.02.07.00.a4-k1 BH 09/20/2021 - FCD-721: Revert code that keeps track of queue-depth directionally. Reason: Observing issue while q-depth accounting - FCD-XXX: Cleanup stale code. Changes: qla2xxx: Remove unused experimental code that uses explicit PRLO as a way to tear down session. - FCD-XXX: edif: remove old doorbell interface Changes: qla2xxx:driver has implemented a new doorbell mechanism via bsg. - FCD-348: edif: add retry for els pass through Changes: qla2xxx: edif: Add additional retries to reduce higher level recovery. - FCD-XXX: edif: Synchronize NPIV deletion with authentication application Changes: qla2xxx: Notify authentication application of a NPIV deletion event is about to occur. - FCD-XXX: edif: Fix potential stuck session in sa update Changes: qla2xxx: Set flag properly for any attempt to relogin. - FCD-704: The external flag for tcm_qla2xxx was not set. qla2xxx: Add tcm_qla2xxx to externally supported module list. - 10.02.07.00.a3-k1 BH 09/08/2021 - FCD-XXX: qla2xxx: edif: wait for app to ack on sess down Changes: On session deletion, wait for app to acknowledge before moving on. - FCD-XXX: qla2xxx: edif: fix edif bsg Changes: Properly fill out the reply_payload_rcv_len field. - FCD-XXX: qla2xxx: edif: fix inconsistent check of db_flags Changes: Replace value check with bit flag check. - FCD-XXX: qla2xxx: edif: increase ELS payload Changes: Adjust memory buffer size to be able to handle max ELS payload. - FCD-343: qla2xxx: turn off target reset during issue_lip Changes: driver sends additional target reset to remote device before resetting the link. - FCD-XXX: qla2xxx: edif: Reduce Initiator-Initiator thrashing. Changes: Reduce unnecessary stress for authentication application to deal with unused connections. - FCD-XXX: qla2xxx: fix gnl list corruption Changes: move lock deletion behind lock. - FCD-XXX: qla2xxx: edif: flush stale events and msgs on session down Changes: Prevents authentication application from having to process stale data. - FCD-XXX: qla2xxx: edif: reduces thrashing of the connection. - FCD-XXX: qla2xxx: edif: tweak trace message - FCD-XXX: qla2xxx: edif: fix app start delay - FCD-XXX: qla2xxx: USCM: Handle SCM ELS from switch - FCD-XXX: qla2xxx: edif: fix app start fail - 10.02.07.00.a2-k1 BH 09/02/2021 - FCD-156: qla2xxx: 3PAR: Fix out of bound mem access Changes: Add additional check to make sure the range of memory - FCD-624: qla2xxx: Source driver gives compilation error on RHEL8.5 Changes: Offending code on tcm_qla2xxx module has been removed - FCD-xxx: qla2xxx: Fix use after free Changes: Would check for command is aborted / completed by FW before exiting the call. - ER148553: qla2xxx: relogin during fabric disturbance Changes : Set the scan_need flag to indicate a session - FCD-464: qla2xxx: Fix race between timeout handler and completion handler Changes: One reference is taken for the normal code path and one for the timeout path - FCD-453: Fix FC-NVME register localport failure. Changes: Module initialization is added to nvme_fc_port_template - FCD-XXX: qla2xxx: Process responses in Tx path if any available for better performance Changes: Call process_response_queue() in Tx path - FCD-492: Kernel crashes when accessing port_speed sysfs file Changes: CNA: Fix this by changing the lookup. - FCD-XXX: qla2xxx: Refactor asynchronous command initialization - FCD-XXX: qla2xxx: USCM - Add profile support for throttling IO - FCD-XXX: qla2xxx: Move heart beat handling from dpc thread to workqueue - FCD-XXX: USCM: Enhancement to throttle only read traffic during host congestion and write traffic during target congestion. - 10.02.07.00.a1-k1 BH 08/22/2021 - FCD-124: qla2xxx: edif: Use link event to wake up app Changes: The link up event would notify app of the present of a new SCSI Host. - FCD-299: qla2xxx: Fix crash in NVME abort path Changes: Fixed the issue by removing stale access. - FCD-XXX: qla2xxx: Display 16G only as supported speeds for 3830c card. Changes: This card doesn't support lower speeds, hence, update the fdmi and sysfs fields to display 16G only. - FCD-226: qla2xxx: Update details for building kdump initrd in NVMe BFS. Changes: Currently inbox driver doesn't support kdump/kexec kernel, hence user need to update kdump initrd to have OOB driver part of it. - FCD-372: qla2xxx: Anomaly in the congestion stats Changes: Clear the signal counter on a qaucli clear - FCD-279: Request QCC to check/report adapter's MCTP state Changes: qla2xxx: Add support for mailbox passthru - FCD-XXX: Perf improvement: Pick qpair such that Tx and Rx are processed on same CPU. Changes: qla2xxx: Select qpair depending on which CPU post_cmd() gets called - FCD-XXX: scsi: qla2xxx: Reserve extra IRQ vectors - 10.02.06.02-k1 BH 08/11/2021 - FCD-511: Path does not go into "Marginal" state on receiving FPIN-LI Change: qla2xxx: Pass the LI events to the scsi_transport_fc - 10.02.06.01-k1 BH 07/27/2021 - ERXXXXXX: qla2xxx: Check for firmware capability before creating QPair. Change: Move the check for FW attributes to right location. This check is specific for ISP25XX. - 10.02.06.00-k1 BH 07/21/2021 - ERXXXXXX: qla2xxx: Version number is changed from 10.02.06.00.a1-k1 to 10.02.06.00-k1 - 10.02.06.00.a1-k1 BH 06/29/2021 - FCD-297: Fix NVME session down detection Change: qla2xxx: Session tear down and allow relogin to re-drive the connection under condition - ER148553/FCD-156: Fix NVME retry Change: qla2xxx: Alternate back and forth on every PRLI failure until login retry count has depleted or it is succeeded. - FCD-316: System crash when number of CPUs forced to 2 - Change: qla2xxx: Sync queue idx with queue_pair_map idx. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - ERXXXXXX: qla2xxx: Readme: Remove workaround of forcing of INTa mode for kdump kernel. - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - FCD-316: System crash when number of CPUs forced to 2 Changes : qla2xxx: prevents unbalanced QP allocation where nr_hw_queues is two less than the number of CPUs. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - FCD-268: Multiple USCM ELS are sent - FCD-280: Fix issues reported by running a few Jammer tests Changes: qla2xxx: Retry the USCM ELS 3 times when there are failures. - FCD-172: build.sh: Fix udev script installation error - ER148402: Install restrictions when binary rpm is already installed. Changes: qla2xxx: Updated README file for documentation - ERXXXXXX: qla2xxx: Support kdump kernel for NVMe BFS. - ERXXXXXX: qla2xxx: Update README file for building kdump initrd in NVMe BFS. - ER148402: Disallow install if qla2xxx rpm is installed. Changes: qla2xxx: Prevent install from source if rpm is installed. - FCD-230: Add additional debug logs Changes: qla2xxx: Add additional logs to differentiate between FW driver and driver driven ELS -FCD-XXXX: Changes to support kdump kernel. Changes: qla2xxx: Don't allocate fw dump for kexec kernel and Allocate single Q for kexec kernel. - FCD-227: Linux Driver order of RDF to follow EDC ELS - FCD-225 - Qaucli fails to list scm stats for Qlipper - FCD-172: fix udev rule Changes: qla2xxx: permission of the rule file set to 644 - ER148529: NVMe initiator connected to brocade fabric are down Changes: qla2xxx: Fix hang on NVME command timeouts. - ER148531: SN1600Q/SN1610Q, Gen10PlusSnap4 - Async-login failed errors on BFS boot-up-QXCR1001796980 Changes: qla2xxx: Suppress unnecessary log messages during login - ER148578: Observed that initiator is sending prli type 0x8 for for nvme ports Changes: qla2xxx: fix NVME | FCP personality change. - ER148141: Driver vmkmgt: Don't differentiate Signals and FPIN's for the Congestion counters when they detected. Changes: qla2xxx: Split congestion warnings and alarms based on signals and FPINs - ERXXXXXX: Add support for marginal path. Changes: qla2xxx: Added support for eh_should_retry_cmd callback in qla2xxx host template. - ERXXXXXX: scsi: qla2xxx: Flush all sessions on zone disable - ERXXXXXX: scsi: qla2xxx: Fix memory size truncation - ERXXXXXX: scsi: qla2xxx: Fix a NULL pointer dereference in an error path - ERXXXXXX: qla2xxx: fix sparse warning. - ERXXXXXX: qla2xxx: edif: do secure plogi when auth app is present - ERXXXXXX: qla2xxx: Add license. - ERXXXXXX: qla2xxx: USCM - Do not send EDC/RDF ELS when firmware has already sent it - ERXXXXXX: qla2xxx: Inclusion words are applied on release note and readme file - ERXXXXXX: qla2xxx: edif: add N2N support for EDIF - ERXXXXXX: qla2xxx: Updated drelease.notes header - ERXXXXXX: qla2xxx: Fix hang during NVME session tear down. - ERXXXXXX: qla2xxx: USCM: Cleaned up a few debug messages - ERXXXXXX: qla2xxx: edif: fix edif enable flag - ER148546: USCM: QCC Cong Mgmt not available on port with FW:v9.07.00 and DVR:v10.02.05.00.a6-k Changes: qla2xxx: setting the flags to indicate to the application that the RDF is complete and SCM is supported. - ERXXXXXX: Add heartbeat check Changes: qla2xxx: Use 'no-op' mailbox command to check to see if FW is still responsive. - ERXXXXXX: DEBUG: simulate FW hang. Changes: qla2xxx: Driver will detect the hang and recover via hearbeat check. - ERXXXXXX: qla2xxx: Check for FW attributes before enabling MQ. - ERXXXXXX: qla2xxx: USCM Handle ELS errors from switch by retrying 3 times - ERXXXXXX: scsi: qla2xxx: Correct the supported speeds for 16G Mezz card. - ER148472: With NPIV ports, link bounce causes loss of strongSwan session at the target. Changes: qla2xxx: : fix npiv create errorneous error qla2xxx: EDIF: reject AUTH ELS on session down. qla2xxx: edif: Fix stale session - ER148478: System Crash while NPIV RAW IO ON VPORT LUNS on SLES15 SP3 + QLE 2692 + R7525 Changes: qla2xxx: fix unsafe removal from link list. - ERXXXXXX: qla2xxx: USCM - Send EDC and RDF ELS from the driver - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: v2: fix crash in PCIe error handling - ER148123: Issue with Max secure connection with override_lower_limits Changes: qla2xxx: v2: fix stuck session - ER148402: SLES, Driver Install location is inconsistent. Changes: qla2xxx: Fix driver install location for SLES - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Changes: qla2xxx: edif: doorbell tweak - ER148448: Issue w.r.t qaucli, where Remote type "Unknown" for eDIF env. for qaucli2.4.0.build 20 Changes: qla2xxx: fix port type info - ER148433: The log does not show a valid data rate while the link speed is 64G. Changes: qla2xxx: fix debug print of 64G link speed. - ER147650: 'show fdmi? command does not list ? OS Name and Version? parameter for SLES12SP4-QXCR1001771822 Changes: qla2xxx: Show OS name and version in FDMI-1 - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: fix mailbox recovery during PCIE error qla2xxx: v2: fix crash in PCIe error handling - ERXXXXXX: qla2xxx: Changes to support FCP2 Target. - ERXXXXXX: qla2xxx: include AER debug mask to default - ERXXXXXX: qla2xxx: fixes for compilation on RH8.4 - ERXXXXXX: qla2xxx: Do logout even if fabric scan retries got exhausted. - 10.02.05.00.a1-k1 BH 02/27/2021 - EDIF Changes: - ER148247: issue with nvme-npiv env, once we delete npivs, after a while, it is reducing strongswan connections. Change: free sa index during npiv delete - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Change: adjust online|offline notification to app and tweak LOGO on session down. - ERXXXXXX: qla2xxx: edif: tweak log message - ERXXXXXX: qla2xxx: edif: Redundant code (already set in qla_edb_node_alloc) - ER147707: qla2xxx: Device recovery not happening and OS hungs on qla2xxx Change: Fix RISC RESET completion polling. - ER148111: qla2xxx: FCPowerKit reflects huge delays in CMDlets execution. Change: Check lockdown functionality before requesting lockdown feature. - ER148277: USCM: Linux Peer showing misleading 'Congested, throttling down, permitted: 1', prior to 'Reached low watermark, permitted: 2': - Change: Fix misleading debug message - ERXXXXXX: adjust request/respond queue size for 28xx - ERXXXXXX: qla2xxx: Change %p to %px in the log messages. - 10.02.01.00.a15-k1 BH 11/12/2020 ERXXXXXX: qla2xxx: Updated README file for new module parameters - 10.02.01.00.a14-k1 BH 11/06/2020 - ER146725: eDIF another driver panic running script: ./test_target_no_unload.sh Change: qla2xxx: Fix crash in qla_nvme_abort_set_option. - ER147771: Call Trace while shutting down the adapter ports (LINK DOWN). Change: qla2xxx: Handle aborts correctly for port undergoing deletion. - ERXXXXXX: qla2xxx: Add scsi_change_queue_depth to slave configure. - 10.02.01.00.a13-k1 BH 10/28/2020 - ER147600: Cisco: rpd ELS cmd fail to fetch the speed capabilities Change: qla2xxx: Used correct rdp spec, which was broken during code clean-up. - ER147695: FC-NVMe target discovery fails when initator wwpn < target wwpn in an N2N (Direct Attach) config Change: qla2xxx: fix N2N + NVME connect retry fail - ER147832: Issue with uSCM Linux with QCC CLI for some configuration Change: qla2xxx: Show event severity only when device state is congested. - ER147824 : scmr_stat sysfs node runs out of memory Change: qla2xxx: Come up with a compact version of scmr_stat - ER147823: NVMe IO is not getting throttled up or down. Change: qla2xxx: Enable throttle control for NVMe targets for Peer Congestion. - ERXXXXXX: qla2xxx: Count tgt short term link if link comes back before dev_loss_tmo. - ERXXXXXX: qla2xxx: Correct the check for fcport while displaying target counters. - ERXXXXXX: qla2xxx: Change trigger for host short term link down to dev loss tmo. - ERXXXXXX: qla2xxx: Move an SCM log under a debug level. - ERXXXXXX: qla2xxx: Set vendor_rsp[0] value. - ERXXXXXX: qla2xxx: Make throttling messages more informative. - 10.02.01.00.a12-k1 SK 10/15/2020 - ER147625: NVMe IO's are failing with Read/Write after LIP reset. Change: qla2xxx:Return EBUSY until the remote port delete finishes. - ER147653: Target side strongswan start/stop, make initiator crashed. Change: qla2xxx: edif: v2 fix double bsg done. - ER147791: USCM: clear option is not clearing hba alarm/warning, or clear cong or nvme target stats. Change: qla2xxx: Clear Sev and NVMe Target Stats. - ER147793: USCM: Throttling has wrong throttling up info and event period is not honored. Change: qla2xxx: Fix Throttling algorithm regression. - ER147759: NVMe Admin commands are getting throttled and causing admin queue failures. Change: qla2xxx: Throttle NVMe I/O commands only. - ERXXXXXX: qla2xxx: edif: fix aes_gmac mode. - ERXXXXXX: qla2xxx: edif: v2: standardize on port_id_t for bsg api. - ERXXXXXX: qla2xxx: edif: fix 4byte align. - ERXXXXXX: qla2xxx: edif: fix ELS meta data. - ERXXXXXX: qla2xxx: Clear Congestion State/Throttling during chip Reset. - ERXXXXXX: qla2xxx: Clear SCM Severity as part of SCM Stats Clear. - 10.02.00.02.a11-k1 BH 10/09/2020 - ER147734 : Lip reset on the isolated port causes server crash Change: qla2xxx: Don't allow FW, MPI and lip reset on isolated port. - ER147479 - PPC BE RH7.6 - qla2xxx driver loading - machine crashed. Change: qla2xxx: Fixes for big endian machines - ER147646: Call Trace observed while validating a MPI Pause test scenario. Change: qla2xxx: Correct the WARN_ON check in qla_nvme_abort_set_option. - ER147615: Throttling does not work with low I/Os. Change: qla2xxx: Check and round off fractional I/Os to 1 on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: List NVMe targets under scmr_stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Don't check for port isolation during abort isp. - ERXXXXXX: qla2xxx: SCM: Turn off SCM port parameter update mailbox command. - ERXXXXXX: qla2xxx: Fix I/O failures during remote port toggle testing - 10.02.00.02.a10-k1 BH 09/25/2020 SCM Changes: - ERXXXXXX: Changes - qla2xxx: Clear Congestion state when an RSCN is received/target is torn down. qla2xxx: throttling algorithm improvement. qla2xxx: Add throttling support for NVMe targets. EDIF Changes: - ERXXXXX: LUN loss on ipsec stop/start on target side. Change: save Nport on receive of PLOGI - ERXXXXX: fix ELS receive collision between physical and NPIV hosts. Change: remove erroneous source Nport ID search. - ER147570: FCP Performance Drop in latest driver for smaller IOs size. Change: qla2xxx: Change WQ_UNBOUND to WQ_MEM_RECLAIM. WQ_MEM_RECLAIM : wq is guaranteed to have at least one execution context regardless of memory pressure. - ER147632: QLE2774: RHEL 8.2 System crashes while upgrading he FW from 9.6.0 to 9.6.1 with QCC CLI build 12 Change: qla2xxx: Fix system crash on nvme abort path by checking sp of aborting command before accessing it. - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. - ER147645: System panic while trying to capture debugfs stats for EED. Change: qla2xxx: Check rport before accessing target number. - ER147632: Fix potential stale mem access Change: remove stale sp pointer reference - CQXXXXXX: FPIN events are not readily decodable. Change: qla2xxx: Make FPIN events prints human readable. - ER146879: Add support to clear SCM Stats Change: qla2xxx: Added support to clear SCM/SCMR Stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Allow get host stat during reset and sync reset. - ERXXXXXX: qla2xxx: Set reset_cmd_err_cnt on reset failure only. - ERXXXXXX: qla2xxx: Add isolated flag and return EPERM on isolation. - ERXXXXXX: qla2xxx: Count short term link if link comes back in 10 sec. - ERXXXXXX: qla2xxx: Don't check for fw_started while posting nvme command. - ERXXXXXX: qla2xxx: Pass irq_offset to blk_mq_pci_map_queues API. - ERXXXXXX: qla2xxx: lockdown: fix stale sp access. - BZ1868688: qla2xxx: tear down session if FW say its down. - 10.02.00.02.a9-k1 BH 09/03/2020 - ER147554 - sg_reset appears hung iterating over too many Qpairs. Change - qla2xxx: limit interrupt vectors to number of cpu. - ERXXXXX - qla2xxx: klocwork: Fix Bit field 'mpi_-' has one bit and is signed. - ERXXXXX - qla2xxx: Change post del message from debug level to log level. - ERXXXXX - qla2xxx: lockdown: fixup - Change error response as per API test. - ERXXXXX - qla2xxx: Fix map_queue interface to use the correct blk-mq call. - ERXXXXX - Added Structural changes for SCM Phase 2 support. Change : qla2xxx: Update structure definitions for SCM to support backward compatibility. - 10.02.00.02.a8-k1 BH 08/30/2020 - ERXXXXXX - Fix point-to-point (N2N) device discovery issue. Change - qla2xxx: Fix point-to-point (N2N) device discovery issue. - ERXXXXXX - To wait for ABTS response on I/O timeouts for NVMe. Change - qla2xxx: To wait for ABTS response on I/O timeouts for NVMe. - ER147523 - BSG stack trace and SCM display issues. Change - SCM: Functional regression with a6 release. - ER 147413 - edif: Fix issue with DIF enable target discovery. Change - qla2xxx: edif: Fix issue with DIF enable target discovery. - ER147480 clear ASYNC_ACTIVE flag to allow relogin. Change - qla2xxx: fix stuck session. - ERXXXXXX - lockdown: add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support - 10.02.00.02.a7-k1 BH 08/22/2020 - ER147495 - edif changes Change - qla2xxx: edif: fix nvme discovery failure qla2xxx: edif: fix els corruption. - ER147478 - SLES 15sp1 10.02...a6-k compile warning Change - qla2xxx: Compilation changes for sles15sp1 - ERXXXXXX - add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support qla2xxx: lockdown: fix compile problem. do not submit - ERXXXXXX: SCMR changes Change - qla2xxx: SCMR: Correct scmr_outstanding_reqs accounting. qla2xxx: SCM: Changes to separate current_events and current_state. qla2xxx: SCMR: Increase local array size. - ER147298 : USCM "Congestion Warning" counter regression Change - qla2xxx: Correct FPIN Structure Definition (Severity). - 10.02.00.02.a6-k1 BH 08/13/2020 - ERXXXXXX - fix crash on session cleanup + unload. Change - qla2xxx: fix crash on session cleanup + unload. - ER147329 - edif changes Change - qla2xxx: edif: fix compile error. do not submit qla2xxx: edif: fix double free on ELS send failure. qla2xxx: edif: reject els if non secure device. qla2xxx: edif: reject ELS on session down. qla2xxx: edif: redefine purex dest addr to be more consistent. qla2xxx: edif: tweak debug messages. qla2xxx: edif: fix nvme+edif target connect problem. - ER147460 - issue with Diag test on QCC CLI 2.4.0 build 10 with 10.2.00.2-a5 driver Change - qla2xxx: edif: move bsg auth els into separate routine. qla2xxx: edif: Fix error in BSG ELS path that has valid response data. - ER147312 - Add support to report MPI FW state. Change - qla2xxx: Add support to report MPI FW state. qla2xxx: Fix reset of MPI firmware. qla2xxx: Fix MPI reset needed message. - ER147437 - With a5 driver observed warning messages. Change - qla2xxx: Compilation changes for Citrix, rhel and sles. - 10.02.00.02.a5-k1 BH 07/31/2020 - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. Change - qla2xxx: Don't process target debugfs stats if port is isolated. - ERXXXXXX : Add SCM stats to scmr_stats node. Change - qla2xxx: Add SCM stats to scmr_stats node. - ER147419 : Fix crash due to request q pointer extraction failure. Change - qla2xxx: Latency measurement patch. - ERXXXXXX : edif: remove redundant field in port_id_t Change -qla2xxx: edif: remove redundant field in port_id_t - ER147331 - extract bbc from PLOGI template payload. Change -qla2xxx: Fix buffer-buffer credit extraction error - ERXXXXXX : Split qla2x00_configure_local_loop() Change scsi: qla2xxx: Split qla2x00_configure_local_loop() - ERXXXXXX : SCMR - Add I/O flow control. Change - qla2xxx: SCMR - Add I/O flow control. - 10.02.00.02.a4-k1 BH 07/23/2020 - ER147402 - Do not install nvme auto connect script if OS is installing it. Change - qla2xxx: auto-connect scripts are install based on nvme-cli package. - ERXXXXXX - Fixed return status of nvme fcp request. Change - qla2xxx: Set NVME status code for failed NVME FCP request. - ERXXXXXX - Multi-que support for TMF. Change - qla2xxx: Multi-que support for TMF. - ERXXXXXX ? edif changes Change - qla2xxx: edif: simplify reserve/release of sa_index. qla2xxx: edif: tweak debug log. qla2xxx: edif: adjust ELS resp length. qla2xxx: edif: send logo on app stop. qla2xxx: edif: remove prlo in session deletion. qla2xxx: edif: Fix app stop stall. - ER147298 - USCM "Congestion Warning" counter regression w/.65 driver. Change - qla2xxx: Correct fpin_descriptor definition. qla2xxx: Consolidate EDIF & SCM Purex Calls. - ERXXXXXX - Calculate avg. time taken by different components for IO completion. Change - qla2xxx: Latency measurement patch. - 10.02.00.02.a3-k1 BH 07/16/2020 - ER147348 - Observing firmware dump while running qaucli -g post port isolation. Change - qla2xxx: Don't check firmware state in case of chip is down. - ER147338 - SLES: Driver load failed - modprobe: ERROR: module 'qla2xxx' is unsupported. Change - qla2xxx: Add support for loading external modules on SuSE. - ER147361 - System panic after enabling port isolated during TimeOutReset. Change - qla2xxx: Synchronize the update the host counters using lock. - ER147370 - Hardware Error counter not incrementing for MBX command timeout. Change - qla2xxx: Update hardware error count for various error conditions. - ERXXXXXX - The change is to help in debuggging. Change - qla2xxx: Move some messages from debug to normal log level. - ER147346 - Observed a call trace after port isolation. Change - qla2xxx: Fix the call trace for flush workqueue. - ERXXXXXX - For debug purpose. Change - qla2xxx: Add error counters to debugfs node. - 10.02.00.02.a2-k1 AE 07/10/2020 - ERXXXXXX - qla2xxx: Fix TCM compilation issues. Change - Enabled build of tcm_qla2xxx module and fixed compile issues. - ERXXXXXX - qla2xxx: edif : Added back the app_stop wait and avoid if link is down. Change - Added wait during app stop. - ERXXXXXX - qla2xxx: Set BIT_13 for NVMe Async events. Change - Driver changes to skip SLER for Async event command. - ER147323 - qla2xxx: Correct the check for sscanf return value. Change - Driver updated to check version correctly. - ERXXXXXX - qla2xxx: v2: Add EDIF support. Change - Refactoring EDIF code for modularity. - ER147298 - Congestion Warning/Alarm counters fail to increment Change - Update driver to increment the counters for congestion signals. - 10.02.00.02.a1-k1 AE 06/29/2020 - qla2xxx: Enable IOCB throttling by default. - qla2xxx: Implementation to get and manage host, target stats and initiator port. - qla2xxx: Add SLER and PI control support. - qla2xxx: Do not log message when reading port speed via sysfs - qla2xxx: fix null pointer access. - qla2xxx: Use MPI hang trigger to do PEGTUNE halt. - qla2xxx: Reduce erroneous error in link reset path - qla2xxx: v2: fix stalled N2N reconnect. - qla2xxx: Fix warnings on SLES12SP5. - qla2xxx: Fix compilation issues on SLES15 - qla2xxx: Compilation Fixes for SLES15SP1. - qla2xxx: Debugfs compilation issue fix for RH7.6. - qla2xxx: Fix gcc test compile error output being printed. - qla2xxx: Timestamp device online and offline transitions. - qla2xxx: Add rport fields in debugfs. - qla2xxx: Allow dev_loss_tmo setting for FC-NVMe devices. - qla2xxx: Setup debugfs entries for remote ports. - qla2xxx: Fix edif related compilation issue on RH7.6. - Fixes for compilation on hpe branch - qla2xxx: Compilation fixes for RH8.2 - qla2xxx: Compilation changes for RH7.6 - qla2xxx: Fixes for compilation on RH7.x I - qla2xxx: bsg_job to bsg_job_t - qla2xxx: I Unify source code to work with newer kernels. - qla2xxx: Makefile changes from code-uni-devel-10x. - qla2xxx: qla_edif file changes to compile the driver. - qla2xxx: Fix compilation issues. - qla2xxx: Fix Makefile issue. - qla2xxx: fix compile error - qla2xxx: Use explicit LOGO in target mode - qla2xxx: Add EDIF support. - qla2xxx: Addd edif related files. - qla2xxx: Fix MPI failure AEN (8200) handling. - qla2xxx: SCM - Backport optimizations and style changes from upstream work. - qla2xxx: Fix warning in qla_attr.c file. - qla2xxx: Fix nvme compilation error. - qla2xxx: Fix crash in alloc w/GFP_KERNEL + interrupt - Author : Quinn Tran <qutran@marvell.com> qla2xxx: v2: add iocb resource tracking. - qla2xxx: Fix WARN_ON in qla_nvme_register_hba. - qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime. - qla2xxx: Make tgt_port_database available in initiator mode. - qla2xxx: reduce noisy debug message. - qla2xxx: Fix mailbox Ch erroneous error - qla2xxx: fix login timeout. - qla2xxx: Accomodate for SCM FW attribute bit change. - qla2xxx: post FC event (FPIN) to transport FPIN handler. - qla2xxx: Hide fc_host_fpin_rcv kernel dependency. - qla2xxx: Add changes to compile across various kernels. - qla2xxx: Use active targets to update SCM stats. - qla2xxx: Move SCM functions to qla_isr to keep changes local. - qla2xxx: Code to process FLOGI ACC extended payload. - qedf: Fix compilation issue - revisit. - qla2xxx: SCM Phase 1 Implementation + 2 other patches. - qla2xxx: Enable PUREX passthru post ISP reset. - qla2xxx: Fix hang when issuing nvme disconnect-all in NPIV. - qla2xxx: performance tweak - scsi: qla2xxx: fix fcport null pointer access. - fixup! qla2xxx: Fix unbound NVME response length. - scsi: qla2xxx: Fix unbound NVME response length - qla2xxx: Add host attribute to trigger MPI hang. - qla2xxx: ONEOFF: silent dbg messages for good path io. - qla2xxx: ONEOFF: fix pDIF detection - qla2xxx: Snoop inquiry response atleast 168 bytes to determine proprietary DIF. - qla2xxx: ONEOFF: add debug counters for T10-PI/DIF - qla2xxx: ONEOFF: add MQ support for HP3PAR propritary T10-PI - qla2xxx: HPE 3PAR private T10-PI support. - qla2xxx: Check for fabric_priority flag during login - qla2xxx: use iocb_fabric_priority flag - qla2xxx: Fix QoS name and add debug logs - qla2xxx: Correction to tests for iocb fabric and fcport qos. - qla2xxx: Use ->isp_ops->read_optrom() in qla26xx_read_qos_fcport_table(). - qla2xxx: QoS fcport table index initialization improvement. - qla2xxx: Add QoS fcport table index to speed up search. - qla2xxx: Reduce stack on qos fcport priority routines. - qla2xxx: HPE: Register FDMI QOS - qla2xxx: Add bsg interface for qos lun level bitmask. - qla2xxx: Read E2E QoS fcport priority bitmasks from flash. - qla2xxx: Abstract qos lun level mask for iocb cs_ctl field. - qla2xxx: Add fabric priority qos lun iocb mechanism. - qla2xxx: Implement CT command GFO (Get Fabric Object). - qla2xxx: Add support for fabric priority per target. - qla2xxx: fix mtcp dump collection failure. - qla2xxx: Set Nport ID for N2N - qla2xxx: Fix crash during device discovery. - qla2xxx: Handle NVME status iocb correctly. - qla2xxx: Remove restriction of FC T10-PI and NVME - qla2xxx: serialize fc_port alloc in N2N - qla2xxx: NPIV does not come up after FW dump. - qla2xxx: fix RDP respond data format bug. - qla2xxx: force semaphore on flash validation failure. - qla2xxx: add more FW debug information - qla2xxx: Revert: Disable T10-DIF feature with FC-NVMe during probe - qla2xxx: Update BPM enablement semantics. - qla2xxx: fix FW resource print error. - qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs. - qla2xxx: Ensure flash updates return possible failure status through bsg interface. - qla2xxx: Improved secure flash support messages - qla2xxx: fix flag passing error - qla2xxx: Use FC generic update firmware options routine for ISP27xx. - qla2xxx: Avoid setting firmware options twice in 24xx_update_fw_options. - qla2xxX: Add 16.0GT for PCI String - qla2xxx: Use FW_STARTED macro - qla2xxx: Add fixes for mailbox command - qla2xxx: Fix login IOCB flag - qla2xxx: Save rscn_gen for new fcport - qla2xxx: firmware option 3 is clobbered by speed set - qla2xxx: ISP28xx active FW region - qla2xxx: Add portname to print logs in qla24xx_logio_entry(). - qla2xxx: Correction to MB in-direction selection in qla2x00_echo_test(). - qla2xxx: Correction to selection of loopback/echo test. - qla2xxx: Use endian macros to assign static fields in fwdump header. - qla2xxx: Add Speed in SFP print information - qla2xxx: Fix RDP response size - qla2xxx: Handle cases for limiting RDP response payload length. - qla2xxx: Add deferred queue for processing ABTS and RDP. - qla2xxx: Cleanup ELS/PUREX iocb fields. - qla2xxx: Add devid's and conditionals for 28xx. - qla2xxx: Add vendor extended FDMI additions and amendments. - qla2xxx: Provide separate RDP enable. - qla2xxx: Add vendor extended RDP additions and amendments. - qla2xxx: Add changes in preparation for vendor extended FDMI/RDP. - qla2xxx: Add 2061 PCI ID - qla2xxx: Remove all DIX-0 references - qla2xxx: Add endianizer macro calls to fc host stats. - qla2xxx: Add sysfs node for D-Port Diagnostics AEN data. - qla2xxx: Move free of fcport out of interrupt context. - qla2xxx: Add beacon LED config sysfs interface. - qla2xxx: Add sysfs hooks for FC-NVMe autoconnect - 10.01.00.22-k AE 06/29/2020 - Upstream driver as part of Linux 5.6 - 10.02.14.00-k1 AG 05/21/2025 - - 10.02.14.00.a4-k1 AG 02/27/2025 [FCD-4186] : Device discovery fails on continuous reboot (Hitachi) Resolution : In a fabric topo when there is mismatch in state of login between driver and FW, query FW again and proceed with login Scope : 27xx/28xx Adapters [FCD-XXX] : Make functions local to a file static Resolution : Make functions local to a file static Scope : 27xx, 28xx series Adapters [FCD-XXX] : Remove unused function Resolution : Function qla25xx_set_purex is unused - remove it Scope : All adapters [FCD-4729] : Compilation errors with Sles15sp6 Resolution : Fix compilation errors on Sles15 SP6 Scope : Series Adapters [FCD-4536] : Compilation errors on RHEL10 Resolution : RHEL 10 has rebased to the latest kernel resulting in several build issues. Fix them and ensure that it builds on older kernels as well. Scope : Series Adapters [FCD-4676] : Add support for RH 9.6 (compilation) Resolution : Fix compilation errors on RH 9.6 Scope : Series Adapters [FCD-XXX] : Update README to reflect the supported distros Resolution : Update README to reflect the supported distros Scope : All Adapters Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com> Change-Id: Ic4af035fd48a3137923c7d3590be4271b0a7fd32 commit e22ea0921e20bcf93db0fae2b8dd579005686908 Author: Anil Gurumurthy <agurumurthy@marvell.com> Date: Fri Jan 10 11:06:14 2025 +0530 qla2xxx: Update driver version to 10.02.13.03-k1. - 10.02.13.03-k1 AG 01/10/2025 [FCD-4627] : HPSD5.10-BFS RHEL9.5 system crash on Nimble-HF40 failover test. Resolution : Check for sp being valid, before freeing associated memory Scope : All - 10.02.13.02-k1 MR 01/07/2025 [FCD-4657] : Fix SCSI INQ issue for supporting T10 DIF. Resolution : Replace sp completion with qpair completion call.. Scope : 28XX - 10.02.13.01-k1 MR 01/02/2025 [FCD-1040] : Call scsi done and nvme done with good completion without lock. Resolution : Done changes to move scsi done and nvme done without lock. Scope : 27xx and above - 10.02.13.00-k1 AG 10/22/2024 - - 10.02.13.00.a3-k1 SD 10/09/2024 [FCD-XXX] : Crash seen during load/unload test in a loop Resolution : Delay module unload when there is a fabric scan going on Scope : All adapters [FCD-4193] : SCSI device never recovers after RSCN Resolution : Remove tape specific checks which prevented recovery Scope : All adapters - 10.02.12.01-k1 MR 05/29/2024 [FCD-3465] : Server got crashed while running port toggle test. Resolution : During vport_delete send async_logout explicitly. Scope : 28XX - 10.02.12.00-k1 SD 05/20/2024 - - 10.02.12.00.a5-k1 SD 05/07/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a4-k1 SD 04/25/2024 [FCD-3970] : Crash while performing NPIV+FW reset test Resolution : Call sp->done inside lock Scope : All adapters [FCD-3947] : Supported speed displayed incorrectly for VPorts Resolution : The fc_function_template for vports did not have the supported_speeds field. Scope : All adapters - 10.02.12.00.a3-k1 SD 03/15/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : SFP cache on legacy adapter Scope : all - 10.02.12.00.a2-k1 SK 02/08/2024 [FCD-3797] : Driver installed using tarball failed to build initrd image after executing "./extras/build.sh initrd" command. Resolution : SLES15SP6 stop supporting mkinitrd command. Scope : ALL [FCD-xxx] : Fix NVME + NPIV connect issue Resolution : Initialize irq offset Scope : ALL - 10.02.12.00.a1-k1 QT 01/09/2024 scsi: qla2xxx: Drop redundant pci_enable_pcie_error_reporting() Resolution : Fix RHEL 9.4 compile issue Scope : ALL [FCD-3515] : API support for SFP data cache Scope : 27xx, 28xx [FCD-xxx] : Fix SLES15.6 compile issue Resolution : Remove stale fields Scope : ALL [FCD-3634] : Remove check req_sg_cnt should be equal to rsp_sg_cnt. Resolution : Firmware supports multiple sg_cnt for request and response for CT commands, so remove the redundant check. Scope : All Adapters [FCD-717] : Move FCE Trace buffer allocation to user control Resolution : Modify existing DFS knob to allow user to enable|disable this feature. Scope : Any [FCD-xxx] : Remove del_work work from qla_schedule_sess_for_deletion. Resolution : Remove del_work work from qla_schedule_sess_for_deletion. Scope : All [FCD-xxx] : Additional target mode code cleanup. Resolution : Additional target mode code cleanup. Scope : All [FCD-xxx] : Update copyright information. Resolution : Update copyright information. Scope : All [FCD-xxx] : Remove target code from qla_target files. Resolution : Remove target code from qla_target files. Scope : All [FCD-xxx] : Remove target mode code from initiator specific files. Resolution : Remove target mode code from initiator specific files. Scope : All [FCD-xxx] : Move common code to initiator specific files. Resolution : Move common code to initiator specific files. Scope : All [FCD-3751] : Fix use after free on unload Resolution : Remove duplicate signals on freeing dpc_thread Scope : ALL [FCD-3515] : Caching SFP data Scope : 27xx, 28xx [FCD-xxx] : Exec FW with delay Resolution : Add delay before command retry Scope : 28xx [FCD-xxx] : fix abort in bsg timeout Resolution : Wait for bsg to return before abort exit Scope : ALL [FCD-xxx] : Use QP lock to search for bsg. Resolution : use correct lock to protect search Scope : ALL [FCD-xxx] : Remove SQ in queuecommand Resolution : Remove duplicate code. Scope : ALL [FCD-xxx] : Reduce fabric scan duplicate code. Resolution : Consolidate routines that handle GPNFT & GNNFT. Scope : ALL [FCP-743] : Remove ql2xstay_attach_on_load_failure Resolution : Remove driver parameter used as part of feature test. Scope : 27xx, 28xx - 10.02.11.00-k1 NJ 10/25/2023 [FCD-xxx] : Remove PCI ID 0x2971 Resolution : Remove PCI ID 0x2971 Scope : [FCD-3661] : Remove 8031 from deprecate and unmaintained list. Resolution : Remove 8031 from deprecate and unmaintained list. Scope : 8031 [FCD-3571] : Unable to resume FW dump collection Resolution : send notification to udev Scope : 27xx, 28xx [FCD-3631] : Convert Port disable state to maintenance mode Resolution : Rename state and turn flag indicator Scope : 27xx + 28xx - 10.02.11.00.a8-k1 NJ 10/13/2023 [FCD-3632] : Remove support for FCoE device ids. Resolution : Remove FCoE ids from pci table. Scope : 8xxx [FCD-3624] : Fix optrom version displayed in FDMI Resolution : Populate EFI version Scope : Series Adapters [FCD-3632] : Remove CNA reference from README. Resolution : Remove CNA reference from README. Scope : 8xxx - 10.02.11.00.a7-k1 NJ 09/22/2023 [FCD-3195] : Fix flash read failure Resolution : Check return code for each flash read. Scope : Series Adapters [FCD-3571] : System flood by fw dumps Resolution : udev script to pause fw dump collection Scope : Any [FCD-3566] : Limit FW dump improvement to 27xx + 28xx Resolution : Add filter for 27xx + 28xx adapters Scope : 27xx+ [FCD-3497] : Return ENOBUFS if sg_cnt is more than one for ELS cmds. Resolution : This error is because FW support single sg element for ELS Pass-through IOCB (0x53h). This particular error code will help API and Apps to display appropriate message to the user. Scope : All Adapters [FCD-3510] : RHEL & SLES OOB driver request: deprecate L8/Hilda HW Resolution : Added a frame work to display the message based on device and OS. Scope : L8 and L16 (Hilda and CNA) [FCD-3269] : Init Control Block is dereferenced incorrectly Resolution : Correctly dereference ICB Scope : 20xx [FCD-3421] : Add Support to collect fw_dump on system crash or panic. Resolution : Add Support to collect fw_dump on system crash or panic Scope : 27xx, 28xx - 10.02.11.00.a6-k1 MR 09/08/2023 [FCD-XXX] : Modify error code handling for sfp fw upgrade mbx. Resolution : Modify error code handling for sfp fw upgrade mbx. Scope : 28xx [FCD-XXX] : Block sysfs resets and fw_dump during sfp fw upgrade Resolution : Block sysfs resets and fw_dump during sfp fw upgrade Scope : 28xx [FCP-743] : Block sysfs access during maintenance mode Resolution : Add check for maintenance mode. Scope : Any [FCD-3506] : Fix double free of dsd_list during driver load. Resolution : add pointer check before access Scope : Any - 10.02.11.00.a5-k1 MR 08/18/2023 [RH BZ 2039422] : NVMe-FC kernel crash during reload driver test Resolution : validate nvme_local_port correctly Scope : Any [FCD-XXX] : Fix for potential Null pointer dereferenced Resolution : Check before dereferencing pointer Scope : Any [FCP-743] : Enable driver attach to bad HW Resolution : turn on ql2xstay_attach_on_load_failure option Scope : 27xx, 28xx - 10.02.11.00.a4-k1 MR 08/11/2023 [FCD-xxx] : Update README file for zio information Resolution : Update readme file with zio information Scope : Any [FCD-3415] : Std-DIF is not working with HPe K1 driver Resolution : Reset the protect bit in the INQ response only when pDIF is enabled and negotiated. Scope : 26xx/27xx/28xx - 10.02.11.00.a3-k1 AG 08/03/2023 [FCP-743] : Allow only selective BSG requests in maintenance mode Resolution : Allow certain BSG to go through during maintenance mode Scope : Any [FCP-743] : FW dump improvement Resolution : Improve data capture Scope : 27XX, 28XX [FCD-3252] : Unable to act on RSCN for port online. Resolution : Clear RSCN flag only when driver is acting on the notification Scope : Any [FCD-xxx] : 32 Bytes CDB Resolution : Use Type 6 IOCB for CDB bigger than 16Bytes Scope : Any Unit Test : i) force IO to use Type6 only for over the weekend run. ii) force error path(s) to make sure no crash. [FCD-xxx] : Move resource to allow code reuse. Resolution : relocate dsd_list to qpair Scope : Any - 10.02.11.00.a2-k1 AG 07/27/2023 [FCD-3411] : CS_DMA Error observed while running DIF IO Resolution : While running DIF enabled IO, a CS_DMA error was observed. A FW dump is needed to better debug this. So take a FW dump on encountering this. Scope : 27xx/288 series of adapters [FCD-3406] : Modifiy default zio threshold value. Resolution : Modifiy default zio threshold value. Scope : 27xx/28xx Series Adapters [FCD-3314] : Delay IO Abort on PCI error Resolution : On detection of PCI error, allow IO's to wind down. Scope : Any [FCD-3314] : Fix system crash due to bad pointer access Resolution : Check SRB type before access. Scope : 27xx+ - 10.02.11.00.a1-k1 AG 07/14/2023 - FCP-749: qla2xxx: Add support for build for RH 9.3 and RH 8.9 distro Resolution : Build on RH 9.3 was failing owing to change of definition of fc_host_fpin_rcv and removal of DID_TARGET_FAILURE. Fix part of it by updating to latest upstream code. Scope : 27xx/28xx series of adapters - FCD-3302 : During unload Error detected messages is seen. Resolution : Change the wording of the message as its not an error. Scope : Series Adapters - FCD-3293 : Initiator sever getting crashed after LOGO. Resolution : Fix double free of fcport Scope : Any - Revert "scsi: qla2xxx: Change default ZIO threshold." This reverts commit 8812bcc1b7a25494ec8755ff3b61412a9993ff5b. The ZIO threshold now is 64. - FCD-xxx : Fix unreachable code Resolution : Remove dead code Scope : 28xx+ - FCD-3232 : Potential risk of double free pointer detected in Coverity scan by ran by Citrix Resolution : NULL the pointer after first free. Scope : All - 10.02.10.00-k1 SK 06/14/2023 Non-alpha build - 10.02.10.00.a2-k1 BH 05/12/2023 - FCD-3140: qla2xxx: Fix command flush on cable pull. Changes: Add wait for commands to return. - FCD-XXX: qla2xxx: NVME|FCP prefer flag not being honored. Changes: Reread prefer flag on chip reset - FCD-XXX: qla2xxx: Update readme file - 10.02.10.00.a1-k1 BH 05/02/2023 - FCD-XXX: qla2xxx: Update Copyright Changes: Update Copyright for Marvell. - FCD-XXX: qla2xxx: Update manufacturer detail Changes: Update manufacturer detail to "Marvell" - FCD-3140: qla2xxx: Host crash during StressAndHostPortReset test Changes: Remove unused nvme_ls_waitq wait queue. - FCD-XXX: qla2xxx: [RH-BZ 2167274]: Wait for io return on terminate rport. Changes: dd wait to terminate_rport_io - 10.02.09.00.a11-k1 BH 03/27/2023 - FCD-XXX: qla2xxx: Add link down + logo rx stat counts Changes: Add counters to track link down and Logo receive. - 10.02.09.00.a10-k1 BH 03/17/2023 - FCD-XXX: qla2xxx: Support for update SFP firmware of ACCELINK Changes: [New Feature] Support for update SFP FW of ACCELINK WTD 64G - FCD-717: qla2xxx: Split FCE|EFT trace control Changes: Split buffer alloc and enable of feature into individual step. - BZ-2093878: qla2xxx: perform lockless command completion in abort path Changes: Perform lockless command completion in abort path - 10.02.09.00.a9-k1 BH 03/06/2023 - FCD-2390: qla2xxx: Fix N2N stuck connection. Changes: Clear the blocking flag. - FCD-2496: qla2xxx: Prevent command send on chip reset Changes: Check for chip reset before sending IOCB. - FCD-2035: qla2xxx: Fix mem access after free. Changes: Remove access of memory - FCD-2720: qla2xxx: Move cmd_to_req_q latency counter before processing response. - FCD-XXX: qla2xxx: Update readme file for current program - 10.02.09.00.a8-k1 BH 02/27/2023 - FCD-2585: qla2xxx: Remove unsupported ql2xenabledif option. Changes: Removed unsupported ql2xenabledif=1 option and validate the user input. - FCD-2305: qla2xxx: Error code did not return to upper layer Changes: Preserve error code from TMF and return it to upper layer. - FCD-2035: qla2xxx: fix inconsistent TMF timeout. Changes: Allow TMF error to return to upper layer without session tear down. - FCD-2035: qla2xxx: Fix TMF leak through. Changes: Check for chip reset or session change before sending Task management. - 10.02.09.00.a7-k1 BH 02/17/2023 - FCD-2858: qla2xxx: USCM: Check for vp_idx before setting EDC and RDF set flags. Changes: Add check for vp_idx before setting EDC and RDF set flags when processing RIDA. Revert patch: - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition. - 10.02.09.00.a6-k1 BH 02/13/2023 - FCD-2750: qla2xxx: IO's are failing on Standard DIF enabled 3PAR LUN Changes: Revert an offending patch and work on an issue with upstream. - 10.02.09.00.a5-k1 BH 02/06/2023 - FCD-2858: qla2xxx: USCM: Remove EDC and RDF set flags on Report ID Acquisition Changes: Remove EDC and RDF set flags on Report ID Acquisition. - FCD-2879: qla2xxx: Compilation errors on SLES15SP5 Beta3-202301 Changes: Write generic code to find tag of scsi cmnd - FCD-2846: qla2xxx: Correct bsg_reply size in bsg interface Changes: Fix the bsg_job->reply_len with size of "struct fc_bsg_reply" - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the invariant expression in the condition - FCD-XXXX: qla2xxx: KW: unreachable code Changes: Remove the expression flogi_acc_pld_remaining == 0 - FCD-XXXX: qla2xxx: Changes of logs level for SFP temperature monitoring - 10.02.09.00.a4-k1 BH 01/29/2023 - FCD-2308: qla2xxx: Add bsg call to read port information Changes: Add bsg interface to allow app to read remote port information. - FCD-XXX: qla2xxx: KW-97439: unreachable code Changes: Return void if return value is not needed - FCD-XXX: qla2xxx: Add logs for SFP temperature monitoring Changes: Add debug log for Temperature Alert (8070h) Asynchronous Event - 10.02.09.00.a3-k1 BH 01/19/2023 - FCD-XXX: qla2xxx: Add support of RHEL9.2 - FCD-XXX: qla2xxx: Add support of RHEL8.8 - FCD-XXX: qla2xxx: Add support of SLES15 SP5 - FCD-2800: qla2xxx: Add support of OpenEuler-22.03 - 10.02.09.00.a2-k1 BH 01/10/2023 - FCD-XXX: qla2xxx: kw: unreachable code, SRB type is 0 just before latency counter incremented. Changes: SRB type is 0 just before latency counter incremented. - FCD-XXX: qla2xxx: kw: reset current_topology much later Changes: Reset current_topology much later on detecting - FCD-XXX: qla2xxx: kw: unreachable code, CS_COMPLETE is 0 and its already checked. Changes: Remove unreachable - FCD-XXX: qla2xxx: kw: Checking for port_state always yields zero Changes: Instead of bitwise AND check for port_state directly - FCD-1569: qla2xxx: Fix fw resource tracking Changes: Use global counter - FCD-XXX: qla2xxx: [ER-144639]: Flush mailbox commands on chip reset Changes: Use lock to prevent race condition. - FCD-2735: qla2xxx: USCM-VL: NVRAM VL disabled logins with extend FLOGI (VL enabled) Changes: Reset the spl. features control block flag to avoid logging in with ER_RDY. - FCD-XXX: qla2xxx: klockwork: Fix buffer over flow Changes: Use correct buffer size. - FCD-XXX: qla2xxx: EDIF: kw: remove unnecessary bit field - FCD-2563: qla2xxx: Turn off noisy message log. - FCD-XXX: qla2xxx: kw: remove dead code in qla24xx_config_rings - 10.02.09.00.a1-k1 BH 01/10/2023 - FCD-717: qla2xxx: allow FW dump extraction if load fail Changes: Add knob to force driver to stay attached to the fail adapter. - FCD-717: qla2xxx: Initialize FW buffer size with seed value Changes: Initialize FW Buffer size with seed value - FCD-XXX: qla2xxx: klockwork: Remove QLA_COMMAND_ERROR check in qla2x00_execute_fw. Changes: Remove the unnecessary QLA_COMMAND_ERROR check - FCD-2390: qla2xxx: Fix session hang in gnl Changes: Clear this flag to prevent blockage. - FCD-2390: qla2xxx: Fix erroneous link up failure Changes: Set fw_started flag early to prevent interrupts being dropped - FCD-2496: qla2xxx: Fix command flush during TMF Changes: Wait for commands flush before closing TMF - FCD-2035: qla2xxx: Limit TMF to 8 per function Changes: Limit TMF to 8 per function - FCD-XXX: qla2xxx: Add NVMe Disconnect support. Changes: Add support for NVMe Disconnect feature. - FCD-XXX: qla2xxx: Modify qla27xx_copy_fpin_pkt to support PURLS IOCB. Changes: Modified qla27xx_copy_fpin_pkt to support both PUREX and PURLS IOCBs. - FCD-717: qla2xxx: Adjust iocb resource on qpair create Changes: Add call to readjust iocb + exchange limit. - FCD-2390: qla2xxx: Fix deletion race condition Changes: Move check field behind lock - FCD-XXX: qla2xxx: klockwork: Pointer checked for NULL at linx x will be dereferenced at linx x+y. Changes: Remove the unnecessary Null check. The pointer will likely be valid. - FCD-XXX: qla2xxx: Observed call trace in smp_processor_id() with debug kernel Changes: Use raw_smp_processor_id API - FCD-2275: qla2xxx: USCM: Cleanup code related to IOPS based throttling Changes: IOPS and BW based throttling is not used. Remove those code. - FCD-2273: qla2xxx: USCM: Code cleanup w.r.t module params (ql2x_scmr_flow_ctl_tgt, ql2x_scmr_flow_ctl_host) Changes: Remove the redundant module parameters - FCD-2408: qla2xxx: USCM: Driver doesn't honor the adapter port Restore Default Settings Changes: Update the nvram values to the host as well as fcport - FCD-2363: qla2xxx: USCM: Slow Queue usage changes Changes: Use Slow queue only under specific scenarios - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Don't increment the counter for under-run. - FCD-2291: qla2xxx: Erroneous link down. Changes: Allow adapter reset to complete before discovery - FCD-2035: qla2xxx: Fix hang in task management Changes: Bail out of TMF on error - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path - FCD-XXX: qla2xxx: USCM: Debug log message improvement Changes: Log target WWPN for peer congestion - FCD-2164: qla2xxx: Fix stall session after app start Changes: Use session delete to avoid the accidental clearing of scan_flag - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Check fcport state before invoking the mailbox - FCD-XXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: Set throughput baseline on 1st FPIN - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix parsing the fpin when multiple descriptors are present - FCD-XXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCD-XXX: qla2xxx: USCM: Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: Fix for KW-97392 Changes :Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: Remove dead code - flagged by klocwork - FCD-847: qla2xxx: fixup: Fix exchange over subscription. - FCD-2434: qla2xxx: Fix crash when IO abort times out - FCD-XXX: qla2xxx: Rearrange scm rx path handling code. - 10.02.08.01-k1 BH 09/28/2022 - FCD-2392: Fix initrd image creation failure in OpenEuler, Kylin and UOS Changes: Add support for creating initrd image on openEuler, Kylin and UOS - 10.02.08.00-k1 BH 09/16/2022 - FCD-XXX: qla2xxx: Don't increment interface err cnt in SS_RESIDUAL_UNDER case. Changes: Residual under-run is not an interface error, hence no need to increment that count. - FCD-2291: qla2xxx: Fix erroneous link down. Changes: Allow adapter reset to complete before any scan can start. - FCD-2035: qla2xxx: Fix hang in task management Changes: Add additional error check at various point - FCD-XXX: qla2xxx: Reduce memory usage during low IO. Changes: Free the extra buffers as traffic is reduced. - 10.02.08.00.a7-k1 BH 08/22/2022 - FCD-2212: qla2xxx: USCM: Observed call trace during the rmmod qla2xxx module Changes: Free srb when throttle down I/O in NVME path. - FCD-2164: qla2xxx: USCM: Fix stall session after app start Changes: Prevent accidental clearing of flag that blocks re-login - FCD-2185: qla2xxx: USCM: Peer congestion throttling functionality doesn't honor the ISP reset/port toggle Changes: Clear the fcport throttling state on an ISP reset. - FCD-2194: qla2xxx: USCM: VL - Mailbox cmd failure during port toggle Changes: Heck fcport state before invoking mailbox - FCDXXX: qla2xxx: USCM: Debug log message improvement - 10.02.08.00.a6-k1 BH 08/09/2022 - FCDXXX: qla2xxx: USCM: VL - Enhance BW throttle to account for perf. drop while using VL Changes: if VL switchreduces the throughput below 50%, we would not throttle any further. - FCD-2096: qla2xxx: USCM: VL - PUN not incremented on PCN FPIN Changes: Fix the FPIN parsing to take into account multiple descriptors. - FCDXXX: qla2xxx: USCM: VL, Cache priority values from FLOGI_ACC Changes: Use priority values cached from FLOGI_ACC, when there is no PUN - FCDXXX: qla2xxx: USCM:Limit throttling down based on throughput Changes: Limit throttling down based on throughput - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..10 - 10.02.08.00.a5-k1 BH 07/29/2022 - FCD-XXX: qla2xxx: klocwork: Possible Null Pointer Dereference Changes: Validate rport before dereferencing - FCD-XXX: qla2xxx: klocwork: Array 'port_dstate_str' of size 10 may use index value(s) 10..15 Changes: Correct the index of array - FCD-XXX: qla2xxx: USCM: Fix mqueuecommand return code during throttle down request. - FCD-XXX: qla2xxx: Revert klockwork: Fix buffer overrun - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h - FCD-2035: qla2xxx: Fix Task Mgmt Cmd fail due to unavailable resource Changes: Limit TM commands to 8 per target. - 10.02.08.00.a4-k1 BH 07/23/2022 - FCD-847: qla2xxx: Fix exchange over subscription. Changes: check for exchange availability before command submission - FCD-XXX: qla2xxx: Remove unintended flag clearing Changes: Remove unintended flag clearing. - FCD-2035: qla2xxx: Fix task mgmt cmd fail with status 30h Changes: Add wait for completion of Marker! - FCD-XXX: Fix performance dip due to lock contention Changes: Save the allocated memory for reuse and avoid the lock - FCDXXX: qla2xxx: USCM: Do not send EDC and RDF for NPIV ports Changes: Disable sending USCM ELS for vports - FCDXXX: qla2xxx: USCM: VL: Do not set target speed to 1G for slow lane Changes: Do not set the target speed while changing lanes. - FCD-2012: qla2xxx: Throttling up messages seen when profile is changed Changes: Set the new profile for each fcport (along with the host). - FCD-XXX: qla2xxx: USCM: VL - Clean up FLOGI_ACC parsing Changes: structure that could be used to parse the FLOGI_ACC by using offsets - FCD-1990: qla2xxx: Fix nvram load config error Changes: Remove re-definition of port flags while enabling virtual lane support - FCD-XXX: qla2xxx: USCM:VL, I/O does not move back to the normal lane Changes: Check if I/O throttling is being done, before deciding to move the normal lane. - FCD-XXX: qla2xxx: Fix stall login Changes: Reset session state to allow relogin logic to re-drive the connection. - FCD-847: qla2xxx: Fix exchange over subscription for mgt cmd. Changes: would check for exchange availability before command submission. - FCD-847: qla2xxx: Fix exchange over subscription. Changes: would check for exchange availability before command submission. - FCD-XXX: qla2xxx: relocate/rename vp map. - FCD-XXX: qla2xxx: Klocwork: Fix for Unexpected type of a scan function parameter - 10.02.08.00.a3-k1 BH 07/01/2022 - FCD-1818: qla2xxx: Fix call trace in debug kernel due to missing spinlock init Changes: Fix the call trace by initializing trace lock. - FCD-1923: qla2xxx: USCM: VL - After disabling VL via CLI, status shows "Non-operational" Changes: Return VL status appropropriately - FCD-1922: qla2xxx: Fix discovery issues in FC-AL topology Changes: Checks FC loop map when Get ID list returns no device - FCD-1831: qla2xxx: Fix link failure in NIPV environment. Changes: Remove NPIV host from directly being able to chip reset. - FCD-XXX: qla2xxx: Fix DMA-API call trace on NVME LS requests with debug kernel Changes: Remove DMA mapping from the driver - FCD-XXX: qla2xxx: Fix KASAN use-after-free warning in qla24xx_sp_unmap Changes: Remove stale fcport access in qla2x00_rel_sp - FCD-XXX: qla2xxx: Fix KASAN out-of-bounds warning in qla_update_sp Changes: Size for memcpy was corrected to use the right length. - FCD-XXX: qla2xxx: Fix imbalance vha->vref_count Chnages: Add an extra ref count for the task management paths. - FCD-XXX: qla2xxx: Tweak Latency measurement Changes: Move the time read further ahead to the start of queuecommand and later to the point where it is just before scsi_done. - FCD-XXX: qla2xxx: klockwork: Silent superfluous warning. Changes: Remove superfluous Null check. - FCD-XXX: qla2xxx: klockwork: Fix buffer overrun Changes: Replace structure name to allow proper size calculation - FCD-XXX: qla2xxx: Remove dead code (GNN ID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code (GPNID). Changes: Remove stale/unused code. - FCD-XXX: qla2xxx: Remove dead code. Changes: Removing drport field and FCPORT_UPDATE_NEEDED, and EDIF_TICK_NEEDED signals - FCD-XXX: qla2xxx: Do not select slow queue if USCM is enabled Changes: Do not select slow queue whilie initializing cpu map - FCD-XXX: Select HW queue depending on Tx CPU Changes: Select qpair which is in correlation with Tx CPU - FCD-XXX: qla2xxx: Add support for displaying I/O throttle information Changes: Display the driver I/O throttle information along with VL information - FCD-XXX: qla2xxx: USCM: Throttle only R/W commands for NVME Changes: Throttle only read/write IOs. - Bring back following reverted changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.08.00.a2-k1 BH 06/19/2022 - FCD-XXX: qla2xxx: klockwork - Check valid rport returned by fc_bsg_to_rport Changes: Check valid rport returned by fc_bsg_to_rport - FCD-XXX: qla2xxx: klockwork - Check for a valid fcport pointer Changes: Add a check for a valid fcport pointer at the time of exit - FCD-XXX: qla2xxx: klockwork - Move fcport NULL check to avoid dereference Changes: Move the fcport NULL check to avoid the dereference. - FCD-1883: qla2xxx: USCM: Adapter shows "RDF Complete" when Link is down Changes: Reset the flag, so that when USCM is negotiated, the CLI shows the correct status - FCD-1846: qla2xxx: USCM: A log message while clearing stats Changes: Add a log message while clearing USCM stats - FCD-XXX: qla2xxx: USCM: VL-Reset FC device virtual lane priority to normal on a port flap Changes: Reset the virtual lane to normal on a port flap, ISP reset - FCD-XXX: qla2xxx: USCM: VL-Set target congestion before switching lanes Changes: Set the target state before the lane switch. - FCD-1752: qla2xxx: USCM: VL-Sysfs does not show Virtual Lane as enabled Changes: extended flogi_acc can also be parsed correctly. - FCD-1652: qla2xxx: Check if port is online before sending ELS Changes: Check if port is online before sending ELS - FCD-XXX: scsi: qla2xxx: Synchronize rport dev_loss_tmo setting - 10.02.08.00.a1-k1 BH 05/27/2022 - FCD-XXX: qla2xxx: USCM: Virtual Lane, Fix PUN handling Changes: Have a default priority range for each lane and ensure that the range is programmed correctly - FCD-XXX: qla2xxx: USCM: Support for Virtual Lanes Changes: Enable Virtual Lane support for Cisco switch - 10.02.07.00-k1 BH 05/27/2022 - Non-alpha build - 10.02.07.00.a19-k1 BH 05/21/2022 - FCD-XXX : qla2xxx: USCM: Throttling is not honored for NVMe Changes: Enable NVMe READ/WRITE commands to be throttled - FCD-XXX: qla2xxx: USCM: Add counters to track directional throttling Changes: Add sysfs counters to have stats displayed for busy status returns. - FCD-1801: qla2xxx: USCM: CP reads go to zero while doing directional throttling Changes: Take into account the directional queue depth while returning a busy status to the stack. - FCD-1809: qla2xxx: USCM: Restoring USCM Profile to default result in driver - FCD-1798: qla2xxx: USCM: Profiles are not honored for peer congestion Chnages: Apply the profile to each target (fcport) when the profile is changed. Reverting the following changes: - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - 10.02.07.00.a18-k1 BH 05/12/2022 - FCD-1484: qla2xxx: Manufacturer details should be "Marvell Semiconductor, Inc." Changes: Update Manufacturer details to indicate Marvell Semiconductors - FCD-XXX: qla2xxx: USCM: Throttle only read and write commands Changes: Throttle only read and write commands. - FCD-XXX: qla2xxx: USCM: Do not clear throttle for Clear Cong FPIN. Changes: Do not clear throttle when Clear Congestion FPIN is received. - FCD-XXX: qla2xxx: USCM: Change default profile to Monitor Changes: Set the default throttle profile as Monitor. - FCD-XXX: qla2xxx: Fix few issues reported by klocwork tool - 10.02.07.00.a17-k1 BH 05/06/2022 - FCD-1522: qla2xxx: USCM: Throughput drops to zero in Monitor mode Changes: Restore qdepth based on monitor mode - FCD-1315: qla2xxx: Fix erroneous mailbox timeout after pci error inject. Changes: Clear wait for MB interrupt flag to prevent stale MB completion arriving - FCD-1424: Remove verbose IO debug messages Changes: Remove the IOCB debug messages for every IO - FCD-XXX: Support for NVMe parameters in Auxiliary Image Status Changes: Added new structure member, bit define and image status check. - 10.02.07.00.a16-k1 BH 04/08/2022 - FCD-XXX: qla2xxx: qla2xxx: Add srb tracing Changes: Add a separate driver internal trace to capture srb related info. - FCD-XXX: qla2xxx: Add driver console messages tracing Changes: Logs are captured by default in an internal trace buffer depends on setting - FCD-XXX: qla2xxx: Add a generic tracing framework Changes: A rotating number of messages are captured in a trace structure - FCD-XXX: qla2xxx: Add debugfs create/delete helpers Changes: Define a few helpful macros for creating debugfs files. - FCD-1221: qla2xxx: USCM: Switch does not send FPINs after a EDC re-negotiation Changes: Send Link Service Request Information wih the EDC response, along with the other descriptors. - 10.02.07.00.a15-k1 BH 03/25/2022 - FCD-1249: qla2xxx: edif: Fix dropped IKE message. Changes: Fixes IKE message being dropped due to error in processing Purex IOCB and Continuation IOCBs. - FCD-1457: qla2xxx: Zero undefined mailbox IN registers Changes: Set zero to unuse register's value while requesting a new MB command. - FCD-1425: qla2xxx: USCM: Seconds since last event showing incorrect value Changes: Calculate delta time correctly - FCD-1287: qla2xxx: Fix incorrect display of max frame size. Changes: Save off the field of interest into separate location and convert into words. - FCD-XXX: qla2xxx: Fix memory leak when reading tgt_port_database debugfs file - FCD-XXX: qla2xxx: USCM: Do not reset SCM stats on a link bounce/ISP reset - 10.02.07.00.a14-k1 BH 03/14/2022 - FCD-XXX: qla2xxx: Fix losing FCP-2 targets on long port disable with IOs Changes: Fix this by accepting RSCN when the device is not online. - FCD-XXX: qla2xxx: Fix losing target when it reappears during delete Changes: Fix the issue by adding state checks before proceeding. - FCD-XXX: qla2xxx: Fix losing FCP-2 targets during port perturbation tests Changes: Fix was to ignore delete for FCP-2 devices in certain sequence. - FCD-119: qla2xxx: Fix crash due to stale srb access around IO timeouts Changes: Ensure srb is either returned during error IO timeout error escalation. If that is not possible fail the escalation path. - FCD-1132: qla2xxx: HPE3PAR: Fix IOCB resource count leak Changes: Decrement FW IOCB resource count. - FCD-1132: qla2xxx: Turn off MQ for 8G adapter. Changes: For 8G adapter, multi queue was enabled accidentally. - FCD-1385: Wind down adapter after pcie error. Changes: Detect the PCIE error and returns all IO's to upper layers. - FCD-1412: qla2xxx: Reset Congestion Warning/Alarm signals count. Changes: Reset signals at every signal check boundary (1 sec). - 10.02.07.00.a13-k1 BH 02/17/2022 - FCD-1353: qla2xx: a12/a11 driver compilation gives warning messages Changes: Fix the fall through warning - FCD-1342: qla2xxx: SL12SP5 a12 driver compilation issue observed Changes: fallthrough macro is defined based on gcc version. - 10.02.07.00.a12-k1 BH 02/09/2022 - FCD-XXX: qla2xxx: Reset USCM stats/state and throttling on RSCN Changes: Reset USCM stats on getting an RSCN indicating a target port down. - FCD-XXX: qla2xxx: Increase max limit of ql2xnvme_queues Changes: Increase max limit of ql2xnvme_queues to (max_qpair-1) - FCD-478: qla2xxx: Fix missing devices on a LOGO from F-Port Changes: A call to logo all ports is made upon a F-Port LOGO. - FCD-XXX: qla2xxx: Move NVMe traffic to the slow queue on target congestion Changes: Steer the NVMe traffic to the slow Q on encountering target congestion - FCD-348: qla2xxx: edif: Fix slow session tear down. Changes: As a work around, driver would trigger a session tear down where it tell the local authentication application to also tear down. - FCD-XXX: qla2xxx: edif: Tweak debug log. Changes: Print AUTH ELS header to assist in debugging session's state of authentication app. - FCD-207: qla2xxx: Fix stuck session of prli reject Changes: Remove the stale code that cause the unintentional short cut. - FCD-1197: qla2xxx: Throttling up is seen when port is down Changes: Reset the stats/congestion state and the throttling algorithm on a link down event. - FCD-348: qla2xxx: Reduce false trigger to login Changes: Reduce the extra trigger to prevent multiple login to the same session. - FCD-207: qla2xxx: edif : Reduce N2N thrashing at app_start time Changes: make sure the old session is torn down before triggering a relogin. - FCD-207: qla2xxx: Fix laggy FC remote port session recovery Changes: allows the higher priority error recovery to run first before running the lower priority heart beat check. - FCD-XXX: qla2xxx: edif: Fix no logout on delete for n2n Changes: Set a flag to turn on implicit logout early in the session recovery to make sure it would go out in case of error. - FCD-348: qla2xxx: edif: fix session thrash 2 Changes: prevents prli from going out before authentication app gives the ok - FCD-348: qla2xxx: edif: tear down session if keys has been removed Changes: If all keys for a session has been deleted then trigger a session tear down. - FCD-348: qla2xxx: edif: fix no login after app start Changes: Add a re-login trigger to relogin. - FCD-207: qla2xxx: Fix hang due to session stuck Changes: Break the requeue cycle and exit. The session deletion code will trigger a session relogin. - FCD-348: qla2xxx: edif: reduce disruption due to multiple app start Changes: Driver will skip over session tear down if app start is seen more than once. - FCD-348: qla2xxx: edif: send logo for unexpected ike msg Changes: Terminate/cleanup the AUTH ELS exchange.Follow with a pass through LOGO. - FCD-348: qla2xxx: edif: Fix IO timeout due to over subscription Changes: Track IOCB resources to prevent over subscription of IOCB resources - FCD-207: qla2xxx: edif: fix n2n login retry for secure device Changes: Add a few more login retries to revive the connection. - FCD-1205: qla2xxx: Fix disk failure to rediscover Changes: Set the online state before reporting to UL of the availability of the session. - FCD-207: qla2xxx: Fix n2n inconsistent plogi Changes: Delete the session to restart the connection, where ELS pass through PLOGI would be used consistently. - FCD-1267: qla2xxx: Fix crash during module load unload test Changes: Driver correctly freeing a pre-allocated structure for purex packet handling - FCD-XXX: qla2xxx: Fix missed DMA unmap for NVME ls requests. Changes: Add an unmap call during ELS completion. - FCD-1266: qla2xxx: Fix loss of NVME namespaces after driver reload test Changes: Calling the localport registration under a mutex - FCD-1212: qla2xxx: Host does not retry RDF when retries are exhausted and there is an incoming RDF Changes: Reset the SCM ELS counters to zero once an RDF is received. - FCD-XXX: qla2xxx: Restrict CPU-qpair mapping to work for NVMe only - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. - FCD-XXX: qla2xxx: SCM: Add a bitmap for FPIN events. - 10.02.07.00.a11-k1 BH 01/17/2022 - FCD-738: Fix T10 DIF performance on high end setup Changes: Added high performing CRC-1 interface - FCD-1182: qla2xxx: Fix initrd build error on RHEL 9 Changes: Updated the build script specific to RHEL 9 - FCD-XXX: qla2xxx: Fix incorrect latency counter display Changes: Fix this by ignoring I/Os with unusually high latencies. - FCD-207: qla2xxx: Fix n2n discovery issue with secure target Changes: On app_start, driver will reset the login retry attempt count. - FCD-1180: qla2xxx: Use correct feature type field during rffid processing Changes: Driver sends RFF_ID for initiator type 28 i.e. NVMe insteads of SCSI two times - FCD-1159: qla2xxx: Host doesn't retry the RDF/EDC when jammed with idle/CRC Changes: Wake up the DPC thread from the timer context when EDC/RDF needs to be - FCD-XXXX: qla2xxx: Build module with "-mindirect-branch=thunk-extern" option on RHEL 9 - 10.02.07.00.a10-k1 BH 01/06/2022 - FCD-XXX: qla2xxx: Support for changes in kernel 5.6 and above(rhel9.0) Changes: Changes made specific to rhel9.0 - FCD-1136: qla2xxx: Throttling occurs even when USCM is disabled via CLI Changes: Update flags that control USCM features, correctly on ISP reset - FCD-1160: USCM continues to be active even if RDF response is jammed (and failed) Changes: USCM flags are updated properly when port toggle and RDF completion happen - 10.02.07.00.a9-k1 BH 01/03/2022 - FCD-1154: qla2xxx: Fix incorrect reporting of task management failure Changes: Corrected endianness. - 10.02.07.00.a8-k1 BH 12/23/2021 - FCD-814 : qla2xxx: Add a new v2 dport diagnostic feature. Changes: Buffer size is increased to 1024 bytes and handle START/RESTART command received from SDMAPI. - FCD-XXX: qla2xxx: Change throttle up logic to be more aggressive. Changes: Ramp up to faster initially, to get closer to the sweet spot quicker. Be less prone to operating at lower bandwidth in case of a sudden workload spike. Operate more conservatively (prioritize self over the network). - FCD-XXX: qla2xxx: Do not track SCM stats for all ports in the zone Changes: Track SCM stats just for the host and the target - FCD-XXX: qla2xxx: Stats for FPIN with event type "Lost Credit" not incremented. Changes: Add incrementing of "Lost Credit" stats. - FCD-684: qla2xxx: Fix link down when connected to AG fabric with FAA enabled Changes: Remove setting PUN and VL support bits in init control block. - FCD-1004: qla2xxx: Debug message improvement when changing SCM profile. Changes: Use profile names when changing profiles - FCD-868: qla2xxx: lockdown: "Unsupported Firmware" message Changes: checked different BITs for checking lockdown feature. - FCD-682: qla2xxx: tcm_qla2xxx driver load fails with "Invalid argument" error Changes: As tcm_qla2xxx is untested/unused, make it a dummy driver and reduce unncessary noise created by this. - FCD-886: qla2xxx: Hard Lockup on Unload/Load task with serial log enabled Changes: Hard lockup is seen because serial console driver crashed because of excessive logging. It was finalized to document this as known issues. - FCD-XXX: qla2xxx: Apply USCM profile change immediately - 10.02.07.00.a7-k1 BH 11/05/2021 - FCD-926: qla2xxx: lockdown: lower debug severity messages - FCD-824: qla2xxx: lower debug severity message for fw lockdown Changes: This patch lower the severity of various log messages. - FCD-XXX: qla2xxx: Send LS_ACC for an incoming RDF Changes: Send the LS_ACC and the new RDF separately - FCD-721: qla2xxx: Set Max queue depth based on data direction. Changes: Max q depth for Initiator tracks Reads (per port) and Fcport tracks Writes (per fcport). - FCD-701: qla2xxx: Fix device reconnect in loop topology Changes: Fix by taking the main login path that acquires device handle. - FCD-XXX: qla2xxx: Add ql2xnvme_queues module parameter to configure number of NVME queues - 10.02.07.00.a6-k1 BH 10/08/2021 - FCD-786: Shown wrong FDMI data for 64G adaptor Changes: qla2xxx: Corrected transmission speed mask values for FC - FCD-717: add retry for exe fw Changes: qla2xxx: Driver will retry Exec FW command up to 4 retries - FCD-XXX: qla2xxx: Compile out map queue changes if present in nvme-fc - 10.02.07.00.a5-k1 BH 10/01/2021 - FCD-740: Fix scheduling while atomic Changes: qla2xxx: schedule the call to fc_remote_port_delete in non-interrupt context - FCD-691: Fix premature hw access after pci error Changes: qla2xxx: Check error condition still persist and/or wait until the OS to give the resume signal - FCD-756: Fix excessive messages during device logout Changes: qla2xxx: disable printing IO error messages by default - FCD-XXX: qla2xxx: abort fw dump if soft reset fail - FCD-XXX: qla2xxx: USCM: Retry USCM ELS for Logical busy error code - FCD-XXX: qla2xxx: USCM: USCM profile reset to Driver defaults - FCD-XXX: qla2xxx: Fix warning message due to adisc is being flush at /var/log/messages - 10.02.07.00.a4-k1 BH 09/20/2021 - FCD-721: Revert code that keeps track of queue-depth directionally. Reason: Observing issue while q-depth accounting - FCD-XXX: Cleanup stale code. Changes: qla2xxx: Remove unused experimental code that uses explicit PRLO as a way to tear down session. - FCD-XXX: edif: remove old doorbell interface Changes: qla2xxx:driver has implemented a new doorbell mechanism via bsg. - FCD-348: edif: add retry for els pass through Changes: qla2xxx: edif: Add additional retries to reduce higher level recovery. - FCD-XXX: edif: Synchronize NPIV deletion with authentication application Changes: qla2xxx: Notify authentication application of a NPIV deletion event is about to occur. - FCD-XXX: edif: Fix potential stuck session in sa update Changes: qla2xxx: Set flag properly for any attempt to relogin. - FCD-704: The external flag for tcm_qla2xxx was not set. qla2xxx: Add tcm_qla2xxx to externally supported module list. - 10.02.07.00.a3-k1 BH 09/08/2021 - FCD-XXX: qla2xxx: edif: wait for app to ack on sess down Changes: On session deletion, wait for app to acknowledge before moving on. - FCD-XXX: qla2xxx: edif: fix edif bsg Changes: Properly fill out the reply_payload_rcv_len field. - FCD-XXX: qla2xxx: edif: fix inconsistent check of db_flags Changes: Replace value check with bit flag check. - FCD-XXX: qla2xxx: edif: increase ELS payload Changes: Adjust memory buffer size to be able to handle max ELS payload. - FCD-343: qla2xxx: turn off target reset during issue_lip Changes: driver sends additional target reset to remote device before resetting the link. - FCD-XXX: qla2xxx: edif: Reduce Initiator-Initiator thrashing. Changes: Reduce unnecessary stress for authentication application to deal with unused connections. - FCD-XXX: qla2xxx: fix gnl list corruption Changes: move lock deletion behind lock. - FCD-XXX: qla2xxx: edif: flush stale events and msgs on session down Changes: Prevents authentication application from having to process stale data. - FCD-XXX: qla2xxx: edif: reduces thrashing of the connection. - FCD-XXX: qla2xxx: edif: tweak trace message - FCD-XXX: qla2xxx: edif: fix app start delay - FCD-XXX: qla2xxx: USCM: Handle SCM ELS from switch - FCD-XXX: qla2xxx: edif: fix app start fail - 10.02.07.00.a2-k1 BH 09/02/2021 - FCD-156: qla2xxx: 3PAR: Fix out of bound mem access Changes: Add additional check to make sure the range of memory - FCD-624: qla2xxx: Source driver gives compilation error on RHEL8.5 Changes: Offending code on tcm_qla2xxx module has been removed - FCD-xxx: qla2xxx: Fix use after free Changes: Would check for command is aborted / completed by FW before exiting the call. - ER148553: qla2xxx: relogin during fabric disturbance Changes : Set the scan_need flag to indicate a session - FCD-464: qla2xxx: Fix race between timeout handler and completion handler Changes: One reference is taken for the normal code path and one for the timeout path - FCD-453: Fix FC-NVME register localport failure. Changes: Module initialization is added to nvme_fc_port_template - FCD-XXX: qla2xxx: Process responses in Tx path if any available for better performance Changes: Call process_response_queue() in Tx path - FCD-492: Kernel crashes when accessing port_speed sysfs file Changes: CNA: Fix this by changing the lookup. - FCD-XXX: qla2xxx: Refactor asynchronous command initialization - FCD-XXX: qla2xxx: USCM - Add profile support for throttling IO - FCD-XXX: qla2xxx: Move heart beat handling from dpc thread to workqueue - FCD-XXX: USCM: Enhancement to throttle only read traffic during host congestion and write traffic during target congestion. - 10.02.07.00.a1-k1 BH 08/22/2021 - FCD-124: qla2xxx: edif: Use link event to wake up app Changes: The link up event would notify app of the present of a new SCSI Host. - FCD-299: qla2xxx: Fix crash in NVME abort path Changes: Fixed the issue by removing stale access. - FCD-XXX: qla2xxx: Display 16G only as supported speeds for 3830c card. Changes: This card doesn't support lower speeds, hence, update the fdmi and sysfs fields to display 16G only. - FCD-226: qla2xxx: Update details for building kdump initrd in NVMe BFS. Changes: Currently inbox driver doesn't support kdump/kexec kernel, hence user need to update kdump initrd to have OOB driver part of it. - FCD-372: qla2xxx: Anomaly in the congestion stats Changes: Clear the signal counter on a qaucli clear - FCD-279: Request QCC to check/report adapter's MCTP state Changes: qla2xxx: Add support for mailbox passthru - FCD-XXX: Perf improvement: Pick qpair such that Tx and Rx are processed on same CPU. Changes: qla2xxx: Select qpair depending on which CPU post_cmd() gets called - FCD-XXX: scsi: qla2xxx: Reserve extra IRQ vectors - 10.02.06.02-k1 BH 08/11/2021 - FCD-511: Path does not go into "Marginal" state on receiving FPIN-LI Change: qla2xxx: Pass the LI events to the scsi_transport_fc - 10.02.06.01-k1 BH 07/27/2021 - ERXXXXXX: qla2xxx: Check for firmware capability before creating QPair. Change: Move the check for FW attributes to right location. This check is specific for ISP25XX. - 10.02.06.00-k1 BH 07/21/2021 - ERXXXXXX: qla2xxx: Version number is changed from 10.02.06.00.a1-k1 to 10.02.06.00-k1 - 10.02.06.00.a1-k1 BH 06/29/2021 - FCD-297: Fix NVME session down detection Change: qla2xxx: Session tear down and allow relogin to re-drive the connection under condition - ER148553/FCD-156: Fix NVME retry Change: qla2xxx: Alternate back and forth on every PRLI failure until login retry count has depleted or it is succeeded. - FCD-316: System crash when number of CPUs forced to 2 - Change: qla2xxx: Sync queue idx with queue_pair_map idx. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - ERXXXXXX: qla2xxx: Readme: Remove workaround of forcing of INTa mode for kdump kernel. - ERXXXXXX: qla2xxx: Readme: Update OS details that supports NVMe BFS. - FCD-316: System crash when number of CPUs forced to 2 Changes : qla2xxx: prevents unbalanced QP allocation where nr_hw_queues is two less than the number of CPUs. This fix needs both commits released on 10.02.05.00-k and 10.02.06.00.a1-k against FCD-316 - FCD-268: Multiple USCM ELS are sent - FCD-280: Fix issues reported by running a few Jammer tests Changes: qla2xxx: Retry the USCM ELS 3 times when there are failures. - FCD-172: build.sh: Fix udev script installation error - ER148402: Install restrictions when binary rpm is already installed. Changes: qla2xxx: Updated README file for documentation - ERXXXXXX: qla2xxx: Support kdump kernel for NVMe BFS. - ERXXXXXX: qla2xxx: Update README file for building kdump initrd in NVMe BFS. - ER148402: Disallow install if qla2xxx rpm is installed. Changes: qla2xxx: Prevent install from source if rpm is installed. - FCD-230: Add additional debug logs Changes: qla2xxx: Add additional logs to differentiate between FW driver and driver driven ELS -FCD-XXXX: Changes to support kdump kernel. Changes: qla2xxx: Don't allocate fw dump for kexec kernel and Allocate single Q for kexec kernel. - FCD-227: Linux Driver order of RDF to follow EDC ELS - FCD-225 - Qaucli fails to list scm stats for Qlipper - FCD-172: fix udev rule Changes: qla2xxx: permission of the rule file set to 644 - ER148529: NVMe initiator connected to brocade fabric are down Changes: qla2xxx: Fix hang on NVME command timeouts. - ER148531: SN1600Q/SN1610Q, Gen10PlusSnap4 - Async-login failed errors on BFS boot-up-QXCR1001796980 Changes: qla2xxx: Suppress unnecessary log messages during login - ER148578: Observed that initiator is sending prli type 0x8 for for nvme ports Changes: qla2xxx: fix NVME | FCP personality change. - ER148141: Driver vmkmgt: Don't differentiate Signals and FPIN's for the Congestion counters when they detected. Changes: qla2xxx: Split congestion warnings and alarms based on signals and FPINs - ERXXXXXX: Add support for marginal path. Changes: qla2xxx: Added support for eh_should_retry_cmd callback in qla2xxx host template. - ERXXXXXX: scsi: qla2xxx: Flush all sessions on zone disable - ERXXXXXX: scsi: qla2xxx: Fix memory size truncation - ERXXXXXX: scsi: qla2xxx: Fix a NULL pointer dereference in an error path - ERXXXXXX: qla2xxx: fix sparse warning. - ERXXXXXX: qla2xxx: edif: do secure plogi when auth app is present - ERXXXXXX: qla2xxx: Add license. - ERXXXXXX: qla2xxx: USCM - Do not send EDC/RDF ELS when firmware has already sent it - ERXXXXXX: qla2xxx: Inclusion words are applied on release note and readme file - ERXXXXXX: qla2xxx: edif: add N2N support for EDIF - ERXXXXXX: qla2xxx: Updated drelease.notes header - ERXXXXXX: qla2xxx: Fix hang during NVME session tear down. - ERXXXXXX: qla2xxx: USCM: Cleaned up a few debug messages - ERXXXXXX: qla2xxx: edif: fix edif enable flag - ER148546: USCM: QCC Cong Mgmt not available on port with FW:v9.07.00 and DVR:v10.02.05.00.a6-k Changes: qla2xxx: setting the flags to indicate to the application that the RDF is complete and SCM is supported. - ERXXXXXX: Add heartbeat check Changes: qla2xxx: Use 'no-op' mailbox command to check to see if FW is still responsive. - ERXXXXXX: DEBUG: simulate FW hang. Changes: qla2xxx: Driver will detect the hang and recover via hearbeat check. - ERXXXXXX: qla2xxx: Check for FW attributes before enabling MQ. - ERXXXXXX: qla2xxx: USCM Handle ELS errors from switch by retrying 3 times - ERXXXXXX: scsi: qla2xxx: Correct the supported speeds for 16G Mezz card. - ER148472: With NPIV ports, link bounce causes loss of strongSwan session at the target. Changes: qla2xxx: : fix npiv create errorneous error qla2xxx: EDIF: reject AUTH ELS on session down. qla2xxx: edif: Fix stale session - ER148478: System Crash while NPIV RAW IO ON VPORT LUNS on SLES15 SP3 + QLE 2692 + R7525 Changes: qla2xxx: fix unsafe removal from link list. - ERXXXXXX: qla2xxx: USCM - Send EDC and RDF ELS from the driver - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: v2: fix crash in PCIe error handling - ER148123: Issue with Max secure connection with override_lower_limits Changes: qla2xxx: v2: fix stuck session - ER148402: SLES, Driver Install location is inconsistent. Changes: qla2xxx: Fix driver install location for SLES - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Changes: qla2xxx: edif: doorbell tweak - ER148448: Issue w.r.t qaucli, where Remote type "Unknown" for eDIF env. for qaucli2.4.0.build 20 Changes: qla2xxx: fix port type info - ER148433: The log does not show a valid data rate while the link speed is 64G. Changes: qla2xxx: fix debug print of 64G link speed. - ER147650: 'show fdmi? command does not list ? OS Name and Version? parameter for SLES12SP4-QXCR1001771822 Changes: qla2xxx: Show OS name and version in FDMI-1 - ER147707: Device recovery not happening and OS hungs on qla2xxx Changes: qla2xxx: fix mailbox recovery during PCIE error qla2xxx: v2: fix crash in PCIe error handling - ERXXXXXX: qla2xxx: Changes to support FCP2 Target. - ERXXXXXX: qla2xxx: include AER debug mask to default - ERXXXXXX: qla2xxx: fixes for compilation on RH8.4 - ERXXXXXX: qla2xxx: Do logout even if fabric scan retries got exhausted. - 10.02.05.00.a1-k1 BH 02/27/2021 - EDIF Changes: - ER148247: issue with nvme-npiv env, once we delete npivs, after a while, it is reducing strongswan connections. Change: free sa index during npiv delete - ER148123: Issue with Max secure connection with override_lower_limits set and rekey/reauth with240/480-luns disconnected after 2 hr traffi Change: adjust online|offline notification to app and tweak LOGO on session down. - ERXXXXXX: qla2xxx: edif: tweak log message - ERXXXXXX: qla2xxx: edif: Redundant code (already set in qla_edb_node_alloc) - ER147707: qla2xxx: Device recovery not happening and OS hungs on qla2xxx Change: Fix RISC RESET completion polling. - ER148111: qla2xxx: FCPowerKit reflects huge delays in CMDlets execution. Change: Check lockdown functionality before requesting lockdown feature. - ER148277: USCM: Linux Peer showing misleading 'Congested, throttling down, permitted: 1', prior to 'Reached low watermark, permitted: 2': - Change: Fix misleading debug message - ERXXXXXX: adjust request/respond queue size for 28xx - ERXXXXXX: qla2xxx: Change %p to %px in the log messages. - 10.02.01.00.a15-k1 BH 11/12/2020 ERXXXXXX: qla2xxx: Updated README file for new module parameters - 10.02.01.00.a14-k1 BH 11/06/2020 - ER146725: eDIF another driver panic running script: ./test_target_no_unload.sh Change: qla2xxx: Fix crash in qla_nvme_abort_set_option. - ER147771: Call Trace while shutting down the adapter ports (LINK DOWN). Change: qla2xxx: Handle aborts correctly for port undergoing deletion. - ERXXXXXX: qla2xxx: Add scsi_change_queue_depth to slave configure. - 10.02.01.00.a13-k1 BH 10/28/2020 - ER147600: Cisco: rpd ELS cmd fail to fetch the speed capabilities Change: qla2xxx: Used correct rdp spec, which was broken during code clean-up. - ER147695: FC-NVMe target discovery fails when initator wwpn < target wwpn in an N2N (Direct Attach) config Change: qla2xxx: fix N2N + NVME connect retry fail - ER147832: Issue with uSCM Linux with QCC CLI for some configuration Change: qla2xxx: Show event severity only when device state is congested. - ER147824 : scmr_stat sysfs node runs out of memory Change: qla2xxx: Come up with a compact version of scmr_stat - ER147823: NVMe IO is not getting throttled up or down. Change: qla2xxx: Enable throttle control for NVMe targets for Peer Congestion. - ERXXXXXX: qla2xxx: Count tgt short term link if link comes back before dev_loss_tmo. - ERXXXXXX: qla2xxx: Correct the check for fcport while displaying target counters. - ERXXXXXX: qla2xxx: Change trigger for host short term link down to dev loss tmo. - ERXXXXXX: qla2xxx: Move an SCM log under a debug level. - ERXXXXXX: qla2xxx: Set vendor_rsp[0] value. - ERXXXXXX: qla2xxx: Make throttling messages more informative. - 10.02.01.00.a12-k1 SK 10/15/2020 - ER147625: NVMe IO's are failing with Read/Write after LIP reset. Change: qla2xxx:Return EBUSY until the remote port delete finishes. - ER147653: Target side strongswan start/stop, make initiator crashed. Change: qla2xxx: edif: v2 fix double bsg done. - ER147791: USCM: clear option is not clearing hba alarm/warning, or clear cong or nvme target stats. Change: qla2xxx: Clear Sev and NVMe Target Stats. - ER147793: USCM: Throttling has wrong throttling up info and event period is not honored. Change: qla2xxx: Fix Throttling algorithm regression. - ER147759: NVMe Admin commands are getting throttled and causing admin queue failures. Change: qla2xxx: Throttle NVMe I/O commands only. - ERXXXXXX: qla2xxx: edif: fix aes_gmac mode. - ERXXXXXX: qla2xxx: edif: v2: standardize on port_id_t for bsg api. - ERXXXXXX: qla2xxx: edif: fix 4byte align. - ERXXXXXX: qla2xxx: edif: fix ELS meta data. - ERXXXXXX: qla2xxx: Clear Congestion State/Throttling during chip Reset. - ERXXXXXX: qla2xxx: Clear SCM Severity as part of SCM Stats Clear. - 10.02.00.02.a11-k1 BH 10/09/2020 - ER147734 : Lip reset on the isolated port causes server crash Change: qla2xxx: Don't allow FW, MPI and lip reset on isolated port. - ER147479 - PPC BE RH7.6 - qla2xxx driver loading - machine crashed. Change: qla2xxx: Fixes for big endian machines - ER147646: Call Trace observed while validating a MPI Pause test scenario. Change: qla2xxx: Correct the WARN_ON check in qla_nvme_abort_set_option. - ER147615: Throttling does not work with low I/Os. Change: qla2xxx: Check and round off fractional I/Os to 1 on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: List NVMe targets under scmr_stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Don't check for port isolation during abort isp. - ERXXXXXX: qla2xxx: SCM: Turn off SCM port parameter update mailbox command. - ERXXXXXX: qla2xxx: Fix I/O failures during remote port toggle testing - 10.02.00.02.a10-k1 BH 09/25/2020 SCM Changes: - ERXXXXXX: Changes - qla2xxx: Clear Congestion state when an RSCN is received/target is torn down. qla2xxx: throttling algorithm improvement. qla2xxx: Add throttling support for NVMe targets. EDIF Changes: - ERXXXXX: LUN loss on ipsec stop/start on target side. Change: save Nport on receive of PLOGI - ERXXXXX: fix ELS receive collision between physical and NPIV hosts. Change: remove erroneous source Nport ID search. - ER147570: FCP Performance Drop in latest driver for smaller IOs size. Change: qla2xxx: Change WQ_UNBOUND to WQ_MEM_RECLAIM. WQ_MEM_RECLAIM : wq is guaranteed to have at least one execution context regardless of memory pressure. - ER147632: QLE2774: RHEL 8.2 System crashes while upgrading he FW from 9.6.0 to 9.6.1 with QCC CLI build 12 Change: qla2xxx: Fix system crash on nvme abort path by checking sp of aborting command before accessing it. - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. - ER147645: System panic while trying to capture debugfs stats for EED. Change: qla2xxx: Check rport before accessing target number. - ER147632: Fix potential stale mem access Change: remove stale sp pointer reference - CQXXXXXX: FPIN events are not readily decodable. Change: qla2xxx: Make FPIN events prints human readable. - ER146879: Add support to clear SCM Stats Change: qla2xxx: Added support to clear SCM/SCMR Stats on ISP 27xx/28xx Series Adapters - ERXXXXXX: qla2xxx: Allow get host stat during reset and sync reset. - ERXXXXXX: qla2xxx: Set reset_cmd_err_cnt on reset failure only. - ERXXXXXX: qla2xxx: Add isolated flag and return EPERM on isolation. - ERXXXXXX: qla2xxx: Count short term link if link comes back in 10 sec. - ERXXXXXX: qla2xxx: Don't check for fw_started while posting nvme command. - ERXXXXXX: qla2xxx: Pass irq_offset to blk_mq_pci_map_queues API. - ERXXXXXX: qla2xxx: lockdown: fix stale sp access. - BZ1868688: qla2xxx: tear down session if FW say its down. - 10.02.00.02.a9-k1 BH 09/03/2020 - ER147554 - sg_reset appears hung iterating over too many Qpairs. Change - qla2xxx: limit interrupt vectors to number of cpu. - ERXXXXX - qla2xxx: klocwork: Fix Bit field 'mpi_-' has one bit and is signed. - ERXXXXX - qla2xxx: Change post del message from debug level to log level. - ERXXXXX - qla2xxx: lockdown: fixup - Change error response as per API test. - ERXXXXX - qla2xxx: Fix map_queue interface to use the correct blk-mq call. - ERXXXXX - Added Structural changes for SCM Phase 2 support. Change : qla2xxx: Update structure definitions for SCM to support backward compatibility. - 10.02.00.02.a8-k1 BH 08/30/2020 - ERXXXXXX - Fix point-to-point (N2N) device discovery issue. Change - qla2xxx: Fix point-to-point (N2N) device discovery issue. - ERXXXXXX - To wait for ABTS response on I/O timeouts for NVMe. Change - qla2xxx: To wait for ABTS response on I/O timeouts for NVMe. - ER147523 - BSG stack trace and SCM display issues. Change - SCM: Functional regression with a6 release. - ER 147413 - edif: Fix issue with DIF enable target discovery. Change - qla2xxx: edif: Fix issue with DIF enable target discovery. - ER147480 clear ASYNC_ACTIVE flag to allow relogin. Change - qla2xxx: fix stuck session. - ERXXXXXX - lockdown: add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support - 10.02.00.02.a7-k1 BH 08/22/2020 - ER147495 - edif changes Change - qla2xxx: edif: fix nvme discovery failure qla2xxx: edif: fix els corruption. - ER147478 - SLES 15sp1 10.02...a6-k compile warning Change - qla2xxx: Compilation changes for sles15sp1 - ERXXXXXX - add mpi flash lock down support Change - qla2xxx: lockdown: add mpi flash lock down support qla2xxx: lockdown: fix compile problem. do not submit - ERXXXXXX: SCMR changes Change - qla2xxx: SCMR: Correct scmr_outstanding_reqs accounting. qla2xxx: SCM: Changes to separate current_events and current_state. qla2xxx: SCMR: Increase local array size. - ER147298 : USCM "Congestion Warning" counter regression Change - qla2xxx: Correct FPIN Structure Definition (Severity). - 10.02.00.02.a6-k1 BH 08/13/2020 - ERXXXXXX - fix crash on session cleanup + unload. Change - qla2xxx: fix crash on session cleanup + unload. - ER147329 - edif changes Change - qla2xxx: edif: fix compile error. do not submit qla2xxx: edif: fix double free on ELS send failure. qla2xxx: edif: reject els if non secure device. qla2xxx: edif: reject ELS on session down. qla2xxx: edif: redefine purex dest addr to be more consistent. qla2xxx: edif: tweak debug messages. qla2xxx: edif: fix nvme+edif target connect problem. - ER147460 - issue with Diag test on QCC CLI 2.4.0 build 10 with 10.2.00.2-a5 driver Change - qla2xxx: edif: move bsg auth els into separate routine. qla2xxx: edif: Fix error in BSG ELS path that has valid response data. - ER147312 - Add support to report MPI FW state. Change - qla2xxx: Add support to report MPI FW state. qla2xxx: Fix reset of MPI firmware. qla2xxx: Fix MPI reset needed message. - ER147437 - With a5 driver observed warning messages. Change - qla2xxx: Compilation changes for Citrix, rhel and sles. - 10.02.00.02.a5-k1 BH 07/31/2020 - ER147418: server crash seen when trying to capture the debugfs stat on isolated port. Change - qla2xxx: Don't process target debugfs stats if port is isolated. - ERXXXXXX : Add SCM stats to scmr_stats node. Change - qla2xxx: Add SCM stats to scmr_stats node. - ER147419 : Fix crash due to request q pointer extraction failure. Change - qla2xxx: Latency measurement patch. - ERXXXXXX : edif: remove redundant field in port_id_t Change -qla2xxx: edif: remove redundant field in port_id_t - ER147331 - extract bbc from PLOGI template payload. Change -qla2xxx: Fix buffer-buffer credit extraction error - ERXXXXXX : Split qla2x00_configure_local_loop() Change scsi: qla2xxx: Split qla2x00_configure_local_loop() - ERXXXXXX : SCMR - Add I/O flow control. Change - qla2xxx: SCMR - Add I/O flow control. - 10.02.00.02.a4-k1 BH 07/23/2020 - ER147402 - Do not install nvme auto connect script if OS is installing it. Change - qla2xxx: auto-connect scripts are install based on nvme-cli package. - ERXXXXXX - Fixed return status of nvme fcp request. Change - qla2xxx: Set NVME status code for failed NVME FCP request. - ERXXXXXX - Multi-que support for TMF. Change - qla2xxx: Multi-que support for TMF. - ERXXXXXX ? edif changes Change - qla2xxx: edif: simplify reserve/release of sa_index. qla2xxx: edif: tweak debug log. qla2xxx: edif: adjust ELS resp length. qla2xxx: edif: send logo on app stop. qla2xxx: edif: remove prlo in session deletion. qla2xxx: edif: Fix app stop stall. - ER147298 - USCM "Congestion Warning" counter regression w/.65 driver. Change - qla2xxx: Correct fpin_descriptor definition. qla2xxx: Consolidate EDIF & SCM Purex Calls. - ERXXXXXX - Calculate avg. time taken by different components for IO completion. Change - qla2xxx: Latency measurement patch. - 10.02.00.02.a3-k1 BH 07/16/2020 - ER147348 - Observing firmware dump while running qaucli -g post port isolation. Change - qla2xxx: Don't check firmware state in case of chip is down. - ER147338 - SLES: Driver load failed - modprobe: ERROR: module 'qla2xxx' is unsupported. Change - qla2xxx: Add support for loading external modules on SuSE. - ER147361 - System panic after enabling port isolated during TimeOutReset. Change - qla2xxx: Synchronize the update the host counters using lock. - ER147370 - Hardware Error counter not incrementing for MBX command timeout. Change - qla2xxx: Update hardware error count for various error conditions. - ERXXXXXX - The change is to help in debuggging. Change - qla2xxx: Move some messages from debug to normal log level. - ER147346 - Observed a call trace after port isolation. Change - qla2xxx: Fix the call trace for flush workqueue. - ERXXXXXX - For debug purpose. Change - qla2xxx: Add error counters to debugfs node. - 10.02.00.02.a2-k1 AE 07/10/2020 - ERXXXXXX - qla2xxx: Fix TCM compilation issues. Change - Enabled build of tcm_qla2xxx module and fixed compile issues. - ERXXXXXX - qla2xxx: edif : Added back the app_stop wait and avoid if link is down. Change - Added wait during app stop. - ERXXXXXX - qla2xxx: Set BIT_13 for NVMe Async events. Change - Driver changes to skip SLER for Async event command. - ER147323 - qla2xxx: Correct the check for sscanf return value. Change - Driver updated to check version correctly. - ERXXXXXX - qla2xxx: v2: Add EDIF support. Change - Refactoring EDIF code for modularity. - ER147298 - Congestion Warning/Alarm counters fail to increment Change - Update driver to increment the counters for congestion signals. - 10.02.00.02.a1-k1 AE 06/29/2020 - qla2xxx: Enable IOCB throttling by default. - qla2xxx: Implementation to get and manage host, target stats and initiator port. - qla2xxx: Add SLER and PI control support. - qla2xxx: Do not log message when reading port speed via sysfs - qla2xxx: fix null pointer access. - qla2xxx: Use MPI hang trigger to do PEGTUNE halt. - qla2xxx: Reduce erroneous error in link reset path - qla2xxx: v2: fix stalled N2N reconnect. - qla2xxx: Fix warnings on SLES12SP5. - qla2xxx: Fix compilation issues on SLES15 - qla2xxx: Compilation Fixes for SLES15SP1. - qla2xxx: Debugfs compilation issue fix for RH7.6. - qla2xxx: Fix gcc test compile error output being printed. - qla2xxx: Timestamp device online and offline transitions. - qla2xxx: Add rport fields in debugfs. - qla2xxx: Allow dev_loss_tmo setting for FC-NVMe devices. - qla2xxx: Setup debugfs entries for remote ports. - qla2xxx: Fix edif related compilation issue on RH7.6. - Fixes for compilation on hpe branch - qla2xxx: Compilation fixes for RH8.2 - qla2xxx: Compilation changes for RH7.6 - qla2xxx: Fixes for compilation on RH7.x I - qla2xxx: bsg_job to bsg_job_t - qla2xxx: I Unify source code to work with newer kernels. - qla2xxx: Makefile changes from code-uni-devel-10x. - qla2xxx: qla_edif file changes to compile the driver. - qla2xxx: Fix compilation issues. - qla2xxx: Fix Makefile issue. - qla2xxx: fix compile error - qla2xxx: Use explicit LOGO in target mode - qla2xxx: Add EDIF support. - qla2xxx: Addd edif related files. - qla2xxx: Fix MPI failure AEN (8200) handling. - qla2xxx: SCM - Backport optimizations and style changes from upstream work. - qla2xxx: Fix warning in qla_attr.c file. - qla2xxx: Fix nvme compilation error. - qla2xxx: Fix crash in alloc w/GFP_KERNEL + interrupt - Author : Quinn Tran <qutran@marvell.com> qla2xxx: v2: add iocb resource tracking. - qla2xxx: Fix WARN_ON in qla_nvme_register_hba. - qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime. - qla2xxx: Make tgt_port_database available in initiator mode. - qla2xxx: reduce noisy debug message. - qla2xxx: Fix mailbox Ch erroneous error - qla2xxx: fix login timeout. - qla2xxx: Accomodate for SCM FW attribute bit change. - qla2xxx: post FC event (FPIN) to transport FPIN handler. - qla2xxx: Hide fc_host_fpin_rcv kernel dependency. - qla2xxx: Add changes to compile across various kernels. - qla2xxx: Use active targets to update SCM stats. - qla2xxx: Move SCM functions to qla_isr to keep changes local. - qla2xxx: Code to process FLOGI ACC extended payload. - qedf: Fix compilation issue - revisit. - qla2xxx: SCM Phase 1 Implementation + 2 other patches. - qla2xxx: Enable PUREX passthru post ISP reset. - qla2xxx: Fix hang when issuing nvme disconnect-all in NPIV. - qla2xxx: performance tweak - scsi: qla2xxx: fix fcport null pointer access. - fixup! qla2xxx: Fix unbound NVME response length. - scsi: qla2xxx: Fix unbound NVME response length - qla2xxx: Add host attribute to trigger MPI hang. - qla2xxx: ONEOFF: silent dbg messages for good path io. - qla2xxx: ONEOFF: fix pDIF detection - qla2xxx: Snoop inquiry response atleast 168 bytes to determine proprietary DIF. - qla2xxx: ONEOFF: add debug counters for T10-PI/DIF - qla2xxx: ONEOFF: add MQ support for HP3PAR propritary T10-PI - qla2xxx: HPE 3PAR private T10-PI support. - qla2xxx: Check for fabric_priority flag during login - qla2xxx: use iocb_fabric_priority flag - qla2xxx: Fix QoS name and add debug logs - qla2xxx: Correction to tests for iocb fabric and fcport qos. - qla2xxx: Use ->isp_ops->read_optrom() in qla26xx_read_qos_fcport_table(). - qla2xxx: QoS fcport table index initialization improvement. - qla2xxx: Add QoS fcport table index to speed up search. - qla2xxx: Reduce stack on qos fcport priority routines. - qla2xxx: HPE: Register FDMI QOS - qla2xxx: Add bsg interface for qos lun level bitmask. - qla2xxx: Read E2E QoS fcport priority bitmasks from flash. - qla2xxx: Abstract qos lun level mask for iocb cs_ctl field. - qla2xxx: Add fabric priority qos lun iocb mechanism. - qla2xxx: Implement CT command GFO (Get Fabric Object). - qla2xxx: Add support for fabric priority per target. - qla2xxx: fix mtcp dump collection failure. - qla2xxx: Set Nport ID for N2N - qla2xxx: Fix crash during device discovery. - qla2xxx: Handle NVME status iocb correctly. - qla2xxx: Remove restriction of FC T10-PI and NVME - qla2xxx: serialize fc_port alloc in N2N - qla2xxx: NPIV does not come up after FW dump. - qla2xxx: fix RDP respond data format bug. - qla2xxx: force semaphore on flash validation failure. - qla2xxx: add more FW debug information - qla2xxx: Revert: Disable T10-DIF feature with FC-NVMe during probe - qla2xxx: Update BPM enablement semantics. - qla2xxx: fix FW resource print error. - qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs. - qla2xxx: Ensure flash updates return possible failure status through bsg interface. - qla2xxx: Improved secure flash support messages - qla2xxx: fix flag passing error - qla2xxx: Use FC generic update firmware options routine for ISP27xx. - qla2xxx: Avoid setting firmware options twice in 24xx_update_fw_options. - qla2xxX: Add 16.0GT for PCI String - qla2xxx: Use FW_STARTED macro - qla2xxx: Add fixes for mailbox command - qla2xxx: Fix login IOCB flag - qla2xxx: Save rscn_gen for new fcport - qla2xxx: firmware option 3 is clobbered by speed set - qla2xxx: ISP28xx active FW region - qla2xxx: Add portname to print logs in qla24xx_logio_entry(). - qla2xxx: Correction to MB in-direction selection in qla2x00_echo_test(). - qla2xxx: Correction to selection of loopback/echo test. - qla2xxx: Use endian macros to assign static fields in fwdump header. - qla2xxx: Add Speed in SFP print information - qla2xxx: Fix RDP response size - qla2xxx: Handle cases for limiting RDP response payload length. - qla2xxx: Add deferred queue for processing ABTS and RDP. - qla2xxx: Cleanup ELS/PUREX iocb fields. - qla2xxx: Add devid's and conditionals for 28xx. - qla2xxx: Add vendor extended FDMI additions and amendments. - qla2xxx: Provide separate RDP enable. - qla2xxx: Add vendor extended RDP additions and amendments. - qla2xxx: Add changes in preparation for vendor extended FDMI/RDP. - qla2xxx: Add 2061 PCI ID - qla2xxx: Remove all DIX-0 references - qla2xxx: Add endianizer macro calls to fc host stats. - qla2xxx: Add sysfs node for D-Port Diagnostics AEN data. - qla2xxx: Move free of fcport out of interrupt context. - qla2xxx: Add beacon LED config sysfs interface. - qla2xxx: Add sysfs hooks for FC-NVMe autoconnect - 10.01.00.22-k AE 06/29/2020 - Upstream driver as part of Linux 5.6 - Please see user documentation for details. (Severity: Low) - Please see user documentation for details. (Severity: Low) - Please see user documentation for details. (Severity: Low) - Add workaround for MRRS of 5762 (Severity:Medium) - Add support for RHEL 7.4 and SLES12SP2 (Severity:Medium) - Add support to notify min/max MTUs through min_mtu & max_mtu (Severity:Medium) - Add support to overide clock for 5762 (Severity:Medium) - Backport upstream patches (Severity:Medium) - Add PHY reset workaround in change MTU path for 5717/19/20 (Severity:Medium) - Update the copyright (Severity:Minor) - Add SLES 15 support (Severity:Medium) - Add RHEL 7.5 support (Severity:Medium) - Fix RHEL 6.4 compilation (Severity:Medium) - Add Ubuntu 18.04 support (Severity:Minor) - Fix race between tg3_get_stats64() and tg3_free_consistent() (Severity:Minor) - Avoid usleep_range() with holding spin lock (Severity:Minor) - Add private ioctl support for register read/write (Severity:Medium) - Add RHEL 8.0 support (Severity:Medium) - Fix Panic with SLES12SP3 (Severity:Minor) - Add workaround for MRRS of 5762 (Severity:Medium) - Add support for RHEL 7.4 and SLES12SP2 (Severity:Medium) - Add support to notify min/max MTUs through min_mtu & max_mtu (Severity:Medium) - Add support to overide clock for 5762 (Severity:Medium) - Backport upstream patches (Severity:Medium) - Add PHY reset workaround in change MTU path for 5717/19/20 (Severity:Medium) - Update the copyright (Severity:Minor) - Add SLES 15 support (Severity:Medium) - Add RHEL 7.5 support (Severity:Medium) - Fix RHEL 6.4 compilation (Severity:Medium) - Add Ubuntu 18.04 support (Severity:Minor) - Fix race between tg3_get_stats64() and tg3_free_consistent() (Severity:Minor) - Avoid usleep_range() with holding spin lock (Severity:Minor) - Add private ioctl support for register read/write (Severity:Medium) - Add RHEL 8.0 support (Severity:Medium) - Fix Panic with SLES12SP3 (Severity:Minor)